Craftsmanメーカー917.273062の使用説明書/サービス説明書
ページ先へ移動 of 68
Owner's Manual ICRAFTSMAN°I 20.0 HP ELECTRIC START 50" MOWER AUTOMATIC GARDEN TRACTOR Model No. 917.273062 • Safety • Assembly ° Operation ° Maintenance ° Repair Parts CAUTION: Read and follow all Safety Rules and Instructions before operating this equipment.
Warranty ............................................... 2 Safety Rules ......................................... 3 Product Specifications .......................... 6 Assembly .............................................. 9 Operation ...............
IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. I. GENERAL OPERATION • Read, understand, and follow all instructions in the manual and on the machine before starting.
Ill. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. . Keep children out of the mowing area and under the watchful care of another responsible adult.
* Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. * Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. o If machine stops while going uphill, disengage blades, shift into reverse and back down slowly.
PRODUCT SPECIFICATIONS GASOLINE 3.5 GALLONS CAPACITY UNLEADED AND TYPE: REGULAR OILTYPE SAE 10W30 (API-SF/SG/SH): (ABOVE 32°F) SAE 5W-30 (BELOW 32°F) OIL CAPACITY: W/FILTER: 4.5PINTS W/O FILTER: 4.0PINTS SPARK PLUG: CHAMPION (GAP: .030") RC12YC GROUND FORWARD: 5.
Steering Wheel © Steering Wheel Insert Steering Sleeve Steering Sleeve Extension Seat (1) Washer @ 17/32 x 1-3/16 x 12 Gauge _(1) Knob Mower (4) Retainer Springs (single loop) (1) Shoulder Bolt 5/16-18 (2) Front Link_ (3) Retainer Springs (double loop) Gauge Wheels (2) Shoulder Bolts _(2) Wheels (2) Centedock Nuts (2) Washers 3/8 x 3/4 x 14 Ga.
Video Cassette Slope Sheet Keys (2) Keys Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely.
BEFORE REMOVING TRACTOR FROM SKID ATTACH STEERING WHEEL 1. Remove hex bolt, lock washer and large flat washer from steering shaft. 2. Position front wheels of the tractor so they are pointing straight forward. 3. Slide the steering sleeve over the steering shaft.
TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls) 1. Press lift lever plunger and raise attachment lift lever to its highest position.
INSTALL MOWER AND DRIVE BELT Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage parking brake. 1. Cut and remove ties securing anti- sway bar and belts. Swing anti-sway bar to left side of mower deck.
CHECKTIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. = Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. t FAST BATTERY CAUTION OR REVERSE FORWARD SLOW WARNING ENGINE ON ENGINE OFF OIL.
KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs, We recommend a wide vision safety mask over spectacles or standard safety glasses.
The cutting height range is approximately 1-1/2" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.
TO TRANSPORT When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor. 1. Raise attachment lift to highest position with attachment lift control.
TO START ENGINE When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. 1. Be sure freewheel control is in the transmission engaged position. 2. Sit on seat in operating position, depress clutch/brake pedal and set parking brake.
4. Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times, NOTE: During this procedure there will be no movement of drive wheels.
FILLIN DATES ._,_y'_ _,_ e_ ASRE ULARSERVIoE OU COMPLETE ---- OA TES Check Brake Operation _ Check Tire Pressure I1_ Check Operator Presence and T Interlock Systems If a Check for Loose Fasteners.
TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be ad- justed. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual).
• Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.
CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.
_IbCAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place motion control lever in neutral (N) position. 3. Place attachment clutch in "DISENGAGED" position. 4. Turn ignition key "OFF" and remove key.
o If adjustment is necessary, make adjustment on one side of mower only. ,, To raise one side of mower, tighten lift link adjustment nut on that side. • To lower one side of mower, loosen lift link adjustment nut on that side. NOTE: Each full turn of adjustment nut will change mower height about 3/16".
Left Hand Cover Screws Idler Pulleys Primary Idler Arm Spring Electric Clutch Pulley Bolt in Left Hand Mandrel Mower Drive Belt Belt Keepers Housing TO REPLACE MOWER BLADE DRIVE BELT Park the tractor on level surface. Engage parking brake. 1. Remove mower drive belt (See "TO REPLACE MOWER DRIVE BELT" in this section of this manual), 2.
1. Make sure attachment clutch and ignition switches are in "OFF" position. 2. Adjust the three nylon Iocknuts until space between clutch plate and rotor measures .
6. Place belt around clutching idlers as shown, making sure to route belt inside of all belt keepers. 7 Check to be sure belt is positioned correctly and is on proper side of all belt keepers.
TO REMOVE WHEEL FOR REPAIRS FRONT WHEEL - 1. Block up axle securely. 2. Remove axle cover, retaining ring and washers to allow wheel removal. 3. Repair tire and reassemble. 4. Replace washers and snap retaining ring securely in axle groove. 5. Replace axle cover.
