CNETメーカーCWP-905の使用説明書/サービス説明書
ページ先へ移動 of 69
CWP-905 Wireless-N PCI Adapter User Manual V ersion: 1.0 (July , 2007).
T able of Contents Chapter 1: Introduction ........................................................................................... 3 1.1 About CWP-905 ...................................................................................... 3 1.2 Main Features .
Chapter 1: Introduction 1.1 About CWP-905 Thank you for purchasing this high-speed 802.1 1 b/g/n (Draft 2.0) wireless adapter . The Wireless-N PCI Adapter can be installed in mo st desktops and provides true flexibility by allowing the computer to be positioned almost anywhere in the building without the cost and hassle of running network cables.
1.3 System Requirement s • An empty PCI slot • Windows 2000, XP , or V ista operating system • CD-ROM drive • At least 100MB of available disk space 1.
Chapter 2: Driver Inst allation and Configuration 2.1 Netw ork Card Inst allation Please follow the following instructions to install your new wireless network card: 1. SWITCH THE COMPUTER OFF , remove the cover and insert the wireless network card into an empty PCI slot of your computer .
3. Switch the computer on, the following me ssage will appear on your computer , please click ‘Cancel’ . 4. Insert the Auto-Install CD into your CD-RO M drive. Unless you hav e disabled the auto-run feature of Windows, the AutoPlay Menu should appear automatically .
5. Please read the end user license agreement and click ‘Y es’ to accept license agreement. 6. Y ou can choose the configuration tool used to configure the wireless network card here. It’s recommended to select ‘Ralink Configuration T ool’, which provides fully access to all function of this wireless network card.
7. There are two wireless performance mode you can select here: Optimize for WiFi mode or Optimize for performance mode If you want to enhance wireless performance, please select ‘Optimize for performance mode’. However , wireless compatibility is not guaranteed in this mode.
8. Please click ‘ Inst all’ to run the driver installation process. 9. When you see this message, please click ‘Fin ish’ to complete the driver installation process.
10. A new icon will appear at lower-right corner of your computer de sktop, you can put the mouse cursor on the icon, and the status of wireless card will be displayed as a popup balloon. HERE! 11. When you want to configure your wireless co nnection, please rig ht click on this icon, and a popup menu will appear .
2.2 Connect to Wireless Access Point There are two ways you can configure your wireless network card to connect to wireless access point: using the Ralink configuration utilit y which comes with wireless card driver , and using built-in windows zero configuration utility .
Here are descriptions of every setup item: SSID: The Service Set IDentifier of wireless access point or other network device. Y ou can think it as the name of access point of wireless device. BSSID: The MAC address of wireless ac cess point or other network device.
uses. Encryption: Shows the encryption method that access point or wireless device uses. If the wireless access point does n ot enable encryption, you’ ll see ‘None’ displayed here. Authentication: Shows t he authentication mode that access point or wireless device uses.
If the access point you selected does not enable encryption (The content of ‘Encryption’ field of the access point you selected is ‘None’, you’ll be connected to this wireless access point within one minute. Please jump to step 6. If the access point you selected enables enc ryption, please proceed to next step.
5. If the wireless access point uses encrypti on, you have to input WEP p assphrase or WP A preshared key . Please ask the owner of the wireless access point you want to connect, and input the correct passphrase / preshared ke y here, then click ‘OK’.
wireless device you connected to) message display ed at lower-left corner of configuration utility , congratulations, you’re successfully connected to the access point or wireless device you selected! 7.
2-2-2 Using Windows Zero Configuration Windows XP and V ista has a built-in wireless netwo rk configuration utility , called as ‘Windows Zero Configuration’ (WZC). Y ou can also us e WZC to configure your wireless network parameter: 1. Right-click Ralink configuration utility ic on and select ‘Use Zero Configuration as Configuration utility .
4. Right-click ‘Wireless Network Connection’ (i t may have a number as suffix if you have more than one wireless network card, pl ease make sure you rig ht-click the ‘Ralink 802.1 1n Wireless LAN Card), then select ‘View Available Wireless Networks’.
6. If the access point is protec ted by encryption, you have to input its security key or passphrase here. It must match the encryption setting on the access point. If the access point you selected does not us e encryption, you’ll not be prompted for security key or passphrase.
7. If you can see ‘Connected’ message, the connection between your computer and wireless access point is successfully established. 20.
2.3 Connection Profile Management If you need to connect to different wireless access point s at different time, like of access point of your home, office, cybercafe, or public wireless service, you can store the connection parameters (encryption, passphrase, security etc, etc.
Or , you can add a connected wireless access poi nt or wireless device to a profile by clicking ‘Site Survey’ tab, then click ‘Add to Profile’ button: 22.
Y ou can set the parameter for this connection here: 23.
