CulliganメーカーAqua-Cleer Aqua-Cleer Advanced Drinking Water Systemsの使用説明書/サービス説明書
ページ先へ移動 of 59
Culligan ® Aqua-Cleer ® Advanced Drinking Water Systems Owners Guide.
THANK YOU AND WELCOME TO YOUR NEW WORLD OF BETTER LIVING WITH CULLIGAN WATER. Notice: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.
Table of Contents 3 A b o u t Y o u r S y s t e m ................................................. 4 I n s t a l l a t i o n ........................................................ 7 H o w t o M a i n t a i n Y o u r S y s t e m ....................
Chapter Heading 4 About Your System Thank you for choosing a Culligan Aqua-Cleer advanced drinking water system. Your new system is designed to bring you years of deliciously crystal-clear Culligan water. The best part is it comes right from the tap. No more lugging around bottles or waiting for pitchers to slowly fill up.
5 Sequence of Filtration Type of Filtration Specification Advanced Filtration Total Defense Arsenic Perchlorate* Speciality Carbon Block Specialty Media 1 Specialty Media 1 Post-Filtration Carbon Gran.
6 • Chloramines have a stronger taste and are more difficult to remove than chlorine. • Mercury is a toxin that can cause kidney damage. • Lead is a toxin that can cause kidney problems or high blood pressure in adults and developmental problems in children.
Chapter Heading 7 T o Bottom Of RO Cartridge Aqua-Cleer Faucet Monitor Sensor Monitor Ball V alve T ank Drain Drain Line from Air Gap to Drain (3/8” T ubing) Cold Water Supply Post Filter 3/8” T u.
8 Important considerations: • Access to the bottom (under sink) of the faucet is required for attachment of product water line. • The faucet can be installed for left- or right-handed operation.
9 3. Repeat steps 1-3 and install the flushed activated carbon filter cartridge into housing and the RO membrane element. Be sure the drain adapter is in place. Note: 1) The RO cartridge must be inserted into the 2nd, 3rd, or 4 th position on the RO manifold.
10 component of feed water will plug a membrane over time. Use of a softener will reduce the fouling effect on a membrane. One way to detect too much hardness in the feed water is the weight of a membrane installed for a period of time. A fouled membrane (dried) will weigh significantly more than a new membrane.
Chapter Heading 11 To keep the Aqua-Cleer® system operating properly, it is necessary to change the filters and sanitize the system periodically. Typically, this should be done on an annual basis. Service frequency may vary depending on local water conditions.
12 Preliminary Steps: 1. Check for any leaks that may exist from tubing connections or the faucet. 2. Check for flow to the drain. If flowing, close tank shut-off so you can check auto shut-off operation 3. Test and record product TDS from faucet. Also observe if faucet stem is stiff to move.
Chapter Heading 13 Parts List Item Description 1 Manifold Assembly 2 5 Micron Sediment Filter 10 Micron Sediment Filter 25 Micron Sediment Filter 3 Carbon Block Filter Granular Activated Carbon Filter.
Chapter Heading 14 Important Notice: Read this Performance Data Sheet and compare the capabilities of this system with your actual water treatment needs. It is recommended that, before installing a water treatment system, you have your water supply tested to determine your actual water treatment needs.
15 Total Defense (TD) The Total Defense has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in the water ent.
16 Organic Chemicals Included in Surrogate Testing: Applies to Total Defense (TD) only. Substance Inuent Challenge Concentration mg/L Maximum permissible product water concentration mg/L Alachor 0.050 0.001 Atrazine 0.100 0.003 Benzene 0.081 0.001 Carbofuran 0.
17 Organic Chemicals Included in Surrogate Testing (Continued): Applies to Total Defense (TD) only. Substance Inuent Challenge Concentration mg/L Maximum permissible product water concentration mg/L Styrene 0.150 0.001 1,1,2,2-Tetrachloroethane 0.081 0.
Chapter Heading Inside Text 18 RO30 This system has been tested according to NSF/ANSI 58 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 58.
Chapter Heading 19 Performance Data Sheet (con’t) RO30 with TD These systems have been tested and certified by NSF International according to NSF/ANSI 42, 53, and 58 for the reduction of the substances listed below.
20 Total Defense (TD) The Total Defense has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in the water ent.
21 Organic Chemicals Included in Surrogate Testing: Applies to Total Defense (TD) only. Substance Inuent Challenge Concentration mg/L Maximum permissible product water concentration mg/L alachor 0.050 0.001 atrazine 0.100 0.003 benzene 0.081 0.001 carbofuran 0.
22 Substance Inuent Challenge Concentration mg/L Maximum permissible product water concentration mg/L simazine 0.120 0.004 styrene 0.150 0.001 1,1,2,2-tetrachloroethane 0.081 0.001 tetrachloroethlene 0.081 0.001 toluene 0.078 0.001 2,4,5-TP (silvex) 0.
23 RO30 with AS3 These systems have been tested and certified by NSF International according to NSF/ANSI 53 and 58 for the reduction of the substances listed below.
24 AS3 The AS3 has been tested according to NSF/ANSI 53 for the reduction of the substances listed below. The concentration of the indicated substances in the water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 53.
25 RO30 with AS3, TD These systems have been tested and certified by NSF International according to NSF/ANSI 42, 53, and 58 for the reduction of the substances listed below.
26 AS3 The AS3 has been tested according to NSF/ANSI 53 for the reduction of the substances listed below. The concentration of the indicated substances in the water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 53.
27 Total Defense (TD) The T otal Defense has been tested according to NSF/ANSI 42 and 53 for the reduction of the sub- stances listed below . The concentration of the indicated substances in the water.
