Curtis MathesメーカーCMC13003の使用説明書/サービス説明書
ページ先へ移動 of 42
TV/VCR Combination Unit Owner s Manual CMC13003 AA68-00951A/eng 10/26/00 8:52 AM Page i.
i. I MPOR T ANT S AFETY I NSTRUCTIONS I MPOR T ANT S AFETY I NSTRUCTIONS Save These Instructions Warning! Important Safety Instructions CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE P ARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ii. I MPOR T ANT S AFETY I NSTRUCTIONS I MPOR T ANT S AFETY I NSTRUCTIONS Save These Instructions Important Safety Information, continued • Do not place the TV/VCR on an unstable cart, stand, tripod, bracket, or table. The TV/VCR may fall, causing serious injury to a child or adult, and serious damage to the unit.
Important Safety Information, continued • Ground outdoor antennas. If an outside antenna or cable system is connected to the TV/VCR, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.
C ONTENTS iv C ONTENTS Chapter 1: Learning About Y our New TV/VCR ..................1 List of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Checking Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
v. C ONTENTS C ONTENTS Chapter 5: Special Features .................................................23 Viewing the Demonstration Mode . . . . . . . . . . . . . . . . . . . 23 Using T urbo Rewind . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Features Y our TV/VCR was designed and engineered using the latest technology . This TV/VCR is a full-featured, high-performance unit that not only meets, but exceeds, industry standards.
Understanding the Controls Front Panel Jacks Front Panel Controls L EARNING A BOUT Y OUR N EW TV/VCR 2 C HAPTER O NE : L EARNING ABOUT Y OUR N EW TV/VCR AA68-00951A/eng 10/26/00 8:52 AM Page 2.
Understanding the Controls, continued The buttons on the front panel control basic features. For more advanced features, you will use the remote control. 1 EARPHONE jack - Connect a set of earphones (with a mini connector) to this jack. 2 VIDEO and AUDIO IN jacks - Connect components, such as a camcorder , to these jacks.
4 C HAPTER O NE : L EARNING ABOUT Y OUR N EW TV/VCR L EARNING A BOUT Y OUR N EW TV/VCR Understanding the Controls, continued Rear Panel 1 VHF antenna mount VHF rod antenna mount. See page 6. 2 Antenna terminal Use this terminal (VHF/UHF IN FROM ANT) to connect the TV/VCR to a 75-ohm outdoor antenna or cable system.
5 C HAPTER O NE : L EARNING ABOUT Y OUR N EW TV/VCR L EARNING A BOUT Y OUR N EW TV/VCR Understanding the Controls, continued Remote Control Use the remote control within 33 feet (10 meters) of the TV/VCR and point it directly at the TV/VCR. 1 POWER Press to turn the TV/VCR on and off.
6 C HAPTER T WO : I NST ALLA TION C HAPTER T WO I NST ALLA TION Connecting VHF and UHF Antennas If you do not have cable TV , you must connect an antenna to your TV/VCR.
7 C HAPTER T WO : I NST ALLA TION I NST ALLA TION Connecting VHF and UHF Antennas, continued If you use a 300-ohm antenna with twin flat leads, follow the directions below , but skip step 1. 1 Push the stem of the rod antenna into the antenna mount. 2 Connect both antenna leads to the combiner .
I NST ALLA TION 8 C HAPTER T WO : I NST ALLA TION Connecting Cable TV Systems to the TV/VCR, continued 2 Connect one of the coaxial cables between the splitter and the input on the converter box. 3 Connect a second coaxial cable between the output of the converter box and the “B” input on the RF (A/B) switch.
9 C HAPTER T WO : I NST ALLA TION I NST ALLA TION Installing Batteries in the Remote Control 1 Open the battery cover by pressing on the back cover’ s tab and lifting up. 2 Install two AA size batteries. Make sure to match the + and – ends of the batteries with the diagram inside the compartment.
10 C HAPTER T HREE : TV O PERA TION C HAPTER T HREE TV O PERA TION Viewing the On-screen Display The on-screen displays automatically appear on the screen when you turn the TV/VCR on or change its status (from stop to play , from play to stop, etc.). Y ou can also activate the on-screen displays manually by using the remote control.
11 C HAPTER T HREE : TV O PERA TION TV O PERA TION Selecting the Signal Source The first step in programming your TV/VCR is to select the signal source of your antenna or cable TV system. 1 With the main menu on the screen, press CH until “Setup” is highlighted.
Programming the Channels, continued • When entering single-digit channels, press 0 first. For example, to select channel 8, press 0, then 8. • When entering three-digit channels, press the +100 button on the remote control first. For example, to select channel 104, press +100, then press 0, then 4.
Setting the Clock, continued 4 Press VOL+. 5 Press CH or CH to set the current minute. Setting the date 1 Press VOL+. The month will blink. 2 Press CH or CH to set the current month. 3 Press VOL+. The day will blink. 4 Press CH or CH to set the current day .
Setting the Clock, continued ✔ While “T ime Zone” is selected, press either the VOL + or the VOL - button to change the T ime Zone. Sequence : A TL., HAW ., ALAS, PAC., MTN., CEN., EAST . 7 Press CH button to select the “DST”(Daylight Savings T ime) field.
Setting the Sleep T imer The sleep timer automatically turns off the TV/VCR at the time you select. This is convenient if you like to fall asleep with the television on. 1 With the main menu on the screen, press CH or CH until “Setup” is highlighted.
16 C HAPTER F OUR : VCR O PERA TION Inserting and Ejecting a Video T ape T o insert a video tape: 1 Hold the video tape window- side up, with the arrow pointing away from you. Don’t try to insert a tape upside down or backwards. Use only video tapes labeled “VHS.
