D-Linkメーカーdwl-650の使用説明書/サービス説明書
ページ先へ移動 of 60
D-Link Air Plus DWL-650+ 2.4 GHz Wireless Cardbus Adapter Manual Building Netw orks for People.
2 Contents 1. Package Contents ....................................................... 3 2. Introduction .................................................................. 4 3. Wireless Basics ..........................................................
3 1. P ac kage Contents Contents of Package: • D-Link Air Plus DWL-650+ 2.4GHz Wireless Cardbus Adapter • Manual, QIG, and Drivers on CD • Printed Quick Installation Guide If any of the above items are missing, please contact your reseller.
4 2. Intr oduction The D-Link Air Plus DWL-650+ Wireless Cardbus Adapter is an enhanced 802.11b high-performance, wireless adapter that supports high-speed wireless networking at home, at work or in public places.
5 Features and Benefits • Supports 802.1x authentication security • Now even faster performance with the new 4x feature, when used with 4x -enabled DI-614+ or 4x -enabled DWL-900AP+ • Speeds up to 2x faster, with data transfer rates up to 22Mbps, when used with other D-Link Air Plus products • Operates in the 2.
6 3. W ir eless Basics D-Link Air Plus wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or wherever a wireless net work is available.
7 Wireless Basics Network Expansion - Wireless technology allows the network to go where wires cannot go. Reduced Cost-of-Ownership - While the initial investment required for Wireless LAN hardware might be higher than the cost of wired LAN hardware, overall installation expens es and life-cycle costs will be significantly lower.
8 Installation Considerations Designed to go up to 1,312 feet (400 meters) outdoors and up to 328 feet (100 meters) indoors, the D-Link Air Plus DWL-650+ lets you access your network with your laptop computer fr om virtually anywhere.
9 Wireless Basics For the average home, signal range should not be an issue. If you experience low or no signal strength in areas of your home that you wish to access, consider positioning the Access Po int in a location directly between the computers with wireless adapters.
10 Getting Started Setting Up an Infrastructure Network Please remember that D-Link Air Plus wireless devices are pre-configured to connect together, right out of the box, with the default settings. If you are using the 802.1x protocol in your network, your setup may be different than that pictured above.
11 Getting Started Setting up a Wireless Ad Hoc Network IP Address Install the D-Link Air Plus DWL-520+ wireless network adapter into the desktop computer. See the Quick Installation Guide included with the product for installation instructions . Install the DWL-650+ into a laptop computer.
12 5. Installing the D WL-650+ Installing the DWL-650+ Drivers & Utility NOTE: Do not insert the DWL-650+ Cardbus into the Cardbus slot at this point. You will be instructed in Section 2 to install the DWL-650+ Cardbus adapter. Windows XP, 2000, Me, or 98 Installation: The following screen shots are taken from Windows XP .
13 Installing the DWL-650+ Drivers and Utility If the AutoRun function on your laptop computer does not automatically start, proceed to the steps below. If it does, proceed to Section 2. • Go to Start > Run > type D:Setup.exe • Click OK NOTE: The letter “D” represents the letter of the CD-ROM drive.
14 Installing the DWL-650+ Drivers and Utility • Select No, I will restart my computer later. • Click Finish • Shut down your laptop computer. • Insert the DWL-650+ into the Cardbus slot. • Restart your laptop computer • Click Nex t at the Welcome screen (Fig.
15 Installing the DWL-650+ For Windows 2000 , Fig. 5.2.6 may appear after the laptop computer restarts. Select Yes to finalize the installation. For Windows Me and 98 , after the laptop computer restarts, it will ask you to reboot the computer once more to finalize the driver installation.
16 Configuration Utility Link Info After clicking on the Confi guration Utility icon, the Link Info screen will display the following: Status: Displays the MAC Address of the Acce ss P oint that is associated with the DWL-650+. SSID: The Service Set Identifier is the name assigned to the wireless network.
17 Configuration Utility Configuration SSID - (Service Set Identifier) is a nam e that identifies a wireless network. Access Points and wirele ss clients attempting to co nnect to a specific WLAN (W ireless Local Area Network) must use the same SSID. The default setting is default .
18 Configuration Utility Encryption Please note that all devices must share the same Encryption settings to communicate on the network. Data Encryption – enable Encryption by clicking on the box. The DWL- 650+ has Encryption disabled as the default setting.
