CrestronメーカーMultimedia Presentation System 300 MPS-300の使用説明書/サービス説明書
ページ先へ移動 of 96
Crestron MPS-300 Multimedia Presentation System 300 Operations Guide.
This document was prepared an d written by the Tech nical Documentation dep artment at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Important Safety Instructions • Read these instructions. • Keep these instr uctions.
Crestron MPS-300 Multimedia Presentation System 300 Operations Guide – DOC. 6529B Contents • i Contents Multimedia Presentation System 300: MPS-300 1 Introduction ....................................................................................
.
Crestron MPS-300 Multimedia Presentation System 300 Multimedia Presentation System 300: MPS-300 Multimedia Presentation System 300: MPS-300 Introduction Introduction Features and Functions • System .
Multimedia Presentation System 300 Crestron MPS-300 Composite , S-video, com ponent and R GBHV signals ca n be route d to the appropriate i nputs on t he display devi ce, with co ntrol of the display pr ovided via Ethernet, RS-2 32 or IR.
Crestron MPS-300 Multimedia Presentation System 300 Professional Audio Features Five stereo aud io inputs o n the rear panel accept balance d or unbalance d line-level signals from computers and othe r program audio sources. Addi tional audio s ources can be brought in th rough the three QM inputs.
Multimedia Presentation System 300 Crestron MPS-300 presentation room with a single projector, sc reen, and keypad cont roller, to a fully custom touchpanel based system with multiple controlled sources and display devices, can be programmed easily using Crestron SystemBuilder™ software.
Crestron MPS-300 Multimedia Presentation System 300 For more in formation o n this and other QM applications, refer to the latest revision of the Crestron MediaManager Applicati ons Gui de (Doc. 6244), whic h is available from the Crestron website ( http://www.
Multimedia Presentation System 300 Crestron MPS-300 Audio Block Diagram of the MPS-300 8x4 Matrix Switch AUDIO INPUTS QM OUT5 (Touc hpan el) Stereo Audio 1 2 3 4 5 QM OUT 6 6 A/D A/D A/D A/D A/D 7 QM .
Crestron MPS-300 Multimedia Presentation System 300 MPS-300 Specifications (Continued) SPECIFICATION DETAILS Video/RGB Switcher Signal Types Video/HDTV Formats RGB Formats Maximum Resolution Blanking .
Multimedia Presentation System 300 Crestron MPS-300 MPS-300 Specifications (Continued) SPECIFICATION DETAILS Audio (continued) Limiter Curve Limiter Threshold Level Limiter Attack Time Limiter Release.
Crestron MPS-300 Multimedia Presentation System 300 MPS-300 Specifications (Continued) SPECIFICATION DETAILS LCD Display Green LCD alphanumeric, adj ustabl e backlight.
Multimedia Presentation System 300 Crestron MPS-300 MPS-300 Specifications (Continued) SPECIFICATION DETAILS Available Accessories: APAD C2N-DB12 C2N-FTB C2N-MNETGW CLS-C6(M) CLW-DIM1RF and CLW-SW1RF .
Crestron MPS-300 Multimedia Presentation System 300 MPS-300 Overall Dimensions 17.03 in (43.24 cm) 3.47 in (8.81 cm) 11.85 i n (30.08 cm) 12.58 i n (31.
Multimedia Presentation System 300 Crestron MPS-300 MPS-300 Buttons and Ports 1 2 3 4 5 6 8 9 10 11 12 14 16 17 19 20 30 18 21 23 24 22 27 25 29 31 32 34 15 28 26 7 13 33 12 • Multimedia Presentation System 30 0: MPS-300 Operations Guide – DOC.
Crestron MPS-300 Multimedia Presentation System 300 Connectors, Controls & Indicators # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 1 NET LED (1) yellow LED, indicates Cresnet bus activit y. 2 MSG LED (1) yellow LED, illuminates when a message is present in the message log.
Multimedia Presentation System 300 Crestron MPS-300 Connectors, Controls & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 8 MC/LN 1 – 2 (2) 5-pin 3.
Crestron MPS-300 Multimedia Presentation System 300 Connectors, Controls & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 12 REC OUT (1) 5-pin 3.