Here are descriptions of every setup items: Profile Name Please give this profile a name, up to 32 alphanumerical characters and symbols are allowed, but sp ace is not allowed. SSID The SSID of the wireless a ccess point or wireless device you selected will be displayed here.
it is. Now click ‘Authenticatio n and Security’ tab, and set the en cryption and authentication settings. Here are descriptions of every setup items: Authentication Select the authent ication type of the wireless access T ype point or wireless device you wish to connect.
Encryption: Select the encryption type of the wireless access point or wireless device you wish to connect. If y ou’re adding a profile from an existing access point or wireless device, the value will be selected automatically , and please do not modify it.
Use 802.1x Enable 80 2.1x wireless authentic ation. Please click ‘802.1x Setting’ button to set 802.1x parameters. (See next section). After you finish all settings, click ‘OK’ to save settings and exit.
If you no longer need a profile, select the profile then click ‘Delete’. 28.
2-3-2 Using 802.1x – Certification After you click ‘802.1x Setting’, a new window will appear: Here are descriptions of every setup items: Authentication Please select an 802.1x authentication type here. T ype The type you select here m ust be identical to the type of the 802.
Domain Name Please input the domain nam e of 802.1x authentication here. This field will be grayed out when authent ication type is not ‘EAP-F AST’. Use Client If the authentication type you use is ‘PEAP’ or ‘TTLS’, you can use the certificate stored on your co mputer .
mode. This setting is hidden when the authentication type is not ‘EAP-F AST’. After you finish all settings, click ‘OK’ to save settings and exit.
2-3-3 Using 802.1x - CA Server If you want to use CA server , please click ‘CA Server ’ tab. And the following message will be displayed: Here are descriptions of every setup items: Use certificate Check this box to enable the use of certificate chain.
2.4 View Netw ork S t atistics and Link St atus The configuration utility provides informati on about network statistics and link status. If you want to know how your wireless network card works, you can use these functions to get detailed information about the wi reless connection you’re using.
the statistics of all items back to 0. Click ‘OK’ to close the window . 34.
2-4-2 Link S tatus Please follow the following instructi ons to check network statistics: 1. Right-click the Ralink configur ation utility icon located at lo wer-right corner of computer desktop, then click ‘Launch Config Utilities’.
every item: S tatus Display the SSID and BSSID of c onnected wireless access point or wireless device (displayed as SSID <-> BSSID as shown in above picture. If there’s no active connection currently , ‘Disconnected’ will be displayed here.
2.5 Advance Settings This wireless network card provides several advanced settings for experienced wireless users. Y ou can change these settings to increase data transfer performance, or change operation mode. Please follow the following instructions to set advanced wireless settings: 1.
Here are descriptions of every setup items: Wireless mode Select wireless operation m ode, available options are 802.1 1 B/G mix, 802.1 1 B only , and 802.1 1 B/G/N mix. Y ou can select 802.1 1 B/G/N mix to maximize wireless com patibility with wireless access points and other wireless devices.
Select Y our Select the country / region code of the place you’re Country Region living. Different country / region has dif ferent Code regulations on wireless devices, and it’ s forbidden to use certain channel (radio frequency) in some countries or regions.
2.6 QoS Settings This wireless network card provides QoS (Qualit y of Service) function, which can improve the performance of certain network applications, like audio / video streaming, network telephony (V oIP), and others.
Here are descriptions of every setup items: WMM Enable Check this box to enable WMM function. Please click ‘Apply’ button on the right of this check box af ter you check or uncheck this box, so corresponding settings in this window will be activated or deactivated respectively .
Direct Link Enable or disable direct link setup (DLS) function. Setup Enable This function will greatly improve the data transfer rate between WMM-enabled wireless devices.
2.7 WPS Configuration Wi-Fi Protected Setup (WPS) is the latest wi reless network technology which makes wireless network setup become very simple. If you have WPS-enabled wireless access point, and you want to establish a secure connection to it, you don’t have to configure the wireless access point and setup data encryption.
2-7-1 WPS Setup - PBC (Pus h-Button Configuration) 1. Right-click the Ralink configur ation utility icon located at lo wer-right corner of computer desktop, then click ‘Launch Config Utilities’.
3. Push the ‘WPS’ button on your wireless a ccess point (the button used to activate WPS standby mode may have another name), or use ot her way to start WPS st andby mode as the instruction given by your wire less access point’s user manual.
network card and access point is successfully connected by WPS, and the information about access point you connected to will be displayed. Sometime WPS may fail, and you can click ‘PBC’ bu tton few more times to try again.
desktop, then click ‘Launch Config Utilities’. 2. Click ‘WPS Configuration’ tab, and the following settings will appear: The PIN number of your wireless network card is an eight-digit number located at the upper-right position of con figuration utility .