28 Organic Chemicals Included in Surrogate Testing: Applies to Total Defense (TD) only. Substance Inuent Challenge Concentration mg/L Maximum permissible product water concentration mg/L alachor 0.050 0.001 atrazine 0.100 0.003 benzene 0.081 0.001 carbofuran 0.
29 Substance Inuent Challenge Concentration mg/L Maximum permissible product water concentration mg/L simazine 0.120 0.004 styrene 0.150 0.001 1,1,2,2-tetrachloroethane 0.081 0.001 tetrachloroethlene 0.081 0.001 toluene 0.078 0.001 2,4,5-TP (silvex) 0.
30 RO50 This system has been tested according to NSF/ANSI 58 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 58.
31 Performance Data Sheet (con’t) RO50 with TD These systems have been tested and certified by NSF International according to NSF/ANSI 42, 53, and 58 for the reduction of the substances listed below.
32 Performance Data Sheet (con’t) Total Defense (TD) The Total Defense has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below.
33 Performance Data Sheet (con’t) Organic Chemicals Included in Surrogate Testing: Applies to Total Defense (TD) only. Substance Inuent Challenge Concentration mg/L Maximum permissible product water concentration mg/L alachor 0.050 0.001 atrazine 0.
34 Substance Inuent Challenge Concentration mg/L Maximum permissible product water concentration mg/L styrene 0.150 0.001 1,1,2,2-tetrachloroethane 0.081 0.001 tetrachloroethlene 0.081 0.001 toluene 0.078 0.001 2,4,5-TP (silvex) 0.270 0.002 tribromoacetic acid 0.
35 RO50 with AS3 These systems have been tested and certied by NSF International according to NSF/ANSI 53 and 58 for the reduction of the substances listed below .
36 AS3 The AS3 has been tested according to NSF/ANSI 53 for the reduction of the substances listed below . The concentration of the indicated substances in the water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specied in NSF/ANSI 53.
37 RO50 with AS3, TD These systems have been tested and certied by NSF International according to NSF/ANSI 42, 53, and 58 for the reduction of the substances listed below .
38 AS3 The AS3 has been tested according to NSF/ANSI 53 for the reduction of the substances listed below . The concentration of the indicated substances in the water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specied in NSF/ANSI 53.
39 Total Defense (TD) T otal Defense has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below . The concentration of the indicated substances in the water enter.
40 Organic Chemicals Included in Surrogate Testing: Applies to Total Defense (TD) only. Substance Inuent Challenge Concentration mg/L Maximum permissible product water concentration mg/L alachor 0.050 0.001 atrazine 0.100 0.003 benzene 0.081 0.001 carbofuran 0.
41 Substance Inuent Challenge Concentration mg/L Maximum permissible product water concentration mg/L simazine 0.120 0.004 styrene 0.150 0.001 1,1,2,2-tetrachloroethane 0.081 0.001 tetrachloroethlene 0.081 0.001 toluene 0.078 0.001 2,4,5-TP (silvex) 0.
42 Performance Data Sheet (con’t) Output (T otal Dissolved Solids (TDS) Reduction and Output Production) 1 – RO30 Tank Size 2 gallon 3 gallon 9 gallon Product System Daily Prod. Rate To Pressurized Storage Tank 1 1.09 gpd 1 1.09 gpd 1 1.09 gpd Prod.
43 AS3 The AS3 has been tested according to NSF/ANSI 53 for the reduction of the substances listed below. The concentration of the indicated substances in the water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 53.
Chapter Heading 44 The Aqua-Cleer Advanced Drinking Water System with CB or GAC cartridge has been tested and certified by NSF International against NSF/ANSI Standard 42 for the effective reduction of aesthetic Chlorine Taste and Odor, the TD cartridge for the effective reduction of aesthetic Chlorine Taste and Odor and Nominal Particulate Class 1.
45 California Certificates CA Certificates - Placeholder.
46 California Certificates CA Certificates - Placeholder.
47 California Certificates CA Certificates - Placeholder.
48 California Certificates CA Certificates - Placeholder.
49 California Certificates CA Certificates - Placeholder.
50 California Certificates CA Certificates - Placeholder.
51 California Certificates CA Certificates - Placeholder.
52 California Certificates CA Certificates - Placeholder.
53 California Certificates CA Certificates - Placeholder.
54 Arsenic Fact Sheet Arsenic (abbreviated As) is found naturally in some well water. Arsenic in water has no color, taste or odor. It must be measured by a lab test. Public water utilities must have their water tested for arsenic. You can get the results from your water utility.
55 Arsenic Fact Sheet (con’t) Arsenic (As) is a naturally occurring contaminant found in many ground waters. It generally occurs in two forms (valences or oxidation states): pentavalent arsenic (also known as As(V), As(+5), and arsenate) and trivalent arsenic (also known as As(III), As(+3), and arsenite).
56 Troubleshooting Guide.
57 Troubleshooting Guide (con’t).
58 Model Serial No. Date Installed For Service Call Culligan at: ( ) - Cartridge(s) Changed Date Serviced Sediment Filter Activated Pre-Carbon Filter RO Membrane Activated Post-Carbon Filter Sanitized.
59 Culligan Lifetime Limited Warranty Culligan Aqua-Cleer Advanced Drinking Water System You have just purchased one of the finest drinki ng wate r syste ms made.
デバイスCulligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water Systemsの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water Systemsをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCulligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water Systemsの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water Systemsの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water Systemsで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water Systemsを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCulligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water Systemsの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water Systemsに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCulligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water Systemsデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