Multimedia Presentation System 300 Crestron MPS-300 Connectors, Controls & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 18 IR IN (1) 3-pin 3.
Crestron MPS-300 Multimedia Presentation System 300 Connectors, Controls & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 25 TOUCH PANEL OUT Contains one CH port and one QM port.
Multimedia Presentation System 300 Crestron MPS-300 Connectors, Controls & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 27 COM A & B (2) DB9 male, bidirectional RS-232 ports; Up to 115.2k baud, hard ware and software handshaking support for communication with serial devices.
Crestron MPS-300 Multimedia Presentation System 300 Connectors, Controls & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 30 OUTPUT 1-4 Contains composite, S-video (Y/C), component (Y, P b , P r ) and RGBHV outputs on six BNC connectors and one DB15HD connector.
Multimedia Presentation System 300 Crestron MPS-300 Connectors, Controls & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 32 NET (4) 4-pin 3.
Crestron MPS-300 Multimedia Presentation System 300 Industry Compliance This product is Listed to a pplicable UL Standar ds and requi rements by U nderwriters Laboratories Inc.
Multimedia Presentation System 300 Crestron MPS-300 Setup Network Wiring When wiring the network, consider th e following: • Use Crestron Certified Wire. • Provide sufficient power to the system. CAUTION: Insufficie nt power can lead to unpre dictable results or damage to the equipment.
Crestron MPS-300 Multimedia Presentation System 300 QuickMedia Wiring The Crestron QuickMedia cable (s old under the name “C resCAT-QM”) cont ains one CAT5E cable and one Cresnet cable in Si amese jackets. Installation of a ny QM device is as sim ple as installing CresCAT-QM wi res from t he output o f one device to the input of another.
Multimedia Presentation System 300 Crestron MPS-300 QM Network Topology TPS-12G/15G-QM-L MPS-300 QM QM QM QM QM Originati on P oints Endpoi nts QM Midpoi nts MPS-300 MPS-300 QM-MD7x2 MPS-300 TPS-12G/15G-QM-L Installation Ventilation The MPS-300 should be used in a well-vent ilated area.
Crestron MPS-300 Multimedia Presentation System 300 Ear Attachment for Rack Mounting 4. Repeat procedure (steps 1 through 3) to attach the remaining ear to the opposite side. NOTE: The sync input impedance an d DDC featu re should be set prior to placi ng the MPS ent rack.
Multimedia Presentation System 300 Crestron MPS-300 Hardware Connections for the MPS-300, Rear TO SPEAKERS: 8-OHM STEREO (MPS-300) 70 VOLT MONO (MPS-300-70V) 100 VOLT MONO (MPS-300-100V) AUDIO INPUTS:.
Crestron MPS-300 Multimedia Presentation System 300 NOTE: When r unning the out-of-the-b ox program and connecting a pro jector screen, the “up” control lines should be connected to relay 1 and the “dow n” control lines should be connected to relay 2.
Multimedia Presentation System 300 Crestron MPS-300 Configure the RGB Input Ports Each of the RGB input port s feature a set of six DIP switches located ins ide the MPS-300. The se switches are used to set the sync input im pedance of eac h port and simulate the presence of a m onitor (DDC ) for each R GB input.
Crestron MPS-300 Multimedia Presentation System 300 DIP Switch Location DIP SWITCHES LOCA TED UNDER ACCES S PANEL Set the DIP Switches 1. Referring to the followi ng table, set the DIP switches of each RGB input port to the required sync input impedance and DDC functionality.
Multimedia Presentation System 300 Crestron MPS-300 Label the Buttons Use Crestr on Engraver software to p rint custom labels for the MPS-30 0’s front pa nel buttons and L EDS.
Crestron MPS-300 Multimedia Presentation System 300 Programming Software Have a questi on or commen t about Crestr on software? Answers to f requently asked quest ions (FAQs) can be viewed in the Onl ine Help section of the Crestro n website.
Multimedia Presentation System 300 Crestron MPS-300 Configuration Manager Configuration M anager is the view where programm ers “build” a Crestro n control system by selecting hard ware from t he Device Library .
