CombiメーカーVictoria 8850の使用説明書/サービス説明書
ページ先へ移動 of 20
V ictoria ™ 8850 Series Instruction Manual Victoria ™ Convertible Car Seat Correct installation and use can be a matter of Life or Death! Read and understand these instructions before using this car seat. • Certified for use in motor vehicles and aircraft.
1 Section 1 - T able of Contents Section 1. T able of Contents.................................... 1 Section 2. W arnings.............................................. 2 Section 3. Proper Use Check List............................ 3 Section 4. Victoria ™ Car Seat Parts.
• Proper use is required. Read and understand instructions and car seat labels. • Securely install car seat with LA TCH System or vehicle seat belt and top tether strap. • Snugly adjust harness around child. • Harness covers MUST be used when forward-facing.
5 Section 5 - Use Recommendations Height and Weight Limits: This child restraint is designed for use only by children whose: -W eight is between 5 and 40 pounds (2.
7 Section 6 - Selecting A V ehicle Seating Location The National Highway T raffic Safety Administration (NHTSA) alerts vehicle owners that according to accident statistics, children up to age 12 are safer when properly restrained in the rear seating positions rather than the front seating positions.
9 Section 7 - LA TCH System (fig. b) (fig. a) 2 3 2 1 LA TCH System On This Car Seat: The LA TCH System on the Victoria Car Seat consists of a lower anchor belt with lower anchor connectors and for forward-facing use, a top tether strap with tether hook (fig.
11 •L AT CH belt MUST stay tightly adjusted around car seat at all times. • Only use the car seat LA TCH System in vehicle seating locations designated by the vehicle manufacturer for use with LA TCH and that have an anchor spacing of 1 1 inches (280 mm).
Storage Of Lower Anchor Belt And Connectors: When not using the LA TCH System, store the lower anchor belt and hook-on connectors by removing lower anchor belt and connectors from rear-facing belt path and snapping hook-on connectors onto LA TCH connector storage locations on back of base (fig.
15 Thread vehicle lap belt or vehicle lap and shoulder belts through the rear-facing belt path in the seat (fig. b) : - Thread vehicle seat belt through rear-facing belt path openings identified by the blue “Belt Here” arrows. - Buckle seat belt and remove any slack in the vehicle seat belt.
17 9b.Forward-facing Installation W ith LA TCH Refer to vehicle owner ’s manual to identify the seating locations with LA TCH System. Select the seating location to be used and locate the vehicle lower anchors at the seat bight and top tether anchor (fig.
19 Connect lower anchor connectors to vehicle lower anchors. - With hook-on connector opening facing down , position the opening of the connector over the vehicle lower anchor . Push down and then pull out on the connector to lock it onto the vehicle anchor (fig.
21 Refer to vehicle owner ’s manual to identify the seating locations which can be used with a car seat. Check for specific instructions for car seat use. After selecting a seating location, if vehicle seat back is adjustable, adjust seat back into most upright position.
23 Removal Of Car Seat Installed With V ehicle Seat Belt: T ip belt adjuster to loosen top tether strap (fig. g) . Depress retainer spring and unhook tether hook from vehicle top tether anchor (fig. h) Position seat in recline position #1. Unbuckle vehicle seat belt.
25 Loosen harness: - Grasp shoulder harness strap BELOW harness cover . -W hile pressing on harness adjuster lever , pull out on shoulder harness strap. IMPORT ANT : DO NOT pull out on harness strap covers! Harness strap covers are secured to the seat back and pulling on them will not allow you to lengthen the harness straps.
27 1 1b. Changing Shoulder Harness Positions: Rear-facing - Shoulder harness straps must be through shoulder harness slots at or just below child’s shoulders. - Only use middle or lowest harness strap slots for rear-facing. Forward-facing - Shoulder harness straps must be at or above shoulders and harness covers MUST be used.
29 1. Recline seat into rear-facing, fully reclined position #1. 2. Positioning and attachment of harness covers: NOTE: If using car seat without harness covers, skip to step #4. a. Position harness cover with rubber surface down and folded edge toward outside of car seat ( fig.
31 1 1c. Infant Insert: •T o prevent ejection: - Shoulder belts MUST be through belt slots in infant insert. - For proper harness fit, infant insert MUST be used for small infants. • Discontinue use of infant insert when: - Shoulder belts become too short to fit infant.
33 Manually adjustable lap belts (fig. c) normally will hold a car seat tightly . However , in some cases, the locking latch plate on some seat belts may slip and loosen if positioned at a certain angle. If this happens, flip latch plate over (fig. c) and re-buckle.
35 Section 13 - Rear-facing Belt Lock-off • Failure to use the belt lock-off where required will result in car seat not being securely held in place.
37 Section 16 - Registration Information Child restraints (car seats) could be recalled for safety reasons. Y ou must register this restraint to be reached in a recall.
デバイスCombi Victoria 8850の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Combi Victoria 8850をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCombi Victoria 8850の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Combi Victoria 8850の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Combi Victoria 8850で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Combi Victoria 8850を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCombi Victoria 8850の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Combi Victoria 8850に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCombi Victoria 8850デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。