CitizenメーカーCT-S280の使用説明書/サービス説明書
ページ先へ移動 of 33
LINE THERMAL PRINTER MODEL CT -S280 User’ s Manual.
WEEE MARK ,I RX ZDQWWR GLVSRVH W KLV SURGXFW GRQRW PL[ ZLWK JHQHUDO KRXVHKROG ZDVWH 7KHUH LV D VHSDUDWHFROOHFWLRQVVWHPV IRUXVHGHOHF.
This printer conforms to the following Standards: The Low V oltage Directive 2006/95/EC, formerly 72/23/EEC, the EMC Directive 2004/108/EC, formerly 89/336/EEC, the RoHS Directive 2002/95/EC, and the WEEE Directive 2002/96/EC. LV D: EN60950 EMC : EN55022 Class A EN61000-3-2 EN61000-3-3 EN55024 This declaration is applied only for 230V model.
IMPORT ANT : This equipment generates, uses, and can radiate radio frequency ener gy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
— 1 — GENERAL PRECAUTIONS ● Before using this product, be sure to read through this manual. After having read this manual, keep it in a safe, readily accessible place for future reference. ● The information contained herein is subject to change without prior notice.
— 2 — SAFETY PRECAUTIONS ... WHICH SHOULD BE STRICTL Y OBSERVED Before using this product for the first time, carefully read these SAFETY PRECAUTIONS. Incorrect operation may result in unexpected accidents (fire, shock, or injury). ● After having read this Manual, keep it in a safe, readily accessible place for future reference.
— 3 — Do not use or store this product in a place where it will be exposed to: ● Flames or moist air ● Direct sunlight ● Hot airflow or radiation from a heating device ● Salty air or corro.
— 4 — Place the printer on a flat, stable surface without vibration. • Otherwise dropping may cause injury . Do not use the printer under the following conditions.
— 5 — PRECAUTIONS IN HANDLING THE PRINTER Please observe the following precautions for power source and power cord: ● Do not plug or unplug the power cord with a wet hand. ● Use the printer only at the specified supply voltage and frequency . ● Use only the specified AC adapter with the printer .
— 6 — Caution label is attached on the position shown in the following figure. Carefully read the precautions in handling before using the printer . THIS LABEL INDICA TES THE RISK OF ANY INJURY DUE TO “ HIGH TEMPERA TURE ” OF THE PRINT HEAD. T o prevent possible malfunction or failure observe the following.
— 7 — Observe the following precautions for daily maintenance. ● When cleaning the printer , always turn it off and unplug it from the supply outlet. ● Use a soft, dry cloth for cleaning the surface of the printer case. ● For severe stains, use a soft cloth slightly dampened with water .
— 8 — THE T ABLE OF CONTENTS 1. GENERAL OUTLINE ................................................................... 9 1.1 Features .......................................................................................... 9 1.2 Unpacking .........
— 9 — 1. GENERAL OUTLINE The CT -S280 is a thermal line printer designed for use with a broad array of terminal equipment including, data, POS, and kitchen terminals. With extensive features, it can be used in a wide range of applications. 1.1 Features ● Compact design.
— 10 — CT -S 280 RS U - WH Case color WH: Cool white BK: Black Destination (Letters + Power cord) J: Japan E: Europe U: USA 1.3 Model Classification The printer models are classified by the following designation method: Interface P A: Parallel IEEE 1284 compliant RS: Serial RS-232C compliant UB: USB Model name 1.
— 11 — Item Specifications Model CT -S280RSU CT -S280RSE CT -S280RSJ CT -S280PAU CT -S280P AE CT -S280P AJ CT -S280UBU CT -S280UBE CT -S280UBJ Print method Line thermal dot print method Print widt.
— 12 — 2. EXPLANA TION OF PRINTER P ARTS 2.1 Printer Appearance Paper cover Power switch Cover open button Operation panel ● Paper cover Paper is located inside this cover . ● Cover open button T o refill or replace paper , open the paper cover by pushing this button.
— 13 — ● POWER LED Lights when the printer power is on and goes off when the printer power is off. May blink or light in a special mode or in case of a failure. ● FEED switch Pressing this switch once causes a paper feed of one line. Pressing the switch continuously causes the paper to feed continuously .
