Craftsmanメーカー917.27582の使用説明書/サービス説明書
ページ先へ移動 of 56
Owner's Manual JCRRFTSMRN°J LAWN TRACTOR 18.5 HP, 42" Mower Electric Start Automatic Transmission Model No. 917.275820 [_ his product has a low emission engine which operates differently from previously built engines.
Warranty ................................................ 2 Safety Rules .......................................... 3 Product Specifications ........................... 6 AssemblyPre-Operation ........................ 8 Operation .....................
IMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death.
II. SLOPE OPERATION Slopes are a major factor related to loss of control and tip-over accidents,which can result in severe injury or death. Opera- tion on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
• Remove gas-powered equipmentfrom the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipmentwith a portable container, rather than from a gasoline dispenser nozzle. • Keepthe nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete.
PRODUCT SPECIFICATIONS Gasoline 3.5 Gallons Capacity Unleaded and Type: Regular Oil Type SAE 30 (above 32°F) (API-SG-SL): SAE 5W-30 (Below 32°F) Oil Capacity: W/Filter: 3.5 Pints W/O Filter: 3.0 Pints Spark Plug: Champion RC12YC (GAP: .030") Ground Speed Forward: 5.
Steering Wheel Insert Steering Boot (1) Hex Bolt R 5/16-18 x 4 Steering Wheel (1) Large Flat Washer Steering Wheel Adapter (1) 5/16 Lock Washer Seat (1) Washer _ 17/32 x 1-3/16 x 12 Gauge _7{_9 (1) Kn.
Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
6. Lower seat into operating position and sit in seat. 7. Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down. 8. Get off seat without moving its ad- justed position. 9. Raise seat and tighten adjustment knob securely.
CHECKTIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Cor- rect tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. R N H REVERSE NEUTRAL HIGH LOW 6 6 ENGINE OFF REVERSE ENGINE ON ENGINE START OP.
KNOWYOUR TRACTOR READTHIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles.
TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.
TO OPERATE ON HILLS _ILWARNING: Do not drive up or down hills with slopes greater than 15 ° and do not drive across any slope. Use the slope guide at the back of this manual. • Choose the slowest speed before start- ing up or down hills. • Avoid stopping or changing speed on hills.
TO START ENGINE When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. 1. Be sure freewheel control is in the transmission engaged position. 2. Sit on seat in operating position, depress clutch/brake pedal and set parking brake.
MOWING TIPS • Mower should be properly leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has already been cut.
FILL IN DATES /_/_X'x_'_/_ _ " AS YOU COMPLETE /__/_ _4 _/_/O.Oq. _" REGULAR SERVICE /_r/_'_VSERVICE DATES Check Brake Operation _ Check Tire Pressure Check Operator Presence .
TRACTOR Always observe safety rules when per- forming any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.
NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not. • Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position.
Oil Drain Valve Closed and Locked Position Yellow Ca Drain Tube 3. Unlock drain valve by pushing inward slightly and turning counterclockwise. 4. To open, pull out on the drain valve. 5. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.
MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could cre- ate a fire hazard and/or damage. SPARK PLUG(S) Replace spark plug(s) at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place motion control lever in neutral (N) position. 3. Place attachment clutch in "DISENGAGED" position.
7. Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring. 8. Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring. 9. Install belt onto engine pulley. TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway.
BELT INSTALLATION - 1. Work belt around both mandrel pulleys and idler pulleys 2. Make sure belt is in all pulley grooves and inside all belt guides. 3.
Engine Pulley ____ Clutching --I Stationary _[----_,-i _ I II Center Span II__--J--.[ Keeper.-------_ _ Transmission II__P_L Input Pulley/_ TRANSAXLE MOTION CONTROL LE- VER NEUTRAL ADJUSTMENT The motion control lever has been preset at the factory and adjustment should not be necessary.
If "jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles. TO ATTACH JUMPER CABLES - 1.
ENGINE Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.