Crestron MPS-300 Multimedia Presentation System 300 To save settings for later use, use Crestron Toolbox’ File Manager utility to retrieve the *.xml (where * can be “ootbf” fo r settings m ade when running the out-of-the -box functionality program or “custo m” for settings made when running a custom program) and System Configuration.
Multimedia Presentation System 300 Crestron MPS-300 Uploading and Upgrading Crestron recommends using the latest pr ogramming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attem p ting to upl oad or upgrade it is necessary to establish communicat ion.
Crestron MPS-300 Multimedia Presentation System 300 TCP/IP Ethernet Communication PC RUNNING CRESTRON TOOLBOX MPS-300 ETHERNET • Establish USB comm unications between the MPS-300 and a PC. • Enter the IP ad dress, IP ma sk and de fault router of the MPS-300 via the Crestron Toolbo x ( Functions | Ethernet Addressing ); otherwi se enable DHCP.
Multimedia Presentation System 300 Crestron MPS-300 Configuration & Operation The MPS-300 can be used f or audio a nd video s w itching without any programm ing required. This i s ideal for those that need a basic audio- video s witching syst em. Prior to operation, the MPS-30 0 must be configured for use.
Crestron MPS-300 Multimedia Presentation System 300 Exit the Menu To exit the menu: • While in the main menu, press th e MENU button to exit the menu. Exit Menu Prompt Exit Setup Menu? Yes No ⇒ Press the soft button labeled Yes to exit the menu or press the soft button labe led No to return to the menu.
Multimedia Presentation System 300 Crestron MPS-300 The menu is separated int o four section s. • Audio Setup: Contains co ntrols for PROGRAM , SPEECH , and RECORD out put settings, source in put compensat ion, mast er startup volume, and m icrophones.
Crestron MPS-300 Multimedia Presentation System 300 Set the Program Source Mix To set the PROGRAM output’s s ource mix: • Access the Program Out put menu as desc ribed in “Access the Program Output Me nu” on page 38.
Multimedia Presentation System 300 Crestron MPS-300 Program Bass Controls Program Bass 0db • Adjust the Program Bass level with the j and k button s.
Crestron MPS-300 Multimedia Presentation System 300 Set the Program Minimum Volume The Program Minimum Volume control is used to set the lowest volume setting of the PROGRAM output. The RECORD and SPEECH outputs are not affected by changes made to the Program Minimum Volume level.
Multimedia Presentation System 300 Crestron MPS-300 • Adjust the Program Maximum Volume level with the j and k buttons . Press the k button to increase the Program Maximum Volume level. Press the j button to lower the Program Maximum Volume level. The lowest Program Maximum Volume setting is 50%.
Crestron MPS-300 Multimedia Presentation System 300 To adjust the Program Startup Volume level: • Access the Pro gram Output m enu as described on pa ge 38. • Press the k or j buttons until “Startup Vol.” is displayed on the LCD and press ENTER to open the Program Startup Volume control.
Multimedia Presentation System 300 Crestron MPS-300 Set the Speech Source Mix To set t h e SPEECH output’s sour ce mix: • Access the Speech Out put menu as de scribe d in “Access the Speech Output Menu” on page 43.
Crestron MPS-300 Multimedia Presentation System 300 Speech Bass Con trols Speech Bass 0db • Adjust the Speech Bass lev el with the j and k butt ons. Press t he k button to increase the Speech Bass level. Press the j button to lower the Speech Bass level.
Multimedia Presentation System 300 Crestron MPS-300 Set the Speech Delay To set the Speech Delay: • Access the Speech Output m enu as describe d on page 43. • Press the k or j buttons until “Speech Delay” is displayed on the LCD and press ENTER to open the Speech Delay controls.
Crestron MPS-300 Multimedia Presentation System 300 • Press the k or j buttons until the desired mode is displayed on the LCD and press ENTER . The current setting is indicated with an asterisk (*).
