Chicago Electricメーカー41213の使用説明書/サービス説明書
ページ先へ移動 of 19
7” ELECTRIC POLISHER / SANDER Model 41213 SET UP AND OPERA TING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally . Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight T ools ® .
Page 2 SKU 41213 For technical questions, please call 1-800-444-3353. SA VE THIS MANUAL Keep this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures.
Page 3 SKU 41213 For technical questions, please call 1-800-444-3353. GENERAL SAFETY RULES W ARNING! Read all instructions Failure to follow all instructions listed below may result in electric shock, re, and/or serious injury .
Page 4 SKU 41213 For technical questions, please call 1-800-444-3353. Avoid accidental starting. Ensure the switch is in the of f-position before plug- ging in. Carrying power tools with your nger on the switch or plugging in power tools that have the switch on invites accidents.
Page 5 SKU 41213 For technical questions, please call 1-800-444-3353. Service Have your power tool serviced by a qualied repair person using only identi - cal replacement parts. This will ensure that the safety of the power tool is maintained . VIBRA TION HAZARD This tool vibrates during use.
Page 6 SKU 41213 For technical questions, please call 1-800-444-3353. (1) Do not force the Polisher/Sander . This tool will do the work better and safer at the speed and capacity for which it was designed. Do not force the pads into the vehicle being waxed/polished.
Page 7 SKU 41213 For technical questions, please call 1-800-444-3353. When using the polisher , maintain a rm grip on the tool with both hands to resist starting torque. Use clamps (not included) or other practical ways to secure and support the workpiece to a stable platform.
Page 8 SKU 41213 For technical questions, please call 1-800-444-3353. GROUNDING Improperly connecting the grounding wire can result in electric shock. Check with a qualied electrician if you are in doubt as to whether the outlet is properly grounded.
Page 9 SKU 41213 For technical questions, please call 1-800-444-3353. dard Association, and the National Electrical Code. (See Outlets for 2-Prong Plug.) Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration.
Page 10 SKU 41213 For technical questions, please call 1-800-444-3353. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120/240 VOL T) NAMEPLA TE AMPERES (at full load) EXTENSION CORD LENGTH 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 18 18 18 18 16 2.
Page 1 1 SKU 41213 For technical questions, please call 1-800-444-3353. SPECIFICA TIONS Electrical Requirements 1 10 V~ / 60 Hz / 6 A (load) Motor No Load Speed 2 Speed (2800/ 3300) Arbor Diameter 7/8” Spindle Thread 5/8” - 1 1 UNP ACKING When unpacking, check to make sure that the item is intact and undamaged.
Page 12 SKU 41213 For technical questions, please call 1-800-444-3353. Depress the Stop Pin (3). Using the Wrench (49), T ighten the Flange Nut (47) by turning it clockwise until rmly in place. See Figure 1 below . Wrap a clean Polishing Bonnet (48) on top of the Backing Pad (46).
Page 13 SKU 41213 For technical questions, please call 1-800-444-3353. Controls Polishing Place a clean Polishing Bonnet (48) securely onto the Backing Pad (46).
Page 14 SKU 41213 For technical questions, please call 1-800-444-3353. 15 to 25 Degrees T o start, grip the Polisher rmly with both hands and press in on the ON/OFF Switch (24). Press the Lock-ON Button (22) to lock the Switch in the ON posi- tion.
Page 15 SKU 41213 For technical questions, please call 1-800-444-3353. Place a sanding disk, with a hole in the center of it, onto the Backing Pad (46) and secure it with the Flange Nut (47). T ighten the Flange Nut (47) using the Spanner Wrench (49).
Page 16 SKU 41213 For technical questions, please call 1-800-444-3353. MAINTENANCE AND SERVICING Risk of serious personal injury from accidental starting or electric shock.
Page 17 SKU 41213 For technical questions, please call 1-800-444-3353. Part # Description Qty Part # Description Qty 1 Screw 1 26 Brand 1 2 W asher 1 27 W asher 1 3 Stop Pin 1 28 Screw 1 4 Spring 1 29.
Page 18 SKU 41213 For technical questions, please call 1-800-444-3353. ASSEMBL Y DIAGRAM Note: Some parts are listed and shown for illustration purposes only , and are not avail- able individually as replacement parts.
Page 19 SKU 41213 For technical questions, please call 1-800-444-3353. Record Product’ s Serial Number Here: Note: If product has no serial number , record month and year of purchase instead.
デバイスChicago Electric 41213の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Chicago Electric 41213をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChicago Electric 41213の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chicago Electric 41213の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chicago Electric 41213で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chicago Electric 41213を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChicago Electric 41213の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chicago Electric 41213に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChicago Electric 41213デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
