CMA DishmachinesメーカーGL-Xの使用説明書/サービス説明書
ページ先へ移動 of 19
www.cmadishmachines.com 800-854-6417 FAX 714 - 8 95 - 2 141 CMA DISHMACHINES 12700 KNOTT AVENUE GARDEN GROVE, CALIFORNIA 92841 MODEL GL-X INSTALLATION & OPERATION Rev.
T ABLE OF C ONTENTS M ODEL CMA-GL-X 1. SPECIFICAT IONS ......................................................................................... 2 1.1. GL-X ..............................................................................................
1. S pecifications METRIC EQUIVALENT 1.1. GL-X WATER CONSUMPTION PER RACK 1.7 GAL. 6.44 L PER HOUR 40.8 GAL. 154.4 L OPERATING CYCLE WASH TIME-SEC 57 57 RINSE TIME-SEC 48 48 DWELL TIME-SEC 15 15 TOTAL CYCLE 2 MIN. 2 MIN. OPERATING CAPACITY RACKS PER HOUR 30 30 WASH TANK CAPACITY 1.
1.2. GL-X Operational Cycle The GL-X Operational Cycle has a total cycle time of 2 m inutes (120 seconds). The Timing Diagram and the steps listed below de tail the individual functions that are executed during each Operational Cycle.
The pump motor runs the pump for the 57-s econd wash cycle, then pumps the water out through the drain, turns off for about 8 seco nds (allowing the machine to refill with clean rinse water) and then runs the pump for the 48-second rinse cycle. 3. Cam switch 3 controls the drain function.
Getting Started 2. Getting S t arted 2.1. Introduction to the GL-X The GL-X Glasswasher is unique in its field; it has all the features of a standa rd commercial size machine packed into an under-cou nter, standalone glasswasher. Operation of the GL-X is extremely easy.
Getting Started 2.2. Receiving and Installation The glasswasher is shippe d from the factory in a corru gated box on a wooden pallet. The installation guidelines give a systematic pro cedure for setting up the machine. 1. Start by removing the box and packaging mate rial.
Getting Started 2.2.4. Installers Checklist Glasswasher checked for concealed damage Hot water supply is recommended 140° F (60 C) Incoming water supply line is ½” minimum Supply c.
Operation 3. Operation 3.1. Initial Setup 3.1.1. Check… Drain screen is in place Spay arms and end plugs are secure 3.1.2. Chemicals • Assure there is a sufficient supply of chemicals before beginning a shift.
Operation These cams were set at the factory but must be adj usted after final installation to maximize efficien cy of chemical use ( se e section 4.1.1 Cam Adjus tment .) 3.2.3. Proper Filling The number 4 cam determi nes the am ount the mach ine is automatically filled each cy cle.
Maintenance 4. Maintenance The maintenance proced ures detail ed in this sect ion are to be performed by quali fied personnel. 4.1. Timer assembly The standard timer assem bly con sists of a (2 minutes per revolution) moto r turning a common shaft, which, in turn, rotates eight cams.
Maintenance 4.2. Quick service guide MODELS: GLX TECHNICA L ISSUE CAUSE SOLUTION Delim er s w it ch in d e lim e po s it ion Fl ip t o NORMAL position Wash Pump motor will not shut off Faulty delimer switch Replace switch, P/N 00475.30 Faulty manual drain switch Replace switch, P/N 03406.
Maintenance 4.3. Troubleshooting PROBLEM LIKELY CAUSE SOLUTION Power off at circuit breaker Reset circuit breaker Defective power swit ch Replace power switch P/N: 00433.10 Machine inoperative Defective timer assembly motor Replace timer assembly motor P/N: 00501.
Maintenance PROBLEM LIKELY CAUSE SOLUTION Turn up supply water heate r Low incoming water temperature (below 140° F) Insulate supply water pipe Thermostat out of adjustment Adjust thermostat Low heat during operation Defective sustainer heater Replace heat er P/N: 04109.
Maintenance PROBLEM LIKELY CAUSE SOLUTION Defective sani/detergent primer switch Replace primer switch P/N: 03470.00 Activating detergent primer switch does not run pum p Defective detergent pump motor Replace pump motor P/N: 00416.00 Defective sani/detergent primer switch Replace primer switch P/N: 03470.
Addendum 5. Addendum for Machines Installed in the City of Chicago “All food dispensing e stablishments using chlorine o r other approved chemical sanitizers shall, at all times, maintain an adequate testing devi ce.
Appendix A: Operator & Cleaning Instructions MODEL GL-X INSTALLATION & OPERATION MANUAL Rev. 1.00 A –08/04/05 PAGE 16.
Electrical Diagram 6. Electrical Diag ram MODEL GL-X INSTALLATION & OPERATION MANUAL Rev. 1.00 A –08/04/05 PAGE 17.
Electrical Diagram MODEL GL-X INSTALLATION & OPERATION MANUAL Rev. 1.00 A –08/04/05 PAGE 18.
デバイスCMA Dishmachines GL-Xの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
CMA Dishmachines GL-Xをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCMA Dishmachines GL-Xの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。CMA Dishmachines GL-Xの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。CMA Dishmachines GL-Xで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
CMA Dishmachines GL-Xを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCMA Dishmachines GL-Xの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、CMA Dishmachines GL-Xに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCMA Dishmachines GL-Xデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