Multimedia Presentation System 300 Crestron MPS-300 • Set the SPEECH output’s M inimum and Maxim um Volume l evels to 30% and 70% (respectively) as describe d below. • Set the Startup Volume levels of the “loudest” outputs ( PROGRAM or SPEECH) to 100% as desc ribed on pa ges 42 and 49 so m aximum dy namic range is available.
Crestron MPS-300 Multimedia Presentation System 300 Speech Maximum Volu me Control Spch. Max Volume 75% • Adjust the Speech Max imum Volume level with the j and k butto ns. Press the k button to increase the Speech Maximum Volume level. Press the j button to lower the Speech Maxim u m Volume level.
Multimedia Presentation System 300 Crestron MPS-300 NOTE: While adjusting the Speech Startup Volume level, th e Speech Volume l evel can be adjuste d by turni ng the volum e control clockwise to raise the volume, or counterclockwise to lower the volume.
Crestron MPS-300 Multimedia Presentation System 300 • Press the k or j buttons until the desired setting is displayed on the LCD. The current setting is indicated with an asterisk (*). The following settings are available: ⇒ Aud. Only : Sends the audio signal from the selected source to th e RECORD output .
Multimedia Presentation System 300 Crestron MPS-300 Adjust the Record Startup Volume The Record Startup Volume control is us ed to establish th e RECORD output’s volume level setting when an input is selected. The SPEECH and PROGRAM outputs are not affected by changes m ade to the Record Startup Vol u me level.
Crestron MPS-300 Multimedia Presentation System 300 Select Input to Compensate Input Compensation Input 1 Comp. • To select the input to com pensate, press the k or j buttons until the desired inp ut is dis played and press ENTER . Adjust Compensation Level Input 1 Comp.
Multimedia Presentation System 300 Crestron MPS-300 Master Startup Volume Control Master Startup Vol. 30% • Adjust the Master Startup Volume level with the j and k buttons. Press the k button to increase the Master St artup Volume level. Press the j button to lower the Master Startup Volume level.
Crestron MPS-300 Multimedia Presentation System 300 Microphone Gating Control (MIC 1 shown) Mic 1 Gati ng OFF • Press the k or j buttons until the desired setting is displayed on the LCD and press ENTER to save the setting. The current setting is indicated with an asterisk (*).
Multimedia Presentation System 300 Crestron MPS-300 Switch Microphone Lim iter A microphone limiter can be i ndividually set on each m icrophone input. To swit ch the microphone limiter on or off: • Access the Micro phone menu as desc ribed on page 54.
Crestron MPS-300 Multimedia Presentation System 300 • To exit the Phantom Power con trol without saving chang es, press MENU . Adjust Microphone Gain The gain for each microp hone input ca n be indivi dually set. To a djust the gain of a microphone i nput: • Access the Micro phone menu as desc ribed on page 54.
Multimedia Presentation System 300 Crestron MPS-300 Select Input to Name Sel. Input To Name 1:BNC 1 • Press the k or j buttons until the input to be named is displayed on th e LCD and press ENTER . The cursor is placed a fter the last character in the input name.
Crestron MPS-300 Multimedia Presentation System 300 Select Input Type Menu Sel. Input Type 1:BNC 1 • Press the k or j buttons to select the video input to be configured and press ENTER . The current setting is indicated with an asterisk (*). • Press the k or j buttons until the desired input type is displayed.
Multimedia Presentation System 300 Crestron MPS-300 • Press the k or j buttons until the output to be named is displayed on the LCD and press ENTER .
Crestron MPS-300 Multimedia Presentation System 300 Display the IP Address IP Address [000] 000. 000. 000 • Turn the vol ume control clo ckwise or counterclockwise t o select a number in the left-most section of the IP address. You can also press the k or j buttons to select a number.
Multimedia Presentation System 300 Crestron MPS-300 Set the Default Router The MPS-300 can be configur ed to use a Defaul t Router fo r TCP/IP communications. To set the IP address of the Default Router: • Access the Network Set up menu as described on page 60.
Crestron MPS-300 Multimedia Presentation System 300 • To save the setting and return to the Network Setup menu, press ENTER . To cancel the operation and re turn to the Network Setup menu, press MENU . Set the WINS Mode The MPS-300 can use a WINS serve r to obta in an IP address.