— 14 — 2.2 Paper Cover Inside ● Paper cutter Used to cut paper at the time of paper setting or at the end of printing. ● Print (thermal) head Prints characters and/or graphic data on thermal paper . ● Paper -end sensor Stops printing when this sensor detects paper end.
— 15 — 3. PREP ARA TION 3.1 Connecting the AC Adapter and AC Power Cord 1. T urn off the printer power . 2. Plug in the cable connector of the AC adapter to the power connector at the rear of the printer . 3. Connect the AC power cord to the inlet of the printer , and insert the AC power-cord plug into a suitable wall outlet.
— 16 — Printer Pin Signal 2T X D 3R X D 4R T S 6 DSR 7S G 20 DTR PC Signal Pin FG 1 TXD 2 RXD 3 CTS 5 DSR 6 SG 7 DTR 20 3.2 Connecting Interface Cables T urn off the printer and unplug the power connector . Then follow the procedure for interface cable connection.
— 17 — 3.3 Installing the Printer The printer can be installed horizontally or on the wall. At the time of shipment, the printer is set for horizontal installation. T o install the printer on the wall, the following adjustments are required. Hooks for wall mounting Horizontal position W all mounting n3 n5.
— 18 — Initial Settings 1 Communication condition DIP switch setting Internal memory ON setting method setting 2 Hand shake XON/XOFF DTR/DSR OFF 3 Bit length 7 bits 8 bits OFF 4 Parity check With parity None OFF 5 Parity selection Even parity Odd parity OFF 6 OFF 7 ON 8 Reserved − Fixed OFF Selecting baud rate Switch No.
— 19 — 3.5 Adjusting the Paper Near -end Sensor 1. Push in the paper near -end sensor unit. 2. Move the paper near -end sensor unit to the right and left while pushing it. The position to be set varies in accordance with the setting of the printer , horizontal or wall mounting, or the diameter of the paper roll as shown in the following figure.
— 20 — 4. MAINTENANCE AND TROUBLESHOOTING 4.1 Setting/Replacing Paper Rolls 1. Pull the cover open button fully toward you. 2. Open the paper cover . 3. Insert a paper roll with is print area facing down as shown in the figure and pull out the paper end straightforward by several cm out of the printer .
— 21 — 4.2 Removing Jammed Paper 1. T urn the printer power off. 2. Open the paper cover . 3. Remove the jammed paper including any paper chips remaining. (Also take out the paper roll from the holder .) 4. T urn on the printer and set paper roll to the holder .
— 22 — CT-S280 V1.xxx Serial Interface Baud rate : 19200 bps Data bit : 8 bits Parity : None Handshaking : DTR/DSR Buffer Size 4K Bytes Dip switches DS1 1 2 3 4 5 6 7 8 ON O O O OFF O O O O O Memory switches SW1 1 2 3 4 5 6 7 8 ON OFF O O O O O O O O SW2 1 2 3 4 5 6 7 8 ON O O O OFF O O O O O SW3 1 2 3 4 5 6 7 8 ON OFF O O O O O O O O 4.
— 23 — 4.6 Error Indication ● Paper end Paper empty is detected in two steps: paper near -end and paper end. It causes the ERROR LED to light. If paper end is detected, refill the paper .
— 24 — 5. OTHER 5.1 External V iews and Dimensions (Unit: millimeter) 106 116.5 60 170 POWER FEED ERROR.
— 25 — 5.2 Printing Paper Use the print paper shown in the following table or the paper with equivalent quality . Paper T ype Product Name Recommended thermal TF50KS-E2D from Nippon Paper paper ro.
— 26 — 5.3 Manual Setting of Memory Switch Memory switches can be set manually or by a command. For manual setting, refer to the next page. The function of each memory switch is shown in the following table. (The white-on-black characters are factory setting.
— 27 — Manual Setting of Memory Switch (Memory SW) The memory switch can be selected, changed, or written by the combination of three actions: pressing the FEED switch, pressing and holding the FEED switch, and opening or closing the paper cover .
— 28 — 5. Returning to the memory switch select mode When the setting of the desired content is completed, open the paper cover and then close the paper cover .
TE74924-00F 1.05E-0904 Printed in Japan.
デバイスCitizen CT-S280の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Citizen CT-S280をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCitizen CT-S280の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Citizen CT-S280の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Citizen CT-S280で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Citizen CT-S280を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCitizen CT-S280の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Citizen CT-S280に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCitizen CT-S280デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