TO REPLACE HEADLIGHT BULB 1. Raise hood. 2. Pull bulb holder out of the hole in the backside of the grill. 3. Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
TO ADJUST CHOKE CONTROL The choke control has been preset at the factory and adjustment should not be necessary, check adjustment as de- scribed below before loosening cable. If adjustment is necessary, proceed as follows: 1. With engine not running, move choke control (located on dash panel) to full choke position.
Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. _lb CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Will not start Hard to start Engine will not turn over Engine clicks but will not start Loss of power 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. 4. Bad spark plug. 5. Dirty air filter.
TROUBLESHOOTING CHART CAUSE CORRECTION 3. PROBLEM Loss of power (continued) Excessive vibration Engine continues to run when operator leaves seat with attachment clutch engaged Poorcut-uneven Mower blades will not rotate Build-up of grass, leaves and trash under mower, 4.
TROUBLESHOOTING CHART PROBLEM Poor grass 1. discharge 2, 3. 4. 5. 6, 7. 8. 9. Headlight(s) not working (if so equipped) Battery will not charge Loss of drive Engine "backfires" when turning engine "OFF" CAUSE CORRECTION Engine speed too slow.
NOTES 36.
SCHEMATIC TRACTOR - MODEL NUMBER 917,273062 BATTERy IGNITION E E 3WITCH SOLENOID RED STARTER BLACK t I D PTO (DISENGAGED) t E LECT_a_£_CkuzcH t CLUTCH / BRAKI I (PEDAL UP) ......... , RE0 E SEAT SWITCH (NOT OCCUPIED) ..... I OPERATOR PRESENCE RELAY#_ .
TRACTOR -- MODEL NUMBER 917.273062 ELECTRICAL 22 11 27 26 16 29 33 52 / I // // / // 38.
TRACTOR -- MODEL NUMBER 917.273062 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 144927 Battery 2 74760412 Bolt Hex Head 1/4-20 x 3/4 8 7603J Tray, Battery 10 145211 Bolt 1/4-20 x 7.
TRACTOR - MODEL NUMBER 917.273062 CHASSIS AND ENCLOSURES 37 147 _140 147 122 150 122 147 122 / 18" 122 28 21 52 17 16 56 100 ! 68 17 70 42 39 17 4O.
TRACTOR -- MODEL NUMBER 917.273062 CHASSIS AND ENCLOSURES KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 150253 Rail, Frame RH 52 STD541431 2 140506 Drawbar, Gt 56 154914 4 73800700 Nut, Lock Hex 7/1.
TRACTOR - MODEL NUMBER 917.273062 GROUND DRIVE 76 81 42 33 9 7 _ / 109 , i 6 38 46 36 / 100 69 56 72 2 54 15 42.
TRACTOR -- MODEL NUMBER 917.273062 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 Transaxle (See Breakdewn) 71 151179 Hydro Gear 222-3010 72 STD541431 2 7070E Key 1/4 x 2.
TRACTOR - MODEL NUMBER 917.273062 STEERING 14 d! 1313 36 44.
STEERING TRACTOR -- MODEL NUMBER 917.273062 KEY PART NO. NO. DESCRIPTION 1 159944X428 2 137094 3 6855M 4 161849 5 161848 6 6266H 7 121748X 8 12000029 9 121232X 10 74781044 11 136518 12 73901000 13 121.
TRACTOR - MODEL NUMBER 917.273062 ENGINE 18 16 21 15 26 17 37 / 39 I _ 45 39 12 42 43 19 7 48 38 29 SPARK ARRESTER KIT I 46.
ENGINE TRACTOR -- MODEL NUMBER 917.273062 KEY PART NO. NO. DESCRiPTiON 2 161063 5 13200300 7 151396 8 121361X 9 150828 10 105432X 11 140923 12 143996 15 151346 16 109227X 17 106082X 18 161493 19 13290.
TRACTOR -- MODEL NUMBER 917.273062 SEAT ASSEMBLY I 19 12 21 KEY PART NO, NO, 1 140124 2 140551 3 140675 4 127018X 5 145006 6 STD541437 7 124181X 8 171877 10 155925 12 121246X 13 121248X DESCRIPTION Seat Bracket, Pivot Seat Strap, Fender Bolt, Shoulder 5/16-18 x .
DECALS TRACTOR - MODEL NUMBER 917.273062 18 25 17 6 3 4 17 25 22 © m --23 12 KEY PART NO. NO. 1 164094 2 149516 3 163916 4 163917 5 140837 6 133644 7 164757 8 164884 9 163204 10 156439 11 4900J 12 146790 11 KEY PART DESCRIPTION NO, NO.
