Craftsmanメーカー917.27351の使用説明書/サービス説明書
ページ先へ移動 of 56
Owner's Manual ICRRFTSMRN°I LAWN TRACTOR 21 0 HP, 42" Mower Electric Start 6 Speed Transaxle Model No. 917.273510 This product has a low emission engine which operates IIL-_II differently from previously built engines. Before you start the engine, read and understand this Owner's Manual.
Warranty ................................................. 2 Maintenance ......................................... 17 Safety Rules ........................................... 3 Service and Adjustments ...................... 21 Product Specifications .
IMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death.
DO: • Mow up and down slopes, not across. • Remove obstacles such as rocks, tree limbs, etc. • Watch for holes, ruts, or bumps. Un- even terrain could overturn the machine. Tall grass can hide obstacles. • Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope.
• Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off. • Do not mow in reverse unless abso- lutely necessary. Always look down and behind before and while backing.
PRODUCT SPECIFICATIONS i Gasoline Capacity 3.5 land Type: Unleaded Regular i Oil Type SAE 30 (above 32°F) i (API-SF-SJ): SAE 5W-30 (below 32°F) Oil Capacity: W/Filter: 4.0 Pints W/O Filter:3.75 Pints Spark Plug: Champion QC12YC (Gap: .040") Ground Speed (MPH): Forward: 1st 1.
Steering Wheel Insert (1) Hex Bolt 1/4-28 x 1-1/4 a I I a Steering Wheel Adapter Steering Wheel Q (1) Locknut 1/2-20 Seat (1) Large Flat Washer (1) Locknut 1/4-28 Steering Extension teedng Shaft Boot .
Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
INSTALL SEAT Adjust seat before tightening adjustment knob. 1. Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. 2. Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.
INSTALL MULCHER PLATE (If previously removed) 1. Raise and hold deflector shield in upright position. 2. Place front of mulcher plate over front of mower deck opening and slide into place, as shown. 3. Hook front latch into hole on front of mower deck.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. R N H L I',,I REVERSE NEUTRAL HIGH LOW CHOKE FAST SLOW IGNITION ENGINE OFF.
KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
The cutting height range is approxi- mately 1-1/2 to 4". The heights are mea- sured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.
TOWING CARTS AND OTHER ATTACH- MENTS Tow only the attachments that are recom- mended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.
COLD WEATHER STARTING (50 ° F and below) 7. When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the en- gine to accept small changes in speed and load, until the choke control is fully in.
MA,N. .ANOESO.EOOLE FILL IN DATES AS YOU COMPLETE R EGOLARSERVlOE I SERV'CEOAT S C :i:: kk B_a:; iOP:ur ra;i° n _ l Check Operator Presence and T Interlock Systems R Check for Loose Fasteners _ .
TRACTOR Always observe safety rules when per- forming any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual).
BATTERY Your tractor has a battery charging system which is sufficient for normal use. How- ever, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open.
8. Use gauge on oil fill cap/dipstick for checking level. For accurate reading, tighten dipstick cap securely onto the tube before removing dipstick. Keep oil at "FULL' line on dipstick. Tighten cap onto the tube securely when finished. AIR FILTER Your engine will not run properly using a dirty air filter.
CLEANING • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with auto- motive type wax.
6. Connect anti-sway bar to chassis bracket and secure with retainer spring. 7. Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring. 8. Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.
2. Work belt off both mandrel pulleys and idler pulleys. 3. Pull belt away from mower. BELT INSTALLATION - 1. Work belt around both mandrel pulleys and idler pulleys 2. Make sure belt is in all pulley grooves and inside all belt guides. 3. Install mower (See "To Install Mower" in this section of this manual).
Engine Pulle Clutching Stationary Keeper Transaxle Pulley TRANSAXLE GEAR SHIFT LEVER NEU- TRAL ADJUSTMENT The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows: 1.
TO START ENGINE WITH A WEAK BAT- TE RY _ILWARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries. If your battery is too weak to start the engine, it should be recharged.
