Compatible Systemsメーカー900iの使用説明書/サービス説明書
ページ先へ移動 of 44
MicroRouter 900i Installation Guide Comp atible System s Corpor ation 4730 W alnut Street Suite 1 02 Boulde r , Colo rado 80301 303- 444- 9532 800- 356- 0283 http://www .
MicroRou ter 900i In stallat ion Gui de, V ersio n 3.0 Copyri ght© 1999 , Compati ble Sy stems Co rporati on All rights reserved. RISC Router and Comp atiV iew are trademarks of Compatible System s Co rpor ation. Other trad emarks ar e the property of their respective holders.
iii Chapter 1 - Introduction 1 A BOU T THE M ICRO R OUTER 900 I 1 A N OTE A BOUT O N -D EMAND I NTERNETWORKING 1 M ICRO R OUTER 900 I I NSTALLA TION O VERV IEW 1 Chapter 2 - Getting Started 2 Chapter .
iv Conne cting an Out-o f-Band Mana gement Console 11 Power ing Up th e Ro uter 11 Chapter 4 - CompatiView Software Installation 13 CompatiView for Win dows 13 System Requ irements 13 Installin g and .
v IP Prot ocol 24 Required for IP 24 Required for IP Numbere d Interface 24 Required for IP Unn umbered Interface 24 Suggested fo r IP 24 S AVIN G A C ONFIGURATION F ILE TO F LASH ROM 25 Appendi x A -.
vi.
Cha pter 1 - In tr odu ctio n 1 Chapter 1 - Introduction About the MicroRouter 900i Congratul ations o n your pur chase of the Mi croRouter 90 0i Ethernet to Internet r outer .
2 Cha pter 1 - In tr odu ctio n In shor t, the installation steps are: 1. Install the MicroRouter hardware and connect it to a line commu- nication dev ice (inclu ding a mod em, 56K CSU/ DSU, or ISDN T er- minal Adapter) . 2. Select the managemen t met hod you wi sh to use w ith the rou t er .
Cha pter 1 - In tr odu ctio n 3 Appendices This part of the manual in cludes additional infor mation that might be of interest to you such as technical specifications, default settin gs (includi ng the de fault factory password) an d instru ctions for down- loading curren t soft ware.
.
Chapter 2 - Getting St arted 5 Chapter 2 - Getting Started A Few Notes Please Read The Manuals The manual s included with your Micro Router 900i contain s ome very important information ab out the MicroRouter 900 i and local and wide area network ing in gen eral.
6 Chapter 2 - Getting St arted What You Will Ne ed To Ge t Started Before con necting the MicroRouter 900i, please check the list below to make sure that you have received all of the items that are supplied with the MicroRouter 900i package.
Chapter 2 - Getting St arted 7 Thick Ethernet T o connect the router ’ s Ethernet port to a s tandard (thick) Ethern et cable you will need a transceiver cable connection at the correct location on your Ethernet cable. The transceiver cable will attach directly to the DB-15 connector o n the router .
8 Chapter 2 - Getting St arted The MicroRout er 900i includes o ne DIN-8 to DB-25 RS-2 32 sync/async data cab le. This cable supports RS-23 2 asynchronou s modems, sy nchronous leased and switc hed-56K CSU/ DSU ’ s, and North American ISDN T erminal Adapters .
Chapter 3 - Network Installatio n 9 Chapter 3 - Network Installation 900i MicroRouter Back Panel This section of th e manual describes ho w to connect the MicroRouter 900i to your Eth ernet network an d your wide area commu nications device. In summ ary , the steps for ins tallation are: 1.
10 Chapter 3 - Network Installatio n For wall mounting, follow the instruction s included with the wall-mount bracket ki t. Connecting the Router to the Ethernet For thic k or thin Ethernet netw orks, you s hould hav e installed your Ethernet cabling b efore you inst all the MicroRouter 900i.
Chapter 3 - Network Installatio n 11 r outer must first be configu r ed for sy nchr onous operat ion befor e connecting to the device. S ee Chapter 6 - Basic C onfiguratio n Guide for configura tio n information . Y ou may sel ect either dial-o n-demand, al ways up (i.
.
Chapter 4 - CompatiVie w Software Installation 13 Chapter 4 - CompatiView Software Installation All of the routers in Co m patible Systems ’ i nternetworking and V PN families, including all RISC Router and MicroRou ter models, can be managed fro m a single GUI manageme nt platform cal led Com patiV iew .
14 Chapter 4 - CompatiVie w Software Installation which it should locate Comp atiV iew and its associated files and data- base su bdir ecto ry . Once the installation is compl ete, double-click on the CompatiV iew icon to o pen the pr ogram.
Chapter 5 - S etting Up Comma nd Line Management 15 Chapter 5 - Setting Up Command Line Management The command line interface allows you to configure and monitor the router in-band via T elnet or out-of-band with a terminal connected to the MicroRouter 900 i ’ s Console inter face.
16 Chapter 5 - S etting Up Comma nd Line Management ernet interface. Y ou can then do the following: 1. Set the host ’ s IP address to 198.41.1 2.2, with a Cl ass C subnet mask (25 5.255.255. 0) and then T elnet to 198 .41.12.1. 2. Enter the default password letmein at the pass word prompt .