3. Click ‘PIN’ button now , and wait for few se conds to one minute. If a wireless access point with correct PIN code is found, you ’ll be connected to that access point: Y ou may have to click ‘PIN’ for few more time s to try again.
2.8 About The ‘About’ tab provides you the information about version numbers of configuration utility , firmware, and other important informat ion about your wireless network card. Please follow the following instructions to see these information: 1.
The About screen shows release dates as well as driver/utility versions and the MAC/IP address of the card. Please click ‘OK’ to close configuration utility .
Chapter 3: Sof t-AP Function Excepting become a wireless client of other wire less access points, this wireless card can act as a wireless service provider also! Y ou can swit ch this wireless card’.
Config Utilities’ after you right -click the Ralink configuration ut ility , which asks you to assign an existing network card with internet connection: If your computer has another network card whi.
Here are descriptions of every setup items: SSID Please input the SSID (the name used to identify this wireless access point) here. Up to 3 2 numerical characte rs can be accepted here, excepting space. TX Rate Please select the data transfer rate here.
channels available here will vary depends on the setting of ‘Country Region Code’. Wireless Mode Please select the wireless operating mode. Y ou can limit the type of wireless client to 802.1 1b or 802.1 1g only , or allow 802.1 1b/g, and 802.1 1b/g/n clients.
know what will be affected. TX Power Y ou can select the wireless output power here. Please select a proper output power setting according to your actual needs. Y ou may not need 100% of output power if other wireless clients are not far from you. Idle Ti me Select the idle time of your wireless network card.
3.2 Security Settings This wireless card supports wireless encryption in AP mode, which will encrypt the dat a being transferred over the air to enhance data security level. It’ s recommended to enable data encryption unless you wish to open your computer (and its internet connection) to the public.
be encrypted and people with some networking knowledge will be able to read the data you transfer with proper tool. NOTE: WP A encryption is safer than WEP , however , some older wireless clients don’ t support WP A encryption. WP A Pre-shared Please input the WP A pre-shared key here.
3.3 Access Control If you’re not going to open your computer and wi reless resources to the public, you can use MAC address filtering function to enforce your access control policy , so only wireless clients with MAC address you defined by this functi on can be connected to your software access point.
Here are descriptions of every setup items: Access Policy Select the policy type of your access rule: Disable: Allow any wireless client with proper authentication settings to connect to this access point. Allow All: Only allow wireless clients with MAC address listed here to connect to this access point.
you wish to allow or reject here. No colo n (:) or hyphen (-) required. Add Add the MAC address you inputted in ‘MAC address’ field to the list. Delete Please select a MAC address from the list, then click ‘Delete’ button to remove it. Remove All Delete all MAC addresses in the list.
3.4 Connection t able If you want to see the list of all wireless client s connected to this access point, please follo w the following instructions: 1.
Here are descriptions of every fields: MAC Address Displays the MAC address of this wireless client. AID The serial number of this wireless connection.
3.5 Event Log This software access point will log all wireless-related activities as a log. Y ou can follow the following instructions to view the content of the event log: 1. Right-Click Ralink configuration utility icon, and select ‘Launch Config Utilities’ 2.
3.6 St atistics If you want to know detailed information about how your software access point works, you can follow the following instructions to vi ew the statistics of the access point: 1. Right-Click Ralink configuration utility icon, and select ‘Launch Config Utilities’ 2.
Chapter 4: APPENDIX 4.1 T roubleshooting If you encounter any problem when you’re usin g th is wireless network card, don’t pani c! Before you call your dealer of purchase for help, pleas e check .
3. Y ou have to input correct passphrase / security key to connect an access point with encryption. Please contact the owner of access point to ask for correct passphrase / security key . 4. The access point you wish to connect only allows network cards with specific MAC address to establish connection.
4.2 Glossary 1. What is the IEEE 802.1 1g standard? 802.1 1g is the new IEEE standard for high- speed wireless LAN communications that provides for up to 54 Mbps data rate in the 2.4 GHz band. 802.1 1g is quickly becoming the next mainstream wireless LAN technology for the home, office and public networks.
6. What is BSS ID? A specific A d hoc LAN is called a Basic Service Set (BSS). Computers in a BSS must be configured with the same BSS ID. 7. What is WEP? WEP is Wired Equivalent Privacy , a dat a privacy mechanism based on a 40 bit shared key algorithm, as described in the IEEE 802 .
(ignored) by most narrowband receivers. 13. What is S pread S pectrum? S pread S pectrum technology is a wideband radio frequen cy technique developed by the military for use in reliable, secure, missi on-critical communication systems. It is designed to trade off bandwid th efficiency for reli ability , integrity , and security .
デバイスCNET CWP-905の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
CNET CWP-905をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCNET CWP-905の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。CNET CWP-905の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。CNET CWP-905で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
CNET CWP-905を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCNET CWP-905の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、CNET CWP-905に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCNET CWP-905デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