TO REMOVE HOOD AND GRILL AS- SEMBLY 1. Raise hood. 2. Unsnap headlight wire connector. 3. Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. 4. When replacing hood, be sure to re- connect the headlight wire connector.
Immediately prepare your tractor for stor- age at the end of the season or if the trac- tor will not be used for 30 days or more. _,CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Will not start Hard to start i Engine will not turn over i Engine clicks but will not start CAUSE CORRECTION 1. Out of fuel. 2. Engine not "CHOKED" properly.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center CAUSE 1. Cutting too much grass/too fast. , 3. PROBLEM Loss of power Excessive vibration Engine continues to run when operator leaves seat with attach- ment clutch engaged .
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Mower blades will not rotate Poor grass discharge Headlight(s) not working (if so equipped) Battery will not charge Engine "backfires" when turning engine "OFF" CAUSE CORRECTION 1.
TRACTOR - - MODEL NUMBER 917.273510 SCHEMATIC .Ik 0E0 o111 0LAOK BATTERY RED I AMMETER (OPTIONAL) WHETE )G A1 IGNITION SWITCH IGNITION SWITCH FUSE I I '© : _2) I L J CLUTCH / BRAKE (PEDAL UP) BL.
TRACTOR - - MODEL NUMBER 917.273510 ELECTRICAL / I I I I 42 i I 41 22 I I ( I I I I I I I i I I 26 /i I // I I/ I I/ I I J / / / / I 33 "_ I/// / I I I I I I I 29 I I I I I 16 i / 7 I I I / I / .
TRACTOR - - MODEL NUMBER 917.273510 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 144927 Battery 2 74760412 Bolt Hex Hd 1/4-20 unc x 3/4 8 7603J Case Battery 10 145211 Bolt, Btr Front 1/4-20 x 7-1/2 11 15.
TRACTOR - - MODEL NUMBER 917.273510 CHASSIS AND ENCLOSURES 212 -- 31 28 39 58 222 208 209 60 208 j64 219 __20 23 219 74 209 14 37 _145 j37 208 206 209 chassis-Laser -It.
TRACTOR - - MODEL NUMBER 917.273510 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 174619 2 176554 5 155272 9 168337X013 10 STD533710 11 174996 13 172105X010 14 17490608 17 185682X558 18 184921.
TRACTOR - - MODEL NUMBER 917.273510 GROUND DRIVE 57 18 25 212 70 116 150 • 48 ,151 37 i3 26 27 drive-fender.stir 26 36.
TRACTOR - - MODEL NUMBER 917.273510 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 ........ Transaxle (See Breakdown) 62 8883R Peerless 206-545C 63 175410 2 146682 Spring, Return, Brake .
TRACTOR - - MODEL NUMBER 917.273510 STEERING 88 J J I 17 47 67 67 67 68 steering_pl,lt 55 / 30 43 8 38.
TRACTOR - - MODEL NUMBER 917.273510 STEERING KEY PART NO. NO. DESCRIPTION 1 139768 Steering Wheel 2 175131 Axle Assembly 3 169840 Spindle Assembly, L.H. 4 169839 Spindle Assembly, R.H. 5 6266H Bearing, Race, Thrust, Hardened 6 121748X Washer 25/32 x 1-5/8 x 16 Ga.
TRACTOR - - MODEL NUMBER 917.273510 ENGINE 2 1_ 14 38 32 31 39 33 29 OPTIONAL EQUIPMENT Spark Arrester 23 13 I i engine-bs iatek-twin 29 KEY PART NO. NO. 1 170546 2 17720408 3 4 149723 5 159955 6 160589 8 171877 10 162797 13 165391 14 148456 17 17060624 23 169837 25 145996 26 73920600 29 137180 DESCRIPTION KEY PART NO.