19 Configuration Utility Site Survey Available Networks The top section of the window displays the Available Networks. Scroll up and down the list and highlight the network to which you wish to connect.
20 Configuration Utility Properties In this window you can configure all the prope rties of a profile in order to connect with a network of your choice. After you have entered your c hanges in this window, click OK t o s a v e t h e changes. Current Setting Current Setting/Default Setting default Fig.
21 Configuration Utility About The ABOUT screen gives you information about the F irmware an d Utility Versions of the DWL-650+. Fig. 6.8 D-Link Air Plus Configuration Utility D-Link Air Plus DWL-650+ 2.
22 7. T r oubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DWL-650+ Wireless Adapter. Read the following descriptions if you are having problem s. (The exampl es bel ow are illustrated in Windows XP.
23 Troubleshooting • Double-click on Network Adapters • Right-click on D-Link Air Plus DWL-650+ Wireless Adapter • Select Properties to check that the drivers are installed properly. • Look under Device Status to check that the device is working properly.
24 Troubleshooting 2. I cannot connect to the access point or the wireless router. • Make sure that the SSID on the DWL-650+ Cardbus adapter is exactly the same as the SSID on the Access Point or wireless router. • Move the DWL-650+ and Access Point or Wireless router into the same room and then test the wireless connection.
25 C. Search for the files TIACXLN.INF and TIACXLN.SYS . Remove these files from the INF and SYSTE M32 (DRIVERS) folders in the Windows directory. Note: Windows XP and Windows 2000 will rename .inf files that have not received WHQL certification into oem.
26 that the key selected is set to the same key as other devices on the network. 7. How can I troubleshoot distance issues using the DWL-650+. • Move the DWL-650+ and Access Point or Wireless router into the same room and then test the wireless connection.
27 Networking Basics Using the Network Setup Wizard in Windows XP Please follow all the instructions in this window: Click Next In the following window, select the best description of your computer. If your computer connects to the Internet through a gateway/router, select the second option as shown.
28 Networking Basics Enter a Computer description and a Computer name. Click Next Enter a Workgroup name. All computers on your network should have the same Workgroup name.
29 Networking Basics Please wait while the wizard applies the changes. When the changes are complete, click Next . Please wait while the wizard configures the computer.
30 Networking Basics In the window below, select the best option. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next . Insert a disk into the Floppy Disk Drive, in this case drive A: Format the disk if you wish, and click Next.
31 Networking Basics Please wait while the wizard copies the files. Please read the information under Here’s how in the screen below. After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network.
32 Networking Basics Please read the information on this screen, then click Finish to complete the Network Setup Wizard . The new settings will take effect when you restart the computer. Click Yes to restart the computer. You have completed configuring this computer.
33 Networking Basics Naming your Computer To name your computer, please follow these directions: In Windows XP : • Click Start (in the lower left corner of the screen) • Right-click on My Computer • Select Properties and click • Select the Computer Name Tab in the System Properties window.
34 Networking Basics Naming your Computer Checking the IP Address in Windows XP/2000 Go to Start > All Programs > Accessories > Command Prompt • In this window, enter the Computer name . • Select Workgroup and enter the name of the Workgroup .
35 Networking Basics Checking the IP Address in Windows XP/2000 Type Command Type ipconfig /all at the prompt . All the configuration settings are displayed as shown below. Type ipconfig /renew at the prompt to get a new IP Address, shown below. ( Windows 98/ME users: go to Start > Run .
36 Networking Basics Assigning a Static IP Address in Windows XP/2000 Note: Residential Gateways/Broadband Routers will automatically assign IP Addresses to the computers on the network, using DHCP (Dynamic Host Configuration Protocol) technology . If you are using a DHCP-capable Gateway/Router you will not need to assign Static IP Addresses.
37 Networking Basics Assigning a Static IP Address (continued) • Right-click on Local Area Connections. • Click Properties • Highlight Internet Protocol (TCP/IP) • Click Properties D-Link AirPlus DWL-650+ Wireless Adapt er Fig.
38 Networking Basics Assigning a Static IP Address (continued) • Select Use the following IP address in the Internet Protocol (TCP/IP) Properties window. • Inpu t your IP address and subnet mask. (The IP Addresses on your network must be within the same range.
