CMA DishmachinesメーカーCMA-180の使用説明書/サービス説明書
ページ先へ移動 of 19
MODEL CMA-180 Installation & Operation Rev 2.03 800-854-6417 FAX 714-895-2141 CMA DISHMACHINES 12700 KNOTT AVENUE GARDEN GROVE, CALIFORNIA 92841 www.
Table of Contents CMA-180 1. SPECIFICATIONS ................................................................................................. 2 1.1 CMA-180/CMA-180T ......................................................................................
1. S pecifications 1.1 CMA-180/CMA-180T Metric Equivalent WATER CONSUMPTION PER RACK .96 GAL. (3.6 L) PER HOUR 52 GAL. (197 L) OPERATING CYCLE WASH TIME-SEC RINSE TIME-SEC TOTAL CYCLE 49 12 61 MIN. 49 12 61 MIN. OPERATING CAPACITY RACKS PER HOUR (NSF rated ) WASH TANK CAPACITY PUMP CAPACITY 60 8 GAL.
1.1. CMA-180/CMA-180T ELECTRICAL RATING VOLTS PHASE AMPS WITHOUT BOOSTER 208 1 28/35 240 1 30/38 208 3 20/24 240 208 240 208 ELECTRICAL RATING WITH BOOSTER 240 3 1 1 3 3 21/26 71/78 80/88 45/49 50/55 SHIPPING WEIGHT 332# WITHOUT BOOSTER 375# WITH BOOSTER MODEL CMA-180 INST ALLATION & OPERATION Re v.
2. Getting S t arted 2.1. Introduction to CMA-180 The CMA-180 is a hot wa ter sanitizing, single rack, door-type dishmachine. It is a stand-alone machine featuring a self-contai ned booster heate r (optional). The only external connections necessary are power supply, water supply, drai npi pe, and chemical di spensers.
2.2. Receiving and Installation Step 1: Remove packaging material. Step 2: Remove service manual and machi ne legs from inside the wash tank . Step 3: Install legs into dishmachine leg lockets and adju st the feet. Set the machine in place. Level the machine side – to – side and front – to – back .
flexibility to permit the machine to be moved for cleaning without having to disconnect any wiring. ii. Run your dispenser wires throug h the conduit to the control box.
2. Remove the plug from the mixing cham ber lo cated by the vacuum breake r on the back of machine; and install the rinse inj ection fitting (sup plied with your dispenser). 3. A 7/8” detergent injection hole is provid ed in the back of the wash tank.
2.2.4. Exhaust Fan Control MODEL CMA-180 INST ALLATION & OPERATION Re v. 2.03 Page 8.
2.2.5. Water Tempering Kit MODEL CMA-180 INST ALLATION & OPERATION Re v. 2.03 Page 9.
2.2.6. Installation Checklist Dishmachine checke d for co ncealed damage. Hot water supply is 140° (60°C) Incoming water supply line is ¾”. Incoming water supply is 6 gpm minimum ca pable at 20 psi flow pressure. Machine circuit breake r is properly sized.
2.2.7. Machine Start-Up Procedures 1. Open doors and install the overflow & scrap trap on the right side of the machin e. 2. Place the scrap baskets over the wash tanks. 3. Secure the wash & rinse arms and check the free -spin. 4. Open the control cover and sele ct ‘normal” toggle swit ch po sition.
2.2.8. Electrical Requirements The CMA-180 comes standard factory, wired for 3- pha se operation. Check t he electrical data plate to confirm this. If the acco unt requires 1 phase, refer to “El ectrical Requirements”, Se ction 1-A, for proper wiring inst ruction for conversi on.
3. Wiring Options 3-Phase and 1 Phase Wiring Options Single-Source 220V 3-Phase (20 amp/12 g*) Single-Source 220V 3-Phase (50 amp/8 g*) Single-Source 220V 1-Phase (80 amp/4 g*) Two-Sour ce 220V 1-Phase (50 amp/8 g*) (30 amp/10 g*) Single-Source 220V 1-Phase (30 amp/10 G*) (without Booster) (without booster) *g=gauge DISPENSER HOOK-UP 1.
4. Quick service g uide MODEL: CMA 180 HIGH TEMP TECHNICA L ISSUE CA USE SOLU TION Door magnetic reed switch problem Faulty magnetic reed switc h Check wire connec tions inside control box Contact fact ory for new retrofit, c orner P/N 00566.10 straight P /N 00566.
5. INITIAL P ARTS KIT P/N 1 100.17 P/N DESCRIPTION NO. REQ’D 00121.18 CMA-180 Drain Stopper O Ring 1 00200.10 Pump Assy 110/220V 60 Hz (Open) 1 00206.00 Pump Seal Kit 1 00302.19 CMA-180 Buna Gasket (#302.17) 1 00304.17 CMA-180 Wash Spray Arm 1 00304.
6. Auto-Fill Solid St ate T imer 1 23 6 AUTO-FILL SWITCH WATE R SOLENOID VALV E WASH PUMP CONTACTOR T1 T2 L1 L2 Pre-selected delay period can b e adjusted by turning securely small flat screwd river. Since the range of this solid state timer is from 6 seconds to 2 40 se conds, y ou should adjust delay by small increment.
7. Wire Diagram MODEL CMA-180 INST ALLATION & OPERATION Re v. 2.03 Page 17.
8. Wire Diagram for CMA-180 Booster Only WASH PUM P CONTACTOR T1 T2 L1 L2 GROU ND PUMP MOTOR WASH TANK HEATER HEATER CONTACTOR T1 T2 T3 L1 L2 L3 5kW BOOSTE R HEATER CONTACTOR T1 T2 T3 L1 L2 L3 L1 L2 L3 GND RINSE SIGNAL { DETERGENT { 12kW BOOSTER HEATER ADJ.
デバイスCMA Dishmachines CMA-180の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
CMA Dishmachines CMA-180をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCMA Dishmachines CMA-180の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。CMA Dishmachines CMA-180の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。CMA Dishmachines CMA-180で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
CMA Dishmachines CMA-180を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCMA Dishmachines CMA-180の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、CMA Dishmachines CMA-180に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCMA Dishmachines CMA-180デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
