Cub Cadetメーカー945 SWEの使用説明書/サービス説明書
ページ先へ移動 of 28
CUB CADET LLC, P .O . BO X 36 1 1 3 1 CLEVE LAND, OHIO 4 4 1 36 - 0 0 1 9 Print ed In US A O p e r a t O r ’ s M a n u a l Safe Ope ration Practices • S et-Up • Ope ration • Maintenan ce • S.
T o The Own er 1 2 Record Product Information Befo re set ting up a nd ope rating your new e quipm ent, ple ase loc ate the mode l plate on the e quipm ent and record t he informati on in the prov ided ar ea to the right.
Im por tan t Safe Ope ra ti on Pr ac ti ces 2 3 T raining Read, un ders tan d, and foll ow all instru cti ons on the 1 . machine an d in the manual(s ) be fore at tempting to assembl e and op erate. Keep this manu al in a safe p lace for future an d regular re feren ce and for ord ering re placeme nt par ts .
4 s e c t i O n 2 — i M p O r t a n t s a f e O p e r a t i O n p r a c t i c e s Safe Handling of G asoline T o avoid pe rsona l injur y or prop er t y dama ge use ex t reme car e in handling gas oline. Gas oline is e x treme ly f lammab le and the vapo rs are e xplosi ve.
5 s e c t i O n 2 — i M p O r t a n t s a f e O p e r a t i O n p r a c t i c e s Maintena nce & St orage Never tamp er with s afet y d evices. Che ck their p roper 1 . oper ation re gularly. Refer to the maintenan ce and adjustm ent sec tio ns of this manual.
6 s e c t i O n 2 — i M p O r t a n t s a f e O p e r a t i O n p r a c t i c e s Safet y Symbols This pa ge depi ct s and des cribe s safet y s ymb ols that may app ear on this pro duc t. Re ad, und ers tand, an d follow all ins truc tio ns on the machine b efore at tempt ing to assembl e and op erate.
Secure the upp er handle and lower handl e with the two wing 4. nuts an d carria ge bol ts rem oved earlier. Tighten the t wo wing nut s already i nstall ed in the up per ho les to f irml y secure th e uppe r handle an d suppo r t tubes . See Figure 3 - 2.
Place chute assembl y onto chute base as show n in Figure 3-5. Make sure that the chute notches e ngage w ith the spir al end of chute direc tio nal control, and th e t wo f lange kee per s are bene ath the f lange o n the chute bas e. Secure f l ange keep er rem oved earlier w ith lock nu ts and sc rews.
Auger and Driv e Control Cables W ARNI NG! Pri or to ope rating your snow thrower, caref ully read an d follow all ins truc tio ns below. Perf orm all adjus tment s to verif y you r snow thrower is oper ating saf ely and p roper ly .
W ARNI NG! D o not over-tighten the cabl e. Over- tightening may prevent the aug er fro m disenga ging and comprom ise the sa fet y of the sn ow thrower . If adjus ting the auge r cabl e, thread the lo ck nut down to 4 . length en the c able as ne cessar y to s top the auge r from turning w hen the contro l is release d.
Snow thrower controls and f eatures are des cribe d bel ow and illustrate d in Fig. 4 - 1. NOTE: For de taile d inform ation on all en gine controls , refer to the sep arate Briggs & Strat ton Engin e Op erator ’s Manual.
Primer Bulb Pressing the pr imer bulb f orces fue l direc tly into the e ngine’s carbur etor to aid in st ar ting a “Cold ” engin e. NOTE: D o not use the p rimer b ulb to restar t a warm eng ine af ter a shor t shutdow n. Oil Fil l Engine oil leve l can be ch ecked and o il adde d through th e oil f ill.
T wo- W ay Chut e Control™ The t wo -w ay chute control is loc ated on the l ef t side o f the dash pane l and is used to contro l the dist ance of snow dischar ge from the chute. T o chang e the upp er chute angle to contro l the dist ance • that snow is thrown, pi vot the lever for w ard or back w ard.
Starting The Engine Atta ch spark plu g wire to spark p lug. Make cer t ain the 1 . met al loop o n the end o f the spark p lug wire (inside t he rubb er bo ot) is fastene d se curely over the m etal tip o n the spark plu g. Make cer tain b oth the auge r control and dri ve control are 2.
