Crimestopper Security ProductsメーカーCS-2002DCの使用説明書/サービス説明書
ページ先へ移動 of 20
CS-2002DC Series IV REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an “On-Guard” Remote Al arm System by Crimestopper Security Products Inc. This booklet contains the information nec essary for installing, using, and maintaining your alarm system.
TABLE OF CONTENTS Installation Cautions & Warnings…….……………………………….……………………………………………2 Control Module & Component M ounting……………...……………………..……………………….
CONTROL MODULE & COMPONENT MOUNTING DO NOT Mount the control unit in the engine comp artment or where the control unit or wiring harness where they can become entangled with moving par ts such as brake/gas/clutch pedals, or the steering column! The alarm control module s hould be mounted in a concealed location.
WIRING BLACK WIRE: SYSTEM CHASSIS GROUND The Black wire MUST be connected t he CHASSIS METAL of the vehicle. Scrape away any paint or debris from the connection point and use a star washer to ensure a good connection.
WIRING BLUE/WHITE WIRE: (-) PASSENGER(S) DOOR UNL OCK OUTPUT (Optional, requires relay ) Connects to unlock circuit for passenger door(s) when using separate driver’s door unlock option. See SEPARATE DRIVER’S DOOR UNLOCK WIRING on Page 8 for some configuration options.
WIRING RED WIRE: +12V POWER INPUT (15 amp fuse) Connect to +12 Volt source with supplied fuse & holder. Recommended location for this connection is at the vehicle battery positive terminal. 14 GA. BROWN WIRE: (On-board Starter Disable Relay) Cut the 14GA.
NEGA TIVE TRIGGER DOORLOCK WIRING POS ITIVE TRIG GER DOO RLOCK WIRIN G GREEN GREEN FU SED RED +12V RED BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FAC TO RY FAC TO RY L L POWER POWER LOCKING LOCKING U.
SEPARATE DRIVER’S DOOR UNLOCK WIRING NEGA TIVE T RIGGER DOOR LOCKS BLUE/W HIT E GREEN RED BLUE DRIVER'S DOOR MOTOR 86 85 L L 87 UL UL 87A 30 F ACTOR Y LOCK RELA YS +12V + FUSED UNLOCK W IRE CUT.
TRANSMITTER PROGRAMMING NOTE: All transmitters must be learned at the time of programming. This system can learn up to 4 remotes. 1. Turn key to the ON position and press program button 4 times. 2. After a short delay, the unit will flash the parking lights 4 times.
OPTION PROGRAMMING 1. Turn the Ignition ON and press the Override/Program button 5 times. 2. After a short delay, the parking lights will flash 5 times and status LED will be on solid. 3. Within the next few seconds, press the Override/ Program button [again] the number of times that corresponds to the options chart below.
OPTION PROGRAMMING 1. HORN CHIRPS / PULSES This option controls the system’s Factory Vehicle H orn output. There are 3 selections: Button 1 (Lock) = Horn Pulse only when alarm is tripped. Button 2 (Unlock) = Horn Chirps for Arm / Disarm and Pulse when tripped.
OPTION PROGRAMMING 7. DOUBLE UNLOCK PULSE With this feature enabled, the unit will send 2 unlock pul ses when the #2 Unlock button is pressed. 2 pulses are required for interfacing into some existing Factory Keyless Entry or Alarm systems on vehicles such as Nissan, VW, Toyota, and Lexus vehicles.
PROGRAMMABLE OPTION RESET Follow the steps below to reset ALL OPTION VAL UES ON PAGE 10 TO FACTORY DEFAULT SETTINGS. 1. Turn the Ignition ON and press the Override/Program button 5 times. You should hear a long chirp. 2. Immediately press Button #3 (Trunk) on the remote.
OPERATING INSTRUCTIONS 6 BUTTON REMOTE TRANSMITTER: #3 #1 #2 #4 LOCK TR U N K PA N I C UNLOCK BA N K #2 FLA SH LIGHT (A U X.) PAN I C BANK #1 (Directly Press Buttons) Button 1: Arm Button 2: Disarm Bu.
OPERATING INSTRUCTIONS TRUNK/HATCH POP (REMOTE AUX. OUTPUT 1, OPTIONAL) To pop the trunk (if optional feature is installed), press Button #3 (Trunk Symbol) on the transmitter for at least 1½ seconds. If the system is armed, pressing Button #3 may or may not trip the alarm system when opening the trunk depending on programming option (10).
OPERATING INSTRUCTIONS VALET MODE To disable the Alarm system for vehicle serv ice or otherwise, turn the ignition on and press the override/program button 4-5 seconds until the dash LED t urns on solid and you hear (1) siren chirp. Repeat the process to exit VALET mode and the system will ch irp (2) times and the LED will turn off.
OPERATING INSTRUCTIONS ACTIVE RE-ARMING (FAIL-SAFE PROTECTION) Active Re-arming means that the system will re-arm itself 30 seconds after disarmed with the transmitter if a door has not yet been opened. This is handy if the vehicle is accidenta lly disarmed (via the transmi tter in your pocket) without you knowing it.
CARJACK PROTECTION FEATURES FULL-TIME CARJACK ONLY USE THIS MODE WHEN THERE IS AN EXTREME TREAT OF A CARJACK WITH YOUR VEHICLE. Full-time Carjack protection must be enabled before use through Alarm programming options (13) & (14).
+ - + BLACK(GROUND ) W H ITE( W ARN ING) RED (+) BLUE (TRIGGER) RED WHIT E BROWN BLUE/WHITE WHIT E/R ED ORANGE BLACK/WHITE BLUE GRA Y YELLOW BLACK VIOLET GREEN LED OVERRIDE/ PROGRA M BUTTO N BA TTERY (-) LOCK OUTPUT +12 VOL T FOR RELA YS (-) UNLOCK OUTPUT GREEN BLUE RED (-) NEG .
ONLINE TECHNICAL SUPPORT www.crimestopper.com/techweb03.html www.crimestopper.com email@crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2003 Crimestopper Security Products.
デバイスCrimestopper Security Products CS-2002DCの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Crimestopper Security Products CS-2002DCをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCrimestopper Security Products CS-2002DCの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Crimestopper Security Products CS-2002DCの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Crimestopper Security Products CS-2002DCで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Crimestopper Security Products CS-2002DCを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCrimestopper Security Products CS-2002DCの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Crimestopper Security Products CS-2002DCに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCrimestopper Security Products CS-2002DCデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。