CraftsmanメーカーTILLER 917.29332の使用説明書/サービス説明書
ページ先へ移動 of 36
Owner's Manual CRAFTSMAN 65 HP 19 INCH TINE WIDTH REAR TINE WITH DUAL ROTATING TINES TILLER Model No. 917.293320 • Safety • Assembly • Operation • Maintenance • Espa_ol • Repair Parts CAUTION: Read and follow all Safety Rules and Instructions before operating this equipment Sears, Roebuck and Co.
Warranty ............................. ; ................... 2 Safety Rules ..................... :. .................... 2 Product Specifications .......................... 4 Assembly ........................... _ .................... 5 Operation ...
OPERATION • Do not put hands or feet near'or under rotating parts. • Exercise extreme caution when operat- ing on or crossing gravel drives, walks, or roads.
PRODUCT SPECIFICATIONS 1 ! -IORSEPOWER: 6.5.HP )ISPLACEMENT: 12.48 CU. IN. (266CO) GASOLINE CAPACITY: 3 Quads Unleaded Regular OIL (API-SF/SG/SH): SAE 30 (Above 40°F) CAPACITY: 19 oz.) SAE5W-30/10W-30 (Below 40°F) SPARK PLUG : Champion RJ19LM (GAP: .
Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
UNPACKING CARTON _,CAUTION: Be careful of.exposed sta- ples when handling or disposing of carton- ing material. IMPORTANT:When unpacl_ing and assembling tiller, be careful not to stretch or kink cables. • While holding handle assembly, cut cable ties securing handle assembly to top frame.
INSERT CABLE CLIP • Insert plastic cable clip into hole on the back of handle column. Push cables into clip. Handle Column Cables Attach this end to shift lever _"_Attach this EndTo shi" _.
These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning. CAUTION ENGIN_ ENGINE TILLINO TILLING FOI_WARD NEUTRAL REVERSE ORWA_I_tG' ON OFF KNOW YOUR TILLER READ THIS OWNER'S MANUALAND SAFETY RULES BEFORE OPERATING YOUR TILLER.
The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilhng. We recommend a wide vision safety maskover spectacles or standard safety glasses.
TURNING • Release the drive control bar. • Move throttle control to =SLOW" posi- tion. • Place shift lever indicator in "F _ (forward) position. Tines will not turn. : Lift handle to raise tines out of ground. Swing the handle in the opposite direc- tion you wish to turn, bein'g careful to keep feet and legs away from tines.
WARNING: Experience indicates that alco- h01 blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can dam- age the fuel system of an engine while in storage.
• Do not lean on handle..This takes weight off the wheels andreduces rac- tion. To get through a ,rea!ly tough sec- tion of sod or hard ground, apply upward pressure on handle or lower the depth stake. CULTIVATING Cultivating is destroying the weeds ' between rows to prevent them from rob- bing nourishment and moisture from the plants.
WW SCHEDULE F I,,,N o, °s /. 7'2Z ya ,, ERV,OE Check Engine Oil Level l/ k/ Change Engine Oil t_,2 Oil Pivot Points Inspect Spark Arrester / Muffler t4/ Inspect Air Screen IV / Clean or Replace .
Disconnect spark plug wire beforeper- forming any maintenance (except carbure- tor adjustment) to prevent accidental start- ing of engine. Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Remove fuel from tank before tipping unit for main- tenance.
Cover_ COOLING SYSTEM Your engine is air cooled. For proper engine performance and long life keep your engine clean. • Clean air screen frequently using a stiff- bristled brush. • Keep cylinder fins, levers, and linkage free of dirt and chaff. Muffler MUFFLER Do not operate tiller without muffler.
TIRE CARE _.CAUTION: When mouhting tires, un- less beads are seated, overinflation can cause an explosion. • Maintain 20 pounds of air pressure. If tire pressures are not equal, tiller will pull to one side. • Keep tires free of gasoline or oil which can damage rubber.
Engine_ t , ip Screw }dve Control Cable Idler Pulley Transmission Pulley TINE REPLACEMENT • A, CAUTION: Tines are sharp. Wear gloves or other protection when handling tines.
ENGINE Maintenance, repair, or repracement of the emission control devices and systems, which are being done at thQ customers expense, may be performed by any non- road engine repair establishment or indi- vidual. Warranty repairs must be per- formed by an authorized engine manufac- turer's service outlet.
Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more. A_,CAUTION: Never store the tiller with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.
PROBLEM Will not start Hard to start Loss of power CAUSE I 1. Out of fuel. 2. Engine not "CHOKED" properly. 3, Engine flooded. 4. Dirty air cleaner. 5. Water in fuel. 6. Clogged fuel tank. 7. Loose spark plug wire. 8. Bad spark plug or improper gap.
PROBLEM Engine overheats Excessive bounce/ difficult handling Soil balls up or clumps Engine runsbut tiller won't move Engine runsbut labors when tilling Tines skip over ground CAUSE 1. Low oil level/dirty oil. 2. Dirty engine air screen. 3. Dirty engine.
TILLER - - MODEL NUMBER 917.293320 HANDLES 3 2 1 29 7 / 30 11 KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 16 17 PART NO. DESCRIPTION 164743 Throttle,Control 141406 Gdp, Handle 110673X Grommet, Hand.
