Craftsmanメーカー706.59669の使用説明書/サービス説明書
ページ先へ移動 of 18
706.596680 706.596690 6-Drawer Chest 7-Drawer Roll-A-Way Owners Manual Craftsman 7-Drawer AXS TM Roll-Away Craftsman 6-Drawer AXS TM Chest Section 1612 1613 1614 1615 1616 1617 1618 1623 1624 1625 Des.
i CRAFTSMAN°i CHEST TOP AND FACIA PARTS REPLACEMENT S Facia Chest Top with light Information Center CHEST TOP INSTALLATION AND REMOVAL (With task light) Tools Required: 3/8" Wrench Chest Top Removal • Disconnect power from unit. • Remove enough drawers to reach the top back inside of the unit.
INFORMATION CENTER INSTALLATION AND REMOVAL Tools Required: Screwdriver, Crosstip Tape Removal • Disconnect power from the unit. • Remove enough drawers to reach the retaining screw under the information center. (See removing and installing drawers.
CONNECTING POWER • Ensure that the unit and power cord are clean and dry. • insert the round end of the power cord connector into the jack in the back of the unit. • Plug the cord into an appropriate electrical outlet. Fuse block Jack Cord REMOVING AND INSTALLING DRAWERS: • Empty the drawer.
I CRAFTSMAN°I DRAWER AND WORK SURFACE PARTS REPLACEMENT SLIDE REPLACEMENT Tools Required: Drill 5/32" Drill bit Rivet gun Removal • Remove drawer or work surface from unit. (See drawer and work surface installation and removal.) • Carefully drill out rivet holding slide drawer member to drawer or work surface.
DRAWER AND WORK SURFACE REPLACEMENT DRAWER FRONT INSTALLATION AND REMOVAL Tools Required: Drill 5/32" Drill bit Rivet gun Crosstip screwdriver Removal • Remove drawer or work surface from unit. (See Drawer and Work surface installation and removal.
DRAWER AND WORK SURFACE INSTALLATION AND REMOVAL Note: For pull out work surface without task light, follow drawer removal instructions. DRAWER • Empty the drawer. • Fully extend the drawer. Release Lever Style - Lift or lower (depending on the slide) the release lever on both sides, (this allows the slides to ride over the stops.
I CRAFTSMAN°I BOTTOM REPLACEMENT Tools Required: Socket Wrench 5/16" Socket Removal • Disconnect power from the unit. • Remove contents from drawers. • Carefully lay the chest on its back. Take care to prevent scratches or damage to the unit.
I CRAFTSMAN°I TOP, WIRING HARNESS, HARNESS GROMMET Parts Replacement Roll-away top WIRING HARNESS REPLACEMENT HARNESS GROMMET REPLACEMENT Tools Required: 3/8" Wrench WIRING HARNESS AND HARNESS GROMMET REMOVAL • Disconnect power from unit. • Remove pull out work surface and enough drawers to reach the top back inside of the unit.
TOP INSTALLATION AND REMOVAL Tools Required: Screwdriver, Crosstip Roll-away top removal • Disconnect power from unit. • Remove pull out work surface. (See drawer and work surface installation and removal.) • Remove enough drawers to reach the top back inside of the unit.
I CRAFTSMAN°I CHEST TOP WITHOUT TASK LIGHT Tools Required: Screwdriver, Crosstip Chest top removal • Disconnect power from unit. • Remove pull out work surface. (See drawer installation and removal.) • Remove enough drawers to reach the top back inside of the unit.
I CRAFTSMAN°I TASK LIGHT REPLACEMENT Tools Required: Screwdriver, Crosstip Removal • Disconnect power from the unit. • Fully extend task light assembly. • Make note of light orientation. • Remove (6) mounting screws to remove light. • Unplug light.
I CRAFTSMAN°I LOCKING SYSTEM Parts Replacement Actuator Channel Actuator Rod Bracket ACTUATOR ROD AND ACTUATOR CHANNEL REPLACEMENT ACTUATOR ROD AND ACTUATOR CHANNEL REMOVAL • Disconnect power from the unit. • Remove work surface (Roll-away only).
ACTUATOR ROD BRACKET INSTALLATION AND REMOVAL Removal • Disconnect power from unit. • For roll-aways, remove work surface. (See drawer and work surface installation and removal. • Remove enough drawers to reach the top back inside of the unit. (See Drawer and Work surface installation and removal.
CHEST TOP INSTALLATION AND REMOVAL (With task light) Tools Required: 3/8" Wrench Chest Top Removal • Disconnect power from unit. • Remove enough drawers to reach the top back inside of the unit. (See Drawer installation and removal.) • Push actuator rod to back of unit to disconnect from back of lock.
I CRAFTSMAN°I LOCK REPLACEMENT Removal • Disconnect power from unit. • For roll-aways, remove work surface. (See drawer and work surface installation and removal • Remove enough drawers to reach the lock retaining clip behind the lock. • Remove lock retaining clip.
I CRRFT.TMRN°J STRIKER REPLACEMENT Tools Required: Screwdriver Removal • Remove drawer from unit. • Turn drawer upside down. • Depress (2) detents. Push striker in to remove. Depress detents Drawer installation and removal • Emptythe drawer. • Fully extend the drawer.
I CRAFTSMAN°I DRAWER FRONT REPLACEMENT Tools Required: Crosstip screwdriver Removal • Remove retaining screw(s). • Slide drawer front assembly as indicated to unhook mounting tabs. • Pull out to remove. Installation • Position drawer front on drawer assembly.
デバイスCraftsman 706.59669の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Craftsman 706.59669をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 706.59669の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 706.59669の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 706.59669で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 706.59669を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 706.59669の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 706.59669に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 706.59669デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。