Crimestopper Security ProductsメーカーTN-4003の使用説明書/サービス説明書
ページ先へ移動 of 12
Installation Instructions TRACKNET ™ TN - 4003 /4004.
2 TABLE OF CONTENTS TABLE OF CONTENTS Introduction .............................................. ............................................................. .. ....................... 2 Installation Caution and Warnings .......... .................
3 INSTALLATION CAUTIONS & WARNINGS BEFORE BEGINNING , check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, ENGINE COMPUTER S, and BATTERY etc.). WE RECOMMEND the use of a VOLT/OHM METER to test and verify wiring circuits.
4 CONTROL MODULE & COMPONENT MOUNTING Main Unit: The TrakNet unit has an internal power management program that monitors the vehicle power at all times. The internal power management program is continuously looking at the condition of the battery in order to detect the state of the vehicle operation.
5 MOUNTING LOCATION Selecting the Antenna Locations The Module requires two antennas elements. One antenna is for receivin g GPS signals from The Navistar GPS satellites. The second antenna is a radio trans ceiver antenna that communicates with the Cellular network.
6 INSTALLATION Locating Vehicle Power The TRAKNET has an internal power management program that monitors the vehi cle power at all times. The internal power management program is continuously looking at the condition of the vehicle battery in order to detect the state of the vehicle operation.
7 INSTALLATION Within five minutes the flash rate will change to approximately one second on and one second off to indicate that the GPS Receiver has established a location “lock”. Within 1 minute the flash color should be green to indicate good cellular coverage.
8 LED STATUS INDICATOR LED Status Indicator BI - COLOR ON BOARD LED: This unit has a bi - colored LED on unit. SOLID LED C OLOR: Solid Green – Device is in Test Mode: no inputs are currently being triggered. Solid Orange – Device is in Test Mode: At least one input is currently being triggered.
9 WIRING NOTE: Some Options Need to Be Pre - programmed From Crime s topper prior to installing the unit. Pin 1 Black: Chassis Ground Input THIS WIRE MUST BE CONNECTED TO TH E CHASSIS METAL OF THE VEHICLE. Scrape away any paint or dirt to ensure a good connection.
10 WIRING Pin 12 Orange: Alarm Trigger ( -) Default * or Door Open/Close Input #1 A. Alarm Trigger * : Triggers a larm input of tracking device if received a nega tive input for 15 seconds or longer. This is connected to the negative siren output , if alarm has positive siren output use a relay to convert to negative .
11 WIRING DIAGRAM.
ACCESS INFORMATION Cong ratulations, you have just installed the Internet based vehicle telematics system. Now that it’s installed, here’s how to use your system. Step #1 First fill out your TrakNet registration form and fax to 805.581 - 9500. Then you will receive a call or emai l with your login and password.
デバイスCrimestopper Security Products TN-4003の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Crimestopper Security Products TN-4003をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCrimestopper Security Products TN-4003の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Crimestopper Security Products TN-4003の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Crimestopper Security Products TN-4003で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Crimestopper Security Products TN-4003を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCrimestopper Security Products TN-4003の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Crimestopper Security Products TN-4003に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCrimestopper Security Products TN-4003デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
