Aga RangesメーカーFired Earthの使用説明書/サービス説明書
ページ先へ移動 of 12
Floor Tiling Installation Guide Ancillar y Products A full range of high quality fixing and sealing products, researched and developed to meet Fired Earth standards, are available for both professional and DIY use. Read the instructions on the packaging of Adhesives, Grouts and Sealants very carefully .
Floor Tiling Installation Guide Contents Substrates 4 Planning 6 Fixing 7 Cutting 8 Sealing 9 Grouting 1 0 Terracotta Tiles 1 1 Presealed Terracotta, Geometric, Roman Mosaic and Encaustic Tiles 13 Sla.
5 Substra tes If your tiling is to last, it is essential that the surface onto which the tiles are to be laid is sound. Careful consideration must be given to the floor surface to confirm that the surface is level, clean, dry , free of dust, grease and any loose material.
Step 4. When tiling commences you should start at point ‘X’, so check that the lines you have marked make a perfect right angle and the side line runs parallel to the centre line. Grout joints The width of grout joints will vary between 3–12mm. Large joints will be necessary on rustic tiles such as terracotta and slate.
9 8 C utting Due to the thickness and make-up of the majority of Fired Earth floor tiles, it is recommended that either a diamond cutter or an angle grinder is used to cut the tiles. Water cooled diamond cutters are available from tool hire shops. Please wear suitable protective eyewear and protective clothing when cutting tiles.
Grouting Grouting refers to the process of filling the spaces between the individual tiles and thus completing the floor surface. Before grouting can commence, the adhesive used must have cured, which usually takes between 12–24 hours for Fired Earth Floor Adhesive* and 3 hours for Fired Earth Fastset Adhesive*.
P ammets because salt pits cannot be 'blended in' without the use of wax polish. Maintenance Terracotta floors should be swept or vacuumed regularly to remove all loose dirt.
15 14 Slate and Lubelska Bricks Sealing Before grouting apply one or two coats of Fired Earth Stone Shield* using a clean, fluff-free cloth. Allow approximately 2 hours between applications and do not apply more sealer than can be fully absorbed by the tiles within 20 minutes.
17 P orcelain and G lass Tiles These tiles do not require any sealing or finishing products. After grouting, the tiles should be polished with a soft, clean cloth to remove any remaining grout film. The grout can be sealed with MN Stain Stop* to prevent staining.
Substrate Sand and Cement Screed Concrete/Brickwork Timber Floorboards (sound and secure) Timber Floorboards overlaid with WBP Plywood (min depth 18mm) Timber Floating Floors Quarry , Clay , Glazed Ti.
Substrate Sand and Cement Screed Concrete/Brickwork Timber Floorboards (sound and secure) Timber Floorboards overlaid with WBP Plywood (min depth 18mm) Timber Floating Floors Quarry , Clay , Glazed Ti.
Product Sealant Finish Cleaner Maintenance Terracotta (inc. Reclaimed terracotta) Fired Earth Linseed Sealer* Wax paste (high protection/high maintenance/ colour enhancer) Cotto Rapid (low maintenance.
デバイスAga Ranges Fired Earthの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Aga Ranges Fired Earthをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAga Ranges Fired Earthの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Aga Ranges Fired Earthの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Aga Ranges Fired Earthで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Aga Ranges Fired Earthを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAga Ranges Fired Earthの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Aga Ranges Fired Earthに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAga Ranges Fired Earthデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