C HAPTER F OUR : VCR OPERA TION 17 VCR O PERA TION Playing a Video T ape, continued Using Picture Search Picture Search lets you quickly search a pre-recorded video tape for a particular scene. 1 While playing a tape, press and release FF or REW . The images from the tape are displayed on the screen at a high speed.
18 C HAPTER F OUR : VCR OPERA TION Playing a Video T ape, continued The letter “M” appears beside the time counter . If you want to remove the time counter memory from the screen and cancel the memory stop feature, just press DISPLA Y again. T o return to the scene you marked: 1 Press STOP .
19 C HAPTER F OUR : VCR OPERA TION Recording TV Programs as Y ou Watch, continued Editing While Recording Y ou can edit while recording, selecting only those scenes you want to record from the current television program. This is especially helpful if you want to record a program without commercials.
VCR O PERA TION 20 C HAPTER F OUR : VCR O PERA TION Using Advanced Recording Features, continued The T imer Record menu appears on the screen. 3 Use the CH or CH buttons to select One T ime Program, Daily Program, or W eekly Program. Press VOL+. The type of programming you choose will be displayed in the first line of the on-screen display .
21 C HAPTER F OUR : VCR O PERA TION VCR O PERA TION Using Advanced Recording Features, continued The ending minute will blink. Use CH or CH to select the minute to end recording. Press VOL+ to lock in the minute. Press CH to highlight “Start Date.” ✔ The TV/VCR automatically selects AM or PM for the ending time.
VCR O PERA TION 22 C HAPTER F OUR : VCR O PERA TION Using Advanced Recording Features, continued Using Program Review Program Review allows you to review all of the programmed recordings currently stored in the TV/VCR’ s memory and to remove a programmed recording quickly and easily .
23 C HAPTER F IVE : S PECIAL F EA TURES Viewing the Demonstration Mode The Demonstration Mode displays all on-screen menus and programmable features. 1 With the main menu on the screen, press CH until “VCR Setup” is highlighted. 2 Press VOL+. The VCR Setup screen is displayed.
24 C HAPTER F IVE : S PECIAL F EA TURES Using Block Repeat Block Repeat allows you to repeat a section of tape that you select. Y ou can repeat this section of tape (the “block”) from one to ten times, or endlessly . “Repeat” section should be set up at a minimum ten-second interval.
C HAPTER F IVE : S PECIAL F EA TURES 25 S PECIAL F EA TURES Viewing Closed Captions, continued ✔ In text mode, information unrelated to the captions is displayed, such as news or weather . T ext often covers a large portion of the screen. 4 If you wish, use CH , CH , or VOL+ to change the channel or field.
Using the V-Chip, continued How to Enable/Disable the V-Chip 1 Press the MENU button on the remote control. 2 Press CH button 6 times, so that “V-Chip” is highlighted. (When V-Chip is highlighted, the letters change to red.) 3 Press the VOL + button.
27 C HAPTER F IVE : S PECIAL F EA TURES Using the V-Chip, continued While the “U” or ”B” is blinking, press the CH or CH button to block or unblock the category . Press MENU once to save the TV guidelines. A TV- Rating will be highlighted (RED), and no letters will blink.
28 C HAPTER F IVE : S PECIAL F EA TURES Using the V-Chip, continued 4 The “V-chip mode” screen will appear . Press the CH button, and highlight the field for “MP AA rating” and “to begin.” 5 While “MP AA rating” is highlighted, press the VOL + button.
29 C HAPTER F IVE : S PECIAL F EA TURES Copying, or Dubbing, a Video T o make a copy, or “dub,” of another video tape, you need: • your TV/VCR • a separate VCR (or camcorder) • two A/V cables with connectors. (Y ou can find these at most electronics supply stores.
30 C HAPTER F IVE : S PECIAL F EA TURES Identifying TV Problems Poor picture, no picture, blurred picture, or blue screen. • T ry another channel. Make sure the unit is plugged into a working wall outlet. • Adjust the antenna. • Press LINE IN. • Check all wire connections.
31 C HAPTER S IX : T ROUBLESHOOTING Caring for Y our TV/VCR Please follow these guidelines to get the maximum performance from your TV/VCR. Placement • Do not place the TV/VCR near extremely hot, cold, humid or dusty places. • Do not place the TV/VCR near appliances with electric motors that create magnetic fields, such as vacuum cleaners.
32 A PPENDIX Specifications Format VHS Standard Recording system Rotary , azimuth two-head helical scanning system Luminance: FM azimuth recording Color signal: Converted subcarrier phase shift recording T elevision system NTSC-type color signal EIA Standard (525 lines, 60 fields) Audio track One track T ape width 12.
33 A PPENDIX Curtis Mathes T ronics Color T elevision This CurtisMathes T ronics brand product, as supplied and distributed by CurtisMathes and delivered new, in the original carton to the original co.
34 MEMO AA68-00951A/eng 10/26/00 8:52 AM Page 34.
35 MEMO AA68-00951A/eng 10/26/00 8:52 AM Page 35.
AA68-00951A(ENG) AA68-00951A/eng 10/26/00 8:52 AM Page 36.
デバイスCurtis Mathes CMC13003の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Curtis Mathes CMC13003をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCurtis Mathes CMC13003の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Curtis Mathes CMC13003の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Curtis Mathes CMC13003で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Curtis Mathes CMC13003を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCurtis Mathes CMC13003の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Curtis Mathes CMC13003に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCurtis Mathes CMC13003デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。