3Mメーカー1420EZの使用説明書/サービス説明書
ページ先へ移動 of 20
3M ™ Dynatel ™ 1420EZ Writer Operator’ s Manual December 2008 78-9000-0120-3-A 3.
2 78-9000-0120-3-A Congratulations on your purchase of the 3M ™ Dynatel ™ Model 1420EZ Writer . The Dynatel ™ 1420EZ Writer is designed to write up to ten 3M ™ iD Ball Markers, ten iD Near Surface Markers or ten iD Disk Markers in one simple step.
78-9000-0120-3-A 3 Safety Information Please read, understand and follow all safety information contained in these instructions prior to the use of the 3M ™ Dynatel ™ 1420EZ Writer .
4 78-9000-0120-3-A Introduction The Dynatel ™ 1420EZ Station consists of the following items; Dynatel 1. ™ 1420EZ Stand: Writing stand that can hold up to ten Ball or ten Near Surface or ten Disk iD-Markers in pre- allocated slots. Dynatel 2. ™ 1420EZ Writer: iD-Marker reading and writing unit Dynatel 3.
78-9000-0120-3-A 5 Dynatel ™ 1420EZ Writer - Batter y Installation 8 “AA ” Alkaline Batteries 1. T wist ca p to open batter y compartment. 2. Slide batter y compartment out of handle.
6 78-9000-0120-3-A Dynatel ™ 1420EZ Writer Operation Dynatel ™ PCT ools Download and Installation The Dynatel ™ PCT ools software must be downloaded and installed on the laptop/desktop PC from the 3M website at www .
78-9000-0120-3-A 7 Creating iD-Marker T emplates using Dynatel ™ PCT ools A data template must be created in Dynatel ™ PCT ools for writing iD-Markers with the Dynatel ™ 1420EZ Writer . The full User Guide for Dynatel ™ PCT ools is av ailable for download at www .
8 78-9000-0120-3-A Follo wing is a Read/Write tab screen shot that highlights the different setups that can be configured by the user . T emplate Log Data Markers in the fixture Options T o write dat.
78-9000-0120-3-A 9 Select Overwrite Old Marker Data, Permanently Lock Marker Data or both. If “Permanently Lock Marker Data” is − selected, the following dialog box appears: NO TE: Choosing to P ermanently Lock Marker Data is irreversible. Once the data is locked it can not be overwritten.
10 78-9000-0120-3-A Read or Read/Write iD-Markers Once the Read/Write tab set-up is completed (previous section), two options are available; Read Only: • This option only reads the iD-Markers and then makes available any information that was previously programmed in the iD-Markers.
78-9000-0120-3-A 11 Read Only Button When the Read Only button is selected, the Dynatel ™ 1420EZ Writer reads all of the iD-Markers that are in the Dynatel ™ 1420EZ Stand and then sends the results back to Dynatel ™ PCT ools.
12 78-9000-0120-3-A The • “Blank” Marker column displays; − (check mark) if there is not any previously written data present in the iD-Markers. − (warning symbol with a magnifying glass) if previously written data is present in the iD-Markers.
78-9000-0120-3-A 13 The written iD-Marker data is then displayed as shown in the following screen shot: Was “Blank” Marker Heading Written and verified The information from each written marker is displayed in the Marker Data / Status section.
14 78-9000-0120-3-A The • T otal Mark ers Written box shows the total count of all the iD-Markers that were read, written and verified successfully . If this count matches the T otal Markers Read box value, then it is highlighted in green. − If the count does not match, then it is highlighted in red.
78-9000-0120-3-A 15 ERR OR 3: Lock Data: The iD-Marker data is locked. REMED Y : The iD-Marker data was pre viously locked, therefore it cannot be rewritten.
16 78-9000-0120-3-A Read and Write Failures ERR OR: When the Read and Write button is clicked, and iD-Markers are read with any of the above errors, the follo wing error message may be displayed and the write process is stopped. REMED Y : See appropriate remedy in Read F ailures section abov e.
78-9000-0120-3-A 17 T otal Number of Markers in Fixture Error ERR OR: If the Read Only button or Read and Write button is clicked, and there is no entry in the Enter the No.
18 78-9000-0120-3-A Miscellaneous Errors ERR OR: If an attempt is made to read or write to iD-Markers and the Dynatel ™ 1420EZ Writer is not po wered on or the incorrect comport is selected, one or both of the following dialog boxes will appear: REMED Y : Power On the Dynatel ™ 1420EZ Writer or verify that the correct comport is selected.
78-9000-0120-3-A 19 Specifications Dynatel ™ 1420EZ Writer Frequencies / iD-Markers Power , T elephone, Gas, Water , W aste Water , Communication (CA TV), General Purpose Weight with Batteries 4 lbs (1.
This p roduct is in accor dance wit h the requirements of the European directive 99/5/EC 3M and Dynatel are trademarks of 3M Compan y . Important Notice All sta tements, technical informa tion, and recommendations related to 3M’ s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed.
デバイス3M 1420EZの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
3M 1420EZをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこには3M 1420EZの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。3M 1420EZの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。3M 1420EZで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
3M 1420EZを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又は3M 1420EZの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、3M 1420EZに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわち3M 1420EZデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。