Cisco SystemsメーカーEngine 611の使用説明書/サービス説明書
ページ先へ移動 of 14
Corporate Headquarters: © 20 05 Cisco Syst ems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Installing Hard Disk Drives in the Cisco Wide Area Ap.
2 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Safety Overview Protecting Against Electrostatic Discharge Static electricit y can harm delicate componen ts insi de the de vice.
3 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Introduction Introduction The W AE-611 supports two 1-inch (2 .54-cm) slim 3.5-inch (8.89-cm) lo w voltage dif ferential (L VD) hard disk dri ves. The W AE-611 requires SCSI hard disk dri ves.
4 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Removing the Bezel and Cover Removing the Bezel and Cover War ni ng Before working on a sy stem that has an on/off switch, turn OFF the po wer and unplug the power cord.
5 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Removing the Beze l and Cover Figur e 2 Removing the Co v er Step 5 Slide the cov er back. Lift it up and of f the device. Caution For proper cool ing and airflo w , replace the cover before tu rning on the de vice.
6 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Assigning SCSI IDs Figur e 3 Location of Dr ive Ba ys Behind the Bez el Assigning SCSI IDs When you install or replace one or more of the SCSI disk dri v es in a W AE-611, you must assign a SCSI ID to each disk dri ve.
7 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Removing and Repl acing a SCS I Hard Disk Dri ve Figure 4 Hard Disk Dr ive Connec tors and SCSI ID Jumper Pins Step 2 T o check whether the configuration is correct, refer to the b oot time messages on th e de vice consol e.
8 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Removing and Replac ing a SCSI Hard Disk Drive Step 3 Po wer do wn the de vice and peripheral de vices, and disconnect the po w er cord and all external cables. Step 4 Press the release tabs on the bezel, and pull the bezel a way from the chassis.
9 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Replacing the Cover and B ezel and Completin g the Installation Step 11 Connect the power and SCSI cables to the dri ve. If you disconnected the IDE cable to the CD-R OM, reconnect it.
10 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Obtaining Documentation T o complete your instal lation, follo w these steps: Step 1 Install the cov er . Place it into position, slide it forw ard, and then tighten the ca ptiv e screw (l abeled 1 in Figure 2 ).
11 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Obtaining Technical Assista nce If you prefer to see advisories an d notices as they are updated in real time, you can acces s a Product Security Incident Response T eam Really Simple Syndication (PSIR T RSS) feed from this URL: http://www .
12 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Obtaining Technica l Assistance Access to all tools on the Ci sco T echnical Support & Documentat ion website requires a Ci sco.
13 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Obtaining Technical Assista nce Definitions of Service Request Severity T o ensure that all s ervice reque sts are rep orted in a standard format, Cisco has established se verity definitions.
14 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Obtaining Technica l Assistance This document is to be used in co njunction with th e documents listed i n the “Related Documentation” section. © 2006 Cisc o Systems, Inc.
デバイスCisco Systems Engine 611の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Cisco Systems Engine 611をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCisco Systems Engine 611の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cisco Systems Engine 611の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cisco Systems Engine 611で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cisco Systems Engine 611を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCisco Systems Engine 611の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cisco Systems Engine 611に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCisco Systems Engine 611デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