Multimedia Presentation System 300 Crestron MPS-300 Change the Hostname MPS-300-00107EA0122_ DEL INS < > • Turn the vol ume control clo ckwise or counterclockwise (or press the k or j buttons) to select a new letter (upper case or lowercase) or number.
Crestron MPS-300 Multimedia Presentation System 300 Change the Domain Name corporate.company.c DEL INS < > • Turn the vol ume control clo ckwise or counterclockwise (or press the k or j buttons) to select a new letter (upper case or lowercase) or number.
Multimedia Presentation System 300 Crestron MPS-300 Display the MAC Address The MPS-300 can display its MAC address. To view the MAC address: • Access the Network Set up menu as described on page 60. • Press the k or j buttons until “MAC Address” is displayed on the LCD and press ENTER to display the MAC address.
Crestron MPS-300 Multimedia Presentation System 300 Select Function to Name Select Fct. To Name 1:MUTE • Press the k or j buttons until the function to be named is displayed on the LCD and press ENTER . The cursor is placed a fter the last character in the function nam e.
Multimedia Presentation System 300 Crestron MPS-300 ID Devices Prompt Press ENTER to ID all devices. • Press ENTER to continue the identification pro cess, the MPS-300 will clear all device set tings and pr ompt the use r to select the de vice type to be identified.
Crestron MPS-300 Multimedia Presentation System 300 Display the APAD Upgrade Controls Upgrade APAD Yes • To upgra de the APAD , press th e k or j buttons until “Yes” is displayed on the LCD an d press ENTER . The MPS-300 will upgrade the APAD’s firmware (if necessary ) and copy t he required files to the A PAD.
Multimedia Presentation System 300 Crestron MPS-300 NOTE: This inf ormation ca n be viewed usi ng Crestron Toolbox. F or more information, refer to the Crestron Toolbox help file.
Crestron MPS-300 Multimedia Presentation System 300 ⇒ Press the ME NU button to return to the Info menu. • To view a list of connected network devi ces, press the so ft button l abeled NET . Display Connected Network D evices 2E: APAD LCD 6-bu << >> ⇒ Press the k or j buttons to s ee other netw ork devices.
Multimedia Presentation System 300 Crestron MPS-300 Display the Message Controls System log: Top Clear << >> • To scroll through messages in th e log, press the k or j but tons. • To jump to the beginning of th e log, press the soft button labeled Top .
Crestron MPS-300 Multimedia Presentation System 300 Display the Date Controls DATE: 10/16/2006 MO DAY YR ⇒ To set the month, press the soft button lab eled MO . To set the day, press the soft button lab eled DAY . To set the year, press the soft button labeled YR .
Multimedia Presentation System 300 Crestron MPS-300 Restore Default Settings The MPS-30 0 can be restored to its defau lt factory settings from the fron t panel. Users can select to restore the audio settings or to restore th e audio settings, source names, out put names, and function names.
Crestron MPS-300 Multimedia Presentation System 300 Restore Defaults Menu-All Settings Restore Defaults All settings ⇒ Press the k or j buttons until “All setting s” is displayed on the LCD and press ENTER .
Multimedia Presentation System 300 Crestron MPS-300 • Press the k or j buttons until “Front Panel” is displayed on th e LCD and press ENTER to display the Front Panel control. Front Panel Lock Controls Front Panel Lock: On • Press the k or j buttons to toggle between On and Off.
Crestron MPS-300 Multimedia Presentation System 300 Lower the Projection Screen Press the function button labeled SCREEN DOW N to lower the project or screen. NOTE: This function will only work if a projection screen’s control lines have been connected to RELAY 1 (up cont rol) and RELAY 2 (do wn control) .
Multimedia Presentation System 300 Crestron MPS-300 • Lower the volume: Turn the volum e control counte rclockwise. The volume level will be displayed on the LCD. Mute Audio The audio o utput of t he MPS-300 ca n be mute d with the MUTE button. • Mute the audio outpu t: Press the button labeled MUTE .