TILLER - - MODEL NUMBER 917.293320 MAINFRAME, LEFT SIDE, 9 7 31 24 KEY PART NO. NO. DESCRIPTION 1 STD541431 Nut, Keps 5/16-18 24 2 STD551137 "Washer, Lock 3/8 25 3 STD541037 *Nut, Hex 3/8-16 26 4 165710 Shiek:HP, ner 27 5 164329 Pin Shift Lever 28 6 162756X505 Lever, Shift 29 7 STD532505 "Bolt, Carriage 1/4-20 x 1/2 Gr.
TILLER - - MODEL NUMBER 917.293320 MAINFRAME, RIGHT SIDE 13 12 y 11 15 lO 4 KEY PART NO. NO. DESCRIPTION 1 166532 Bumper 2 73970500 Locknut, Hex, Range 5/16-18 3 STD551031 *Washer 11/32 x 11116 x 16 Ga. 4 74760512 Bolt, Hex 5/16-18x3/4 5 102332X Bracl_et, Reinforcement 6 74760532 Bolt'Hex 5/16-18x2 7 102173X CounterWeight, R.
TILLER - - MODEL NUMBER 917.293320 TRANSMISSION d j;1 i 5 1 Z 30 ._° ./ 58 KEY PART NO. NO. DESCRIPTION 161509 161510 3 161963 4 5020J 5 1370H 6 161520 7 161518 8 4895H 9 154467 10 7392M 11 100371K 12 106160X 13 142145 14 8353,1 15 12000039 16 161516 18 4358,.
TINE SHIELD TIL_ER - - MODEL NUMBER 917.293320 17 5 5 7 13 14 24 24 KEY PART NO. NO. 1 98000129 2 161415X558 3 8393J 4 1200O036 5 STD533107 6 8394J 7 8392J 8 109230X 9 163496X558 10 104085X558 11 STD541031 12 STD551131 13 72110510 14 124343X 15 161414X558 16 73510400 KEY PART DESCRIPTION NO.
TILLER -- MODEL NUMBER 917.293320 TINE ASSEMBLY 1 1 KEY PART NO. NO. DESCRIPTION 1 163499 "nne,Spade 2 132673 Pin, Shear 3 163500 _ne, Cleaning 4 163552 "Clip,Haiq_in 5 163926 Assembly, Hub and Plate KEY PART NO.
,DECALS TILLER - - MODEL NUMBER 917.293320 4 10 3 11 8 KEY PART NO. NO. 1 164709 2 145023 3 166186 4 166187 5 137538 6 120431X ,t 7 166202 8 166188 9 120075X 10 165836 11 162215 12 166138 13 165837 - o 165984 DESCRIPTION Decal, Logo Decal, Logo Decal, Logo Decal, Description Decal, Caution, Drive Control Decal.
TILLER - - MODEL NUMBER 917.293320 ENGINE, BRIGGS & STRAI"FON -,- MODEL NUMBER 121432, TYPE NO. 0124-E1 3O5 e,. 478 12 I 1019 LABEL KIT I 11058 OWNER'S MANUAL I 51 341 868 40L_[ lk REQUI.
TILLER -- MODEL NUMBER 917.293320 ENGINE, BRIGGS & STRATTON - - MODEL NUMBER 121432, TYPE NO. 0124-E1 24 I 634A _ 634 _2_ 110(_ 110_ 5O.
TILLER -- MODEL NUMBER 917.293320 ENGINE, BRIGGS & STRAI"rO N - - MODEL NUMBER 121432, TYPE NO. 0124-E1 23 1005 304 305A_ lp 623_ 456_ 009 /'//] I 60_ 373A_ 55A 51.
TILLER -- MODEL NUMBER 917.293320 I , ENGINE, BRIGGS & STRAI"FON - - MODEL NUMBER 121432, TYPE NO. 0124-E1 2271 562 _ i 2221 les_p e21 '_,_ 2e5,_ 281 [,_J_,_ 663 211 _ 3_ '_ I 958 .
TILLER - _- MODEL NUMBER 917.293320 ENGINE, BRIGGS & STRATTON - - MODEL NUMBER 121432, TYPE NO. 0124-E1 358 GASKET SET ,,J,.o 977 CARBURETOR GASI_ET'SET 121 CARBURETOR KIT ,70 °"° 110_.
TILLER - - MODEL NUMBER 917.293320 ENGINE, BRIGGS & STRATTON - - MODEL NUMBER 121432, TYPE NO, 0124-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO.
TILLER -- MODEL NUMBER 917.293320 ENGINE, BRIGGS & STRA'I-I'ON - - MODEL NUMBER 121432, TYPE NO, 0124-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO.
For the repair or replacement parts you need delivered directly to your home Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio - 1-800-659-708.
デバイスCraftsman TILLER 917.29332の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman TILLER 917.29332をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman TILLER 917.29332の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman TILLER 917.29332の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman TILLER 917.29332で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman TILLER 917.29332を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman TILLER 917.29332の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman TILLER 917.29332に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman TILLER 917.29332デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