Immediately prepare your tractor for stor- age at the end of the season or if the trac- tor will not be used for 30 days or more. _CAUTION: Neverstore the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Will not start Hard to start Engine will not turn over Engine clicks but will not start Loss of power 1. Out of fuel. 2. Engine not "CHOKED" properly.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CORRECTION Loss of power (cont.) Excessive vibration Engine dies when tractor is shifted into reverse Engine continues to run when operator leaves seat with attachment clutch engaged Poor cut - uneven CAUSE 6.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Mower blades will not rotate Poor grass discharge Headlight(s) not working (if so equipped) Battery willnot charge Loss of drive Engine "backfires' when turning engine "OFF" 1.
SCHEMATIC TRACTOR - - MODEL NUMBER 917.275820 (OPT]ONAN IGNITION SWITCH POSITION CIRCUIT "MAKE" OFF M+G+A1 RUN/OVERRIDE B+A1 RUN B+A1 L+A2 START B+S+A1 WHITE CLUTCH / BRAK_E B_ACK i_ _ BI_CK REVERSE SWITCH r = I BLACK SOLENOID STARTER SHORTING CONNECTOR b b BLACK GRAY b .
ELECTRICAL 90 TRACTOR - - MODEL NUMBER 917.275820 41 25 ! .............. I I i I I I _6 _ 16 ' I I ! i _ i ! i 1 1 ! // ! / ! 29 I i 34.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.275820 KEY PART NO. NO. DESCRIPTION 1 163465 Battery 2 74760412 Bolt, Hex 1/4-20 x 3/4 8 186491 Box, Battery 16 176138 Switch Interlock 21 183759 Harness, Light.
TRACTOR - - MODEL NUMBER 917.275820 CHASSIS AND ENCLOSURES 259 260 258 273 _275 278 11_ 208 20T 39 58 278 209 208 / 2_ 2O6 209 209 6O 74 208 chassis-Laser-It.
TRACTOR - - MODEL NUMBER 917,275820 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 174619 Chassis 2 176554 Drawbar 5 155272 Bumper Hood/Dash 9 193511X013 Dash 10 STD533710 Bolt, Carriage 3/8-16.
TRACTOR - - MODEL NUMBER 917.275820 GROUND DRIVE 247 32 /3o 95 I 21 / 82 165 156 166 _-8 35 _39 4T'_ 62 12011 _ 36 52 30 29 252 19 25 36 35 / i 55 116 74 75 78 /76 drive-hydro,stlt 53 38.
TRACTOR - - MODEL NUMBER 917.275820 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 Transaxle Peerless LTH2000 (See 69 142432 Breakdown) 70 134683 8 192502 Rod Shift Fender Adjust 74 137057 10 STD561210 Pin Cotter 1/8 x 1 CAD 75 121749X 14 10040400 Washer Lock Hvy Helical 76 STD581075 15 74490544 Bolt Hex FLGHD 5116-18 Gr.
TRACTOR - - MODEL NUMBER 917.275820 STEERING ASSEMBLY _/ _+_=TJ--- 34 /j::_39 ........... / -L 4 88 L 29 / 15 1515_ ............. steering pl.lt 57 82 4O / 10 68 13 65 67 67 8 6 43 / / 95 / ( / f 40.
TRACTOR - - MODEL NUMBER 917.275820 STEERING ASSEMBLY KEY PART NO. NO. 1 186093X428 2 184706 3 169840 4 169839 5 6266H 6 121748X 8 12000029 10 175121 11 STD551137 13 136518 15 145212 17 190753 26 1268.
ENGINE 2 1 31 39 TRACTOR - - MODEL NUMBER 917,275820 i 32 78_ 33 23 81 72 62 14 29 OPTIONAL EQUIPMENT Spark Arrester engine-bs.lcyl 30 KEY PART NO. NO.