Crestron MPS-300 Multimedia Presentation System 300 Turn On the System To turn on the system: 1. Press the soft button labeled Source to display a list of available s ources. 2. Turn the Nav Wheel to highlight the desired source ( BNC 1 , BNC 2 , RGBHV 3 , RGBHV 4 , RGBHV 5 , QM IN 6 , QM IN 7 , or QM IN 8 ).
Multimedia Presentation System 300 Crestron MPS-300 Mute Audio The audio o utput of t he MPS-300 ca n be mute d with the A PAD. • To Mute the audio output: ⇒ Press the power butto n ⇒ Press the soft button labeled Mute . The display will indicate that the audio out put is m uted.
Crestron MPS-300 Multimedia Presentation System 300 Control from a Keypad The following describes operation of the system when using the ou t-of-the-box functionality and either a C2N-DB12 or CNX-B12 keypad. If a custo m program has been created, the MPS-300 m ay functio n different ly.
Multimedia Presentation System 300 Crestron MPS-300 Control from a C2N-FTB The following describes operation of the system when using the ou t-of-the-box functionality and a C2N-FTB FlipTop Control Cen ter. If a custom program has been created, the MPS-300 may function di fferently.
Crestron MPS-300 Multimedia Presentation System 300 Adjust the Volume Level To raise the volume level, press the VOL UP button. To lower the volume, press the VOL DOWN button. The volume control buttons will only co ntrol the volume parameter that was selected when the Volume Control Mode was specified as described on page 46.
Multimedia Presentation System 300 Crestron MPS-300 Problem Solving Troubleshooting The following table provides corrective action for possible trouble situ ations. If further assistance is required, please contact a Crestron custom er service representative.
Crestron MPS-300 Multimedia Presentation System 300 NOTE: If com munication ca nnot be esta blished or the control system is locked-up, refer to “Troubleshooting Commun ications” in the Crestron 2- Series Control Systems Reference Guide (Doc. 6256).
Multimedia Presentation System 300 Crestron MPS-300 Make sure to choose USB as the “Connection Ty pe”, then click OK . The following text will appear in the bottom right corner of the “Text Console” window: usb;device 2SeriesCtrlSy stemMonitor The following text will appear in Toolbox: MPSMNTR> 10.
Crestron MPS-300 Multimedia Presentation System 300 Calculate Power CAUTION: Use only Crestron power supplies for Crestron equipment. Failure to do so coul d cause equipm ent damage or void the Crestron war ranty. CAUTION: Provide sufficient power to the syst em.
Multimedia Presentation System 300 Crestron MPS-300 List of Related Reference Documents DOCUMENT TITLE 2-Series Control Systems Ref erenc e Guide APAD Wall Mount LCD Controller C2N-DB12 12-Button Deco.
Crestron MPS-300 Multimedia Presentation System 300 Software License Agreement This License Agreement (“Agree ment”) is a legal contract betw een you (either an individual or a single business entity) and Crestron Electronics, Inc.
Multimedia Presentation System 300 Crestron MPS-300 If You are a business or organization, You agree that upon request from Crestron or its authorized agent, You will within thirty (30) days fully doc.
Crestron MPS-300 Multimedia Presentation System 300 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise m ay be returned for credit, ex change or service witho ut prior authorization from CR ESTRON. To obtai n warranty serv ice for CREST RON products, contact an authorized CRESTRON deal er.
Crestron Electronics, Inc. Operations Guide – DOC. 6529B 15 Volvo Drive Rockleigh, NJ 0764 7 (2016141) Tel: 888.CRESTRON 1 0.08 Fax: 201.767.7576 Specific ations subject to www.
デバイスCrestron Multimedia Presentation System 300 MPS-300の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Crestron Multimedia Presentation System 300 MPS-300をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCrestron Multimedia Presentation System 300 MPS-300の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Crestron Multimedia Presentation System 300 MPS-300の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Crestron Multimedia Presentation System 300 MPS-300で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Crestron Multimedia Presentation System 300 MPS-300を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCrestron Multimedia Presentation System 300 MPS-300の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Crestron Multimedia Presentation System 300 MPS-300に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCrestron Multimedia Presentation System 300 MPS-300デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