TRACTOR - - MODEL NUMBER 917.273510 LIFT ASSEMBLY 7 5 13 6 3 2 6 5 19 13 32 32 13 19 20 15 20 lift- rh, 1 piece 3 KEY PART NO. NO. 1 159460 2 159471 3 105767X 4 12000002 5 19211621 6 120183X 7 125631X.
TRACTOR - - MODEL NUMBER 917.273510 SEAT ASSEMBLY I I I I I .....-- 16 11 seatJt.knob 13 KEY PART NO. NO. 1 140122 2 140551 3 71110616 4 19131610 5 145006 6 STD541437 7 124181X 8 17000616 9 19131614 10 182493 11 166369 12 121246X 12 DESCRIPTION Seat Bracket Pnt Pivot Fender Belt Fin Hex 3/8-16 unex 1 Washer 13/32 x 3/4 x 10 Ga.
TRACTOR - - MODEL NUMBER 917.273510 DECALS 7 5 20 7 13 " "'"; i 2 • • i Id=.... =l 15 KEY PART NO. NO. 1 156439 2 189622 3 184728 4 184729 5 184730 6 133644 7 189647 8 188999 9 184899 11 156368 DESCRIPTION Decal, Fender Danger Sears Decal, Engine Decal, Hood, R.
TRACTOR - - MODEL NUMBER 917.273510 MOWER DECK z i- i147 142 106_ 102 103 105 103 _/_'y J / / 1011_ 104 106 2 16 21 23 24 27 5 6 42 D man-t-path stlt 3 44.
TRACTOR - - MODEL NUMBER 917.273510 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 165892 Mower Deck Assembly, 42" 59 141043 2 STD533107 Bolt 67 149846 3 138017 Bracket As.
TRACTOR - - MODEL NUMBER 917.273510 PEERLESS TRANSAXLE--MODEL NUMBER 206-545C 35A 8 157 47 _,,,,31A 15 18 4 / 34 79 46.
TRACTOR - - MODEL NUMBER 917.273510 PEERLESS TRANSAXLE--MODEL NUMBER 206-545C KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 772147 Transaxle Cover 39 786026 2 780086A Needle Bearing 5/8" 40 792.
TRACTOR - - MODEL NUMBER 917.273510 BRIGGS & STRATTON ENGINE-MODEL NUMBER 407577,TYPE NUMBER 0283-E1 26 523 842c 525 287 1026 } 447A 524@ _ 252 4J 691 1019 LABEL KIT 24[_ 1017_ 304 1053 OWNER&apos.
TRACTOR - - MODEL NUMBER 917.273510 BRIGGS & STRATTON ENGINE-MODEL NUMBER 407577,TYPE NUMBER 0283-E1 35 36 _ 1022 1029 1100 798_ 7 _ 1022 35 11oo 1023_ 240_ 121 CARBURETOR OVERHAUL KIT 51 276 @ 63.
TRACTOR - - MODEL NUMBER 917.273510 BRIGGS & STRATTON ENGINE-MODEL NUMBER 407577,TYPE NUMBER 0283-E1 40 058 ENGINE GASKET SET 20 @ oo0 024 @ 1022 _ 01 042 01A @ 691 @ 01B (_ 002 7 71 3_ 9 5O.
TRACTOR - - MODEL NUMBER 917.273510 BRIGGS & STRATTON ENGINE-MODEL NUMBER 407577,TYPE NUMBER 0283-E1 KEY PART KEY PART NO, NO. DESCRIPTION NO. NO. DESCRIPTION 1 699751 Cylinder Assembly 180 699809.
TRACTOR - - MODEL NUMBER 917.273510 BRIGGS & STRATTON ENGINE-MODEL NUMBER 407577,TYPE NUMBER 0283-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 467 69I 008 Knob-Air Cleaner 877 3934.
53.
54.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION 1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure.
Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.
デバイスCraftsman 917.27351の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 917.27351をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 917.27351の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 917.27351の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 917.27351で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 917.27351を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 917.27351の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 917.27351に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 917.27351デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