Chapter 5 - S etting Up Comma nd Line Management 17 using t he IP trans port proto col), or an ywhere on your ne twork (if us ing the IPX transport pr otocol) . Instru ctions fo r these two met hods are gi ven in Chapter 4 - Compa tiV iew S oftware Installation .
..
Chapter 6 - Basic Configurat ion Guide 19 Chapter 6 - Basic Configuration Guide This chapter briefly discusses the majo r parameters th at m u st be set in order to us e the router .
20 Chapter 6 - Basic Configurat ion Guide IP Protoc ol Required fo r IP These parameters set the b asic address character istics of the interface. They prov ide enough info rmation for ano ther IP node to find the inter- face (such a s a T elnet client), b ut not enough informat ion for rou ting to take place.
Chapter 6 - Basic Configurat ion Guide 21 parameters will depend o n the line comm unications d evice you are usin g. v Note : Frame Relay and SMDS ar e pr esently supported in the Micr oRou ter 900i o nly via syn chr onous operatio n. An external clock signal is genera ted for Frame Relay .
22 Chapter 6 - Basic Configurat ion Guide Suggested fo r Dial-On-Deman d Operation This mode of operation is only supported on the W AN RS-232 inter- face.
Chapter 6 - Basic Configurat ion Guide 23 operati on when you ar e connecting to another C ompatible Systems r out e r at t he ot he r e nd of th e lin k . Frame Relay Configuration This section covers the settings requ ir ed for Fram e Relay operation of the MicroRouter 90 0i W AN interfaces.
24 Chapter 6 - Basic Configurat ion Guide TB: Use configure and set the DLCI keyword in the Frame Relay W AN 0 section. IP Protoc ol Required fo r IP There are two ways to set up Frame R elay . One is to set th e W AN inter- face as a “ numbered interfa ce.
Chapter 6 - Basic Configurat ion Guide 25 TB : Use configure and set either the RIPV ersion keyword or th e OSPFEnabled k eyword in th e IP W AN 0 section.
.
Appendix A - Shippi ng Defaults 27 Appendix A - Shipping Defaults Default Password • letmein Ethernet Port IP Defaults • On • Address: 198.41.1 2.
.
Appendix B - Connector and Cab le Pin Outs 29 Appendix B - Connector and Cable Pin Outs Pin Outs f or DIN-8 to RS-232 Data Cable (DCE/Male) Notes: 1. DC D must be sup ported in o rder for t he router to sense a compl eted connection. 2. Tx Clock dir ection is determined by an internal jump er .
30 Appendix B - Connector and Cab le Pin Outs Notes: 1. This cable is a null-modem DTE-to-DTE cable. 2. Becaus e it is a null-modem cable, it can be connected “ back-to-back ” with a DCE/Male data cable in order to cr eate a router -to-rout er test connection cab le.
Appendix C - Light P atterns and Test Sw itch Settings 31 Appendix C - Light Patterns and Test Switch Settings MicroRo uter 900 i Li ght Patte r ns The MicroRout er 900i uses a nu mber of ligh t patterns o n its fron t LED bar to in dicate operat ing cond itions.
32 Appendix C - Light P atterns and Test Sw itch Settings MicroRouter 9 00i Switch Settings M Caution: Settings marked with an as terisk may erase you r Flash ROM. Please do not use these settings w ith out first co ntacting Compatible Systems T echnical Support.
Appendix D - Downloading Software F rom Compatible Systems 33 Appendix D - Downloading Software From Compatible Systems W e make the latest versions of operatin g sof twar e for all Co mpatible Systems products avail able at our W eb site. The lat est versio n of CompatiV iew management s oftware is als o available.
..
Appendix E - T erms and Cond itions 35 Appendix E - Terms and Condition s Compatible S ys tem s Corporation (Com patible Systems) offers to sell only on the condition that Cu sto mer ’ s acceptance is expressly limited to Compat- ible Systems ’ terms and conditions of sale.
36 Appendix E - T erms and Cond itions T o obtai n service un der this W arranty , the Customer (or subsequ ent pur- chaser , if applicab le) must follow the procedures outlined belo w , u nder “ Product Retur n P olicy . ” THE W ARRANTIES SET FOR TH IN THESE TERMS AND CONDI- TIONS ARE IN LIE U OF ALL OTHER W ARRANTIES, EXPRESSE D OR IMPLIED.
Appendix E - T erms and Cond itions 37 ber of each item being returned; (c) original Compatible Systems Sales Agreement number; and (d) any special instructions. Upon receipt of this information, Com pati ble Systems will issu e an R M A ( “ Return Material Authorization ” ) number and any required U.
38 Appendix E - T erms and Cond itions.
デバイスCompatible Systems 900iの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Compatible Systems 900iをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCompatible Systems 900iの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Compatible Systems 900iの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Compatible Systems 900iで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Compatible Systems 900iを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCompatible Systems 900iの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Compatible Systems 900iに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCompatible Systems 900iデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