TRACTOR - - MODEL NUMBER 917.275820 SEAT ASSEMBLY 17 12 seat It.knob 1 5 10 KEY PART NO. NO. 1 188719 2 140551 3 71110616 4 19131610 5 145006 6 STD541437 7 124181X 8 17000616 9 19131614 10 182493 11 166369 12 174648 DESCRIPTION Seat Bracket Pnt Pivot Seat Bolt Fin Hex 3/8-16 unc x 1 Washer 13/32 x 3/4 x 10 Ga.
DECALS TRACTOR - - MODEL NUMBER 917.275820 16 7 3 2 2 1 11 14 5 15-- 22 19 14 KEY PART NO. NO. 1 156439 2 186367 3 186366 5 189020 6 133644 7 193565 8 179128 9 186572 11 193307 14 189088 15 160396 20.
TRACTOR - - MODEL NUMBER 917.275820 LIFT ASSEMBLY 7 13 19 ? 13 13 31 -.. 32" 1718 20 16 15 lift-rh=l piece 3 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 159460 Lift Lever Inner Wire Asm. 15 173288 2 159471 Shaft Asm. Lift 16 73350800 3 105767X Pin Groove 17 175689 4 12000002 E Ring 18 73800800 5 19211621 Washer 21132 x 1 x21 Ga.
TRACTOR - - MODEL NUMBER 917,275820 MOWER DECK 3 52 55 ' 142 il 47 119 113 111 _2 5 6 f 19 21 42 D man-t-path stlt 3 21 28 29 12 23 24 117 _116 25 26 27 46.
TRACTOR - - MODEL NUMBER 917.275820 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 165892 Mower Housing 56 165723 2 STD533107 Bolt 59 141043 3 138017 Bracket Asm,Sway Bar, Fron.
TRACTOR - - MODEL NUMBER 917.275820 PEERLESS TRANSAXLE - - MODEL NUMBER LTH2000 1 _, 150 115 87 "_ _ _ 15 106 .(_)-_},_ v _ __.,m 31 29 _- - _ 5 _ (_(_ 106 _ _ 56 6 31 157 _'_1113 :_ (_ _-_ _ _ 32 49 ,_ 67 _= _ _u_ 114 9 87 • 3 _ 208 ' 185 200 25 / / / 22 // / .
TRACTOR - - MODEL NUMBER 917.275820 PEERLESS TRANSAXLE - - MODEL NUMBER LTH2000 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 772151 Cover L.H. 70 786196 Spacer .625.765 3 770135 Case 79 792201 Spring 5 776355 Counter Shaft 85 792154 Oil Fill Plug 6 778263 Spur Gear 11T 87 788088A Oil Seal 3/4" 9 786197 Neutral Sleeve (.
TRACTOR - - MODEL NUMBER 917.275820 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0296-E1 30 i 307_ 3@ 358 ENGINE GASKET SET 12 1022 20@ 6170 868_) 943 0 51 _} 691(_ 0 524 _ 842 O 1266.
TRACTOR - - MODEL NUMBER 917.275820 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0296-E1 914 238 1022 103 z 1022 6170 93'_ 95t_ 1266A 334 366 ,<_ 121 CARBURETOR OVERHAUL KIT 1.
TRACTOR - - MODEL NUMBER 917.275820 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0296-E1 305A 643 1265 1267 1040 968 305' _ 729 697 _" 1070 1005 _ 1044_ 1051& 801 _ 544_.
TRACTOR - - MODEL NUMBER 917.275820 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0296-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO.
TRACTOR - - MODEL NUMBER 917.275820 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0296-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION (_ O1 ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. _ ARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
iiiiiiiiiiiiiiiiiii¸¸ iiiiiiiiii '_ iiiiiiiiii iiiiiiiiii iiiiiiiiii iiiiiiiiii iiiiiiiiii iiiiiiiiii iiiiiiiiii iiiiiiiiii iiiiiiiiii iiiiiiiiii iiiiiiiiii iiiiiiiiii iiiiiiiiii iiiiiiiiii iii.
デバイスCraftsman 917.27582の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 917.27582をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 917.27582の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 917.27582の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 917.27582で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 917.27582を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 917.27582の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 917.27582に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 917.27582デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
