Chicago Electricメーカー68316の使用説明書/サービス説明書
ページ先へ移動 of 20
Read this material before using this product. Failure to do so can result in serious injury . SA VE THIS MANUAL. Copyright © 2010 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight T ools.
Page 2 For technical questions, please call 1-800-444-3353. SKU 68316 T able of Contents Safety ......................................................... 2 Specications ............................................. 8 Setup .........................
Page 3 For technical questions, please call 1-800-444-3353. SKU 68316 5. When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Page 4 For technical questions, please call 1-800-444-3353. SKU 68316 Service Have your power tool serviced by a qualied repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Circular Saw Safety W arnings 1.
Page 5 For technical questions, please call 1-800-444-3353. SKU 68316 10. Check lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly . Never clamp or tie the lower guard into the open position.
Page 6 For technical questions, please call 1-800-444-3353. SKU 68316 30. W ARNING: Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause cancer , and birth defects or other reproductive harm. W ash hands after handling.
Page 7 For technical questions, please call 1-800-444-3353. SKU 68316 Grounding TO PREVENT ELECTRIC SHOCK AND DEA TH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualied electrician if you are in doubt as to whether the outlet is properly grounded.
Page 8 For technical questions, please call 1-800-444-3353. SKU 68316 Specications Electrical Rating 120V~ / 60Hz / 7.5A Motor No Load Speed 4200 RPM Blade Diameter 5″(125mm)Maximum UseO.
Page 9 For technical questions, please call 1-800-444-3353. SKU 68316 3. Use the Hex Wrench to tighten Side Handle Support securely into place. 4. Attach Side Handle to top of Side Handle Support using nut.
Page 10 For technical questions, please call 1-800-444-3353. SKU 68316 Operating Instructions Read the ENTIRE IMPORT ANT SAFETY INFORMA TION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Page 1 1 For technical questions, please call 1-800-444-3353. SKU 68316 5. Place new Blade A onto the Flange with the “A” clearly visible. A 6. Place Blade B onto Spindle with “B” clearly visible. B 7. Thread Lock Nut onto Spindle shaft and tighten Lock Nut until secure.
Page 12 For technical questions, please call 1-800-444-3353. SKU 68316 Using Lubrication Unit 1. The blades for the Double Cut Saw are “dry cut” teeth. This mean the blades only need to be lubricated in extreme cutting situations, such as when cutting aluminum, copper , stainless steel and cast iron.
Page 13 For technical questions, please call 1-800-444-3353. SKU 68316 General Operating Instructions 1. Make sure that all guards are in place and in proper working order and that all adjustment knobs are tight before operation. Do NOT operate Saw without blade guard or if blade guard is broken or not operating properly .
Page 14 For technical questions, please call 1-800-444-3353. SKU 68316 Cutting T echniques Rectangular Pipe Feed blade from corner to corner . Pipes Feed blade through object until it reaches lower edge, keeping blade at 90º angle. 3/8 in. Thin Plate Feedbladedownabout3/8″andstartcut.
Page 15 For technical questions, please call 1-800-444-3353. SKU 68316 Spiral T ube And Longitudinal Cutting Feed blade through material so only about3/8″showsthrough.Donotdrive it as far as entire cutting edge. Corner Piece Feed blade diagonally through the work surface.
Page 16 For technical questions, please call 1-800-444-3353. SKU 68316 Maintenance and Servicing Procedures not specically explained in this manual must be performed only by a qualied technician.
Page 17 For technical questions, please call 1-800-444-3353. SKU 68316 T roubleshooting Problem Possible Causes Likely Solutions T ool will not start. 1. Cord not connected. 2. No power at outlet. 3. T ool’s thermal reset breaker tripped (if equipped).
Page 18 For technical questions, please call 1-800-444-3353. SKU 68316 Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE P ARTS LIST AND ASSEMBL Y DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONL Y .
Page 19 For technical questions, please call 1-800-444-3353. SKU 68316 Assembly Diagram Record Product’ s Serial Number Here: Note: If product has no serial number , record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 9301 1 • (800) 444-3353 Limited 90 Day W arranty Harbor Freight T ools Co. makes every effort to assure that its products meet high quality .
デバイスChicago Electric 68316の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Chicago Electric 68316をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChicago Electric 68316の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chicago Electric 68316の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chicago Electric 68316で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chicago Electric 68316を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChicago Electric 68316の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chicago Electric 68316に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChicago Electric 68316デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