TRACTOR -- MODEL NUMBER 917.273062 LIFT ASSEMBLY 40 39 42 23 41 23 .......-..G_ 41 43 38 5 4 13 2 25 26 12 22 12 15 20 19 18 16 5O.
TRACTOR -- MODEL NUMBER 917.273062 LIFT ASSEMBLY KEY PART NO. NO, DESCRIPTION 1 121006X Rod Asm., Lever 2 159187 Shaft Asm., Lift Vgt 3 159189 Lever Asm.
TRACTOR - MODEL NUMBER 917.273062 MOWER DECK 59 58 48 6 60 55 45 44 43 48 64 i i 36 36 2 21 22 99 54 10 11 52.
TRACTOR -- MODEL NUMBER 917.273062 MOWER DECK KEY PART NO. NO. 1 156990 2 STD541431 3 72110506 4 7631J 5 138457 6 STD624008 7 130832 8 850857 9 STD551137 10 140296 1! 137380 12 129895 13 137553 14 137.
TRACTOR - MODEL NUMBER 917.273062 TRANSAXLE--MODEL NUMBER 222-3010L 111 (2) 54.
TRACTOR -- MODEL NUMBER 917.273062 TRANSAXLE--MODEL NUMBER 222-3010L KEY PART KEY PART NO. NO, DESCRIPTION NO. NO, DESCRIPTION 1 164591 Assembly, Housing, LH 72 153767 Locknut, Hex 5/16-18 2 164592 Assembly, Housing, RH 73 142904 Bolt, Hex 5/16-18 x 1-1/2 7 153765 Oil Seal .
TRACTOR - MODEL NUMBER 917.273062 TRANSAXLE--MODEL NUMBER 222-3010L .> KEY PART NO. NO. 1 144569 2 122716X 3 122745X 4 122715X 5 122700X 6 122699X 8 122767X 12 122717X 13 122748X 14 122749X 15 1445.
TRACTOR -- MODEL NUMBER 917.273062 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65551 :YLINDER HEAD, VALVE AND BREATHERJ 31 32 30 @ -- 28 I 29 CRANCASE.
TRACTOR -- MODEL NUMBER 917.273062 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65551 IGNITION/ELECTRICALJ _7 AIR INTAKE j BLOWER HOUSING AND BAFFLESJ t2 jl _3 J t0 -'_ .
TRACTOR =- MODEL NUMBER 917.273062 KOHLER ENGiNE-MODEL NUMBER CV20S, TYPE NUMBER 65551 ;TARTING SYSTEM 1 2 5 4 / n @ ENGINE CONTROLS I I @--2 @V' 0 _° 9__ 10J_ t7 _3 '% 6 t2 O 3 14 59.
TRACTOR -- MODEL NUMBER 917.273062 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65551 "RANKSHAFT J FUEL SYSTEM I --1 EXHAUSTJ / 1 13 9 14 6O.
TRACTOR °- MODEL NUMBER 917.273062 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65551 HEAD/VALVE/BREATHER CRANKCASE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRiPTiON 1 24-033-03 Kit, breather cover w/gasket 1 24-032-01 (includes 2,3) 2 2 24-041-23 Gasket, breather 3 24-096-15 Cover, breather 3 24-294,13 4 M-0645020 Screw, hex.
TRACTOR -- MODEL NUM BER 917.273062 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65551 IGNITION/CHARGING BLOWER HOUSING & BAFFLES KEY PART KEY PART NO.
TRACTOR-- MODEL NUM BER 917.273062 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65551 STARTING SYSTEM OIL PAN/LUBRICATION KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 4 5 6 7 8 9 10 11 M"0839070 Screw, hex. flange M8x1.25x70 24-096-05 Cover, pinion M-0839080 Screw, hex.
TRACTOR-- MODEL NUM BER 917.273062 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65551 CRANKSHAFT KEY PART NO. NO. DESCRIPTION FUEL SYSTEM KEY PART NO. NO. DESCRIPTION 1 24-014-72 Crankshaft (Includes 2) 2 52-139-09 Plug, cup EXHAUST KEY PART NO. NO. DESCRIPTION 1 24-041-02 Gasket, exhaust (2) 2 25-072-04 Stud, M8x1.
NOTES.
NOTES 66.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION I "" SIGHTING GUIDE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SIGHT AND HOLD THIS LEVEL WITH SKY LiNE OR TREE. 15 ° MAX. A I Operate your Tractor up and down the face of slopes (not I greater than 15°), never across the face.
Get it fixed, at your home or ours! For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME sM Anyt,r_e, day or o,ght (1-800-469-4663) www.
デバイスCraftsman 917.273062の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 917.273062をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 917.273062の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 917.273062の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 917.273062で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 917.273062を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 917.273062の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 917.273062に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 917.273062デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