Operating Tips NOTE : Allow the en gine to warm up f or a few minutes . The engine w ill not develo p full p ower until it reaches o peratin g temperature. W ARNI NG! T he temp erature of th e muf f le r and the surroun ding areas may excee d 1 50 ° F .
With the m ounting ho les toward the b ack , slide th e new 4. shave plate into position and s ecure wi th the fas tener s removed prev iously. Lubric ation Gear Shaft The g ear (hex) s haf t shoul d be lubri cated at leas t once a seas on or af ter ever y t went y -f ive (25) hours of op eration .
Figur e 6 -5 Auger S haf t At least once a seas on, on e at a time, remove the she ar pins from the auge r shaf t. Spr ay lubricant insid e the hub of each au ger spiral asse mbly an d around the sp acers o n the auger sh af t. Grease f it tin gs can also b e found at each e nd of the au ger shaf t .
Refe r to “ Auger and D ri ve Cont ro l Cab les ” of the A ssembl y & Set-Up - Sec tio n 3 for instr uc tions to adjus t the drive control . T o f ur ther check th e adjustm ent, pro ceed as fo llows: With the sn ow thrower tippe d for wa rd (be cer ta in to drain 1.
Belt Replac ement Belt Remo val Preparat ion Disconnect the chute crank assembly at the discharge 1 . chute end by remo ving the hairpin clip and the flat washer . Re fer to Figure 7 - 1 . Remove the h ex s crews and lo ck nuts securing the for ward 2.
Slip the auger con trol belt (the front belt) off the en gine 2. pulley . Pull the 3. brake bracket assembly t owards the cable guide roller and unhook the auger cable “Z” f it ting. Ref er to Figure 7 -5. F rom both sides of the frame assembly , use a 1 /2" wrench 4.
If also replacing the drive belt, proceed to the “ Drive Belt ” 1 1 . instruction . If not, reposition the transmission frame back onto the auger housing. In stall the drive belt on the engine pulley , re - connec t the auger cable “Z” f itting and auger idler ro d ferrule to the brake bracket.
Slide the bearing onto the left e nd of the hex shaf t and 1 4. press int o the hole on the lef t side the frame. Plac e the belleville washer (rounded side to ward head) 1 5. onto the hex screw remov ed earlier , and insert the screw int o the threaded hole of the he x shaf t.
Of f - Season Storag e If the snow throw er will not be used for 30 days or longer , the equipment needs to be stored prop erly . Follow storage instructions be low to ens ure top per formance from the snow thro wer for many more years.
24 Problem Cause Remedy Engine fa ils to star t Choke control not in O N positio n. 1. Spark plu g wire disconn ec ted. 2. Fuel tank empt y o r stal e fue l. 3. Engine not p rimed . 4. F ault y spark p lug. 5. Safet y key not i nser ted . 6. Move choke control to ON p osition .
R epl ac em en t P ar ts 9 25 Component Description P art Number Ex tension Cord, 1 1 0V 929 - 0 0 71 Auger Drive Belt 9 5 4 - 0 4131 Wheel D rive Belt 95 4 - 0 3 67 F ric tion Wheel A ssembly 9 1 8 - 0 417 8 F ric tion Wheel w/Bonde d Rubber 718 - 0 4 0 3 4 Halogen L amp, 1 2V , ( #890) 7 2 5 -16 5 8 Shear Pin, 1 .
No te s 10 26.
27 s e c t i O n 1 0 — n O t e s.
Th e lim it ed w ar r an t y se t for t h be low i s gi ven b y Cub C ad et L LC w i th re sp ec t to n ew m er ch and is e pur ch as e d and u se d in t he Un it ed S t a te s, it s p os se ss io ns .
デバイスCub Cadet 945 SWEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Cub Cadet 945 SWEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCub Cadet 945 SWEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cub Cadet 945 SWEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cub Cadet 945 SWEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cub Cadet 945 SWEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCub Cadet 945 SWEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cub Cadet 945 SWEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCub Cadet 945 SWEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
