DaewooメーカーKOR-63F79Sの使用説明書/サービス説明書
ページ先へ移動 of 24
Ser vice Manual Micr owave Oven Model: KOR-63D79S KOR-63D70S KOR-63F79S KOR-63F70S DAEWOO ELECTRONICS CO., L TD. S/M No. : R63D79S002 ✔ Caution : In this Manual, some parts can be changed for improving, their performance without notice in the parts list.
1 PRECA UTIONS T O BE OBSER VED BEFORE AND DURING SER VICING T O A V OID POSSIBLE EXPOSURE T O EXCESSIVE MICR O W A VE ENERGY (a) Do not operate or allow the oven to be operated with the door open.
2 SAFETY AND PRECA UTIONS 1. FOR SAFE OPERA TION Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may cause serious bodily injury to the operator. IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE.
3 MODEL KOR-63D79S KOR-63D70S POWER SUPPLY 230V~50Hz, SINGLE PHASE WITH GROUNDING POWER MICROWAVE 1000W 1,200W CONSUMPTION GRILL COMBINATION MICROWAVE ENERGY OUTPUT 700W 800W MICROWAVE FREQUENCY 2450MHz OUTSIDE DIMENSIONS (W x H x D) 465 x 279 x 364 mm (18.
4 EXTERNAL VIEW 1. OUTER DIMENSION 2. FEA TURE DIA GRAM 1. SAFETY INTERLOCK SYSTEM 2. DOORVIEWING SCREEN Allos viewing of food. The screen is designed so that light can pass through, but not the microwave. 3. DOOR HOOK When the door is closed, it will automatically lock shut.
5 INST ALLA TION 1. Steady , flat location. This microwave oven should be set on a steady, flat surface. 2. Leave space behind and side. All air vents should be kept a clearance. If all vents are covered during operation, the oven may be overheated and, eventually, cause oven failure.
1. Connect the main lead to an electrical outlet. 2. After placing the food in a suitable container, open the oven door and put it on the glass tray. The glass tray must always be in place during cooking. 3. Close the door securely. 4. Choose cooking power level by setting V.
7 DISASSEMBL Y AND ASSEMBL Y Cautions to be observed when trouble shooting. Unlike many other appliances, the microwave oven is high-voltage, high-current equipment. It is completely safe during normal operation. However, carelessness in servicing the oven can result in an electric shock or possible danger from a short circuit.
8 1. T o remove cabinet 1) Remove three screws on cabinet back. 2) Push the cabinet backward. 2. T o remove door assembl y 1) Remove two screws which secure the stopper hinge top. 2) Remove the door assembly from top plate of cavity. 3) Reverse the above for reassembly.
9 4. Method to reduce the gap between the door seal and the oven fr ont surface. (1) To reduce gap located on part ‘ A ’ Loosen a screws on stopper hinge top, and then push the door to contact the door seal to oven front surface. Tighten two screws.
10 5. T o remove contr ol panel parts. 1) Remove the screw which secure the control panel, push up two snap fits and draw forward the control panel assembly. 2) Remove the door open lever from the control panel. 3) Remove four screws which secure the timer assembly.
11 6. T o remove high v oltage capacitor . 1) Remove a screw which secure the grounding ring terminal of the H.V. diode and the capacitor holder. 2) Remove the H.V. diode from the capacitor holder. 3) Reverse the above steps for reassembly. ◆ High v oltage circuit wiring 7.
12 NOTE : Never install the magnetron without the metallic gasket plate which is packed with each magnetron to pre - vent microwave leakage. Whenever repair work is carried out on magnetron, check the microwave leakage. It shall not exceed 4mW/cm 2 for a fully assembled oven with door normally closed.
13 INTERLOCK MECHANISM AND ADJUSTMENT The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave.
14 TR OUBLE SHOO TING GUIDE (TROUBLE 1) Door shut, timer set, but no cooking takes place. Following the pr ocedure belo w to chec k if the o ven is def ective or not. 1. Check grounding before trouble checking. 2. Be careful of the high voltage circuit.
15 Does the oven lamp light? Does the turntable turn? YES YES Continuity Does the fan motor work when you shut the door and turn the timer? Check the isolation of filament winding of high voltage transformer. Replace high voltage transformer. NO Continuity Replace magnetron Good Replace or repair oven lamp, turntable motor.
16 MEASUREMENT AND TEST 1. MEASUREMENT OF THE MICRO W A VE PO WER OUTPUT Microwave output power can be checked by indirectly measuring the temperature rise of a certain amount of water exposed to the microwave as directed below.
17 2. MICRO W A VE RADIA TION TEST PROCEDURES 1 . Prepare Microwave Energy Survey Meter, 600cc glass beaker, and glass thermometer 100 ˚ C(212 ˚ F). 2. Pour 275cc±15cc of tap water initially at 20 ±5 ˚ C(68±9 ˚ F) in the 600cc glass beaker with an inside diameter of approx.
18 3. COMPONENT TEST PROCEDURE • High voltage is present at the high voltage terminal of the high voltage transformer during any cooking cycle. • It is neither necessary nor advisable to attempt measurement of the high voltage.
19 WIRING DIA GRAM.
20 EXPLODED VIEW AND P AR TS LIST 1. DOOR ASSEMBL Y Ref er to Disassembly and assemb ly . 2. CONTROL P ANEL ASSEMBL Y Ref er to Disassembly and assemb ly .
21 NO PART CODE PART NAME DESCRIPTION Q'TY A00 3511714420 DOOR AS KOR-63D59A 1 3511714450 DOOR AS KOR-63F59A 1 B00 3516720620 CONTROL-PANEL AS KOR-63D79S 1 3516720630 CONTROL-PANEL AS KOR-63F79S 1 F01 3510805000 CABINET SECC T0.
22 NO PART CODE PART NAME DESCRIPTION Q'TY F23 3518701100 FUSE HV 5KV 0.55A HV-41A55-02 1 F24 3518113751 TRANS HV TM-N70S0-63T(KOR-63D79S/63F79S) 1 3518113701 TRANS HV DY-N80S0-63T(KOR-63D70S/63F70S) 1 F25 3516003700 SPECIAL SCREW TT3 HEX 4X8 FLG MFZN 4 F26 3510311700 BASE SBHG T0.
S/M NO . : R63D79S002 D AEW OO ELECTRONICS CO ., L TD . 686, AHYEON-DONG MAPO-GU SEOUL, KOREA C.P.O. BOX 8003 SEOUL, KOREA TELEX: DWELEC K28177-8 CABLE: “DAEWOOELEC” PRINTED D A TE: J un.
デバイスDaewoo KOR-63F79Sの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Daewoo KOR-63F79Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDaewoo KOR-63F79Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Daewoo KOR-63F79Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Daewoo KOR-63F79Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Daewoo KOR-63F79Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDaewoo KOR-63F79Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Daewoo KOR-63F79Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDaewoo KOR-63F79Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。