39 Checking the Wireless Connection by Pinging For Windows XP and 2000: Go to Start > Run > type cmd . A window similar to Fig. 8.35 will appear. Type ping xxx.xxx.xxx.xxx , where xxx is the IP address of the Wireless Router or Access Point. A good wireless connection will show four replies from the wireless router or access point, as shown.
40 Adding and Sharing Printers in Windows XP After you have run the Network Setup Wizard on all the computers in your network (please see the Network Setup Wizard section at the beginning of Networking Basics ,) you can use the Add Printer Wizard to add or share a printer on your network.
41 Networking Basics Adding a local printer (A printer connected directly to a computer) A printer that is not shared on the network and is connected directly to one computer is called a local printer . If you do not need to share your printer on a network, follow these directions to add the printer to one computer.
42 Networking Basics Adding a local printer • Click Next • Select Local printer attached to this computer • (Deselect Automaticall y detect and install my Plug and Play printer if it has been selected.
43 Networking Basics Adding a local printer • Select and highlight the correct driver for your printer. • Click Next (If the correct driver is no t displayed, insert the CD o r floppy disk that came with you r p rinter and click Have Disk .) • A t this screen, you can change the name of the printer (optional.
44 Networking Basics Adding a local printer Click Finish Click OK This screen g ives y ou information about y our p rinter. When the test page has printed, Fig.
45 Networking Basics Adding a local printer Setting up a Network Printer After you have run the Network Setup Wizard on all the computers on your network, you can run the Add Printer Wizard on all the computers on your network.
46 Networking Basics Setting up a network printer • Click on Add a Printer • Click Next • Select Network Printer • Click Next Fig. 8.40 Fig. 8.
47 Networking Basics Setting up a network printer • Select the printer you would like to share. • Click Next • Click Finish Fig. 8.43 Fig. 8.44 Fig.
48 Networking Basics Setting up a network printer To check for proper installation: • Go to Start > Printers and Faxes The printer icon will appear at right, indicating proper installation.
49 Networking Basics Setting up an LPR printer To share an LPR printer (using a print server,) you will need a Print Server such as the DP-101P+. Please make sure that you have run the Network Setup Wizard on all the computers on your network.
50 Networking Basics Setting up an LPR printer • Select Create a new port • From the pull-down menu, select Standard TCP/IP Port , as shown. • Click Next • Please read the instructions on this screen. • Click Next • Enter the Printer IP Address and the Port Name , as shown.
51 Networking Basics Setting up an LPR printer • In this screen, select Custom. • Click Settings • Enter the Port Name and the Printer Name or IP Address . • Select LPR • Enter a Queue Name. If there is more than one port on the print server, you must name the Queue .
52 Networking Basics Setting up an LPR printer • This screen will show you information about your printer. • Click Finish • Select the printer you are adding from the list of Printers . • Insert the printer driver disk that came with your printer.
53 Networking Basics Setting up an LPR printer • You can rename your printer if you choose. It is optional. Please remember the na me o f your printer. You will need this information when you use the A dd Printer Wizard on the other computers on you r network.
54 Networking Basics Other Tasks For help with other tasks in home or small office networking, see Using the Shared Documents folder and Sharing files and folders in the Help and Support Center in Microsoft Windows XP. 9. T echnical Specifica tions Standards: • IEEE 802.
55 • Outdoors – up to 1,312 feet (400 meters) Diagnostic LED: • Power – solid green light indicates power connection • Link/Activity – green solid/blinking light indicates Link/Activity Power Specifications: • Operating Voltage: 3.
56 • CE Safety: UL 10. Contacting T echnical Suppor t You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product.
57 11. Limited W a r r anty Subject to the terms and conditions set forth he rein, D- Link Systems, Inc. (“D-Link”) provides this L imited warranty for its product only to the person or ent ity th.
58 • The original product owner must obtain a Return Material Authori zation (“RMA”) number from the Authorized D-Link Service Office and, if reques ted, provide written proof of purchase of the product (such as a copy of the dated purchase inv oic e for the product) before the w arranty service is provided.
59 Trademarks: D-Link is a registered trademark of D-Link Sy stems, Inc. Other trademarks or registered trademarks are the property of their re spective manufacturers or owners.
Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights..
デバイスD-Link dwl-650の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
D-Link dwl-650をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはD-Link dwl-650の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。D-Link dwl-650の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。D-Link dwl-650で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
D-Link dwl-650を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はD-Link dwl-650の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、D-Link dwl-650に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちD-Link dwl-650デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
