Datalogic ScanningメーカーDS2200の使用説明書/サービス説明書
ページ先へ移動 of 41
DS2200 Reference Manual.
.
DS2200 REFERENCE MANUAL.
DATALOGIC S.p.A. Via Candini 2 40012 - Lippo di Calder ara di Reno Bologna - Italy DS2200 Reference Manual Ed.: 4/2006 ALL RIGHTS RESERVED Datalogic reserves the right to make modifi cati ons and im provements without prior notification .
CONTENTS REFERENCES ............................................................................................. v Conventio ns .................................................................................................. v Reference Docu mentation .
4 MAINTENANCE ......................................................................................... 21 4.1 Cleanin g ...................................................................................................... 21 5 TECHNICAL FE ATURES ..
REFERENCES CONVENTIONS This manual uses the following conventio ns: “User” or “Operator” refers to anyone using a DS2100A. “Device” refers to the DS2100A. “You” refers to the System Admin istrator or Technical Support pers on using this manual to install, mount, operate, maintain or troublesho ot a DS2100A.
SAFETY PRECAUTIONS LASER SAFETY The following information i s provided to comply with the rules imposed by international authorities and refers to the correct use of the DS2200 scann er. Standard Regulations This scanner utilizes a lo w-power laser diode .
The warning label in dicating exposure to laser li ght and the device classification is applied onto the body of the s canner (Figure A, 8): CAUTION-CLASS 3B LASER LI GHT WHEN OPEN A VO ID E XPOSU RE TO B EA M This product conforms to the ap plicable requi rem ents of 21 CFR1040 at the date o f manufacture.
POWER SUPPLY - This product is intended to be installed b y Qualified Pers onnel only. - DS2200 All Models: This device is intended to be supplied either by a UL Li sted NEC Class 2 power source, or a UL l isted ITE Limited Po wer Source (LPS), rated 5Vdc, minimum 0.
GENERAL VIEW DS2200 1 6 5 4 7 3 2 8 Figure A 1 2 3 4 5 6 7 8 Barcode Im age Input Window Laser Beam Output Window Pow er On LED Good Read LED Ext Tr ig LED TX D ata LED Laser Warni ng and Device Class.
GUIDE TO INSTALLATION The follo wing can be use d as a checklist to v erify all the n ecessary steps f or complete installation of the DS2200 scanner. 1. Read all information in the s ection "Saf ety Precautions” at the beginning of this manual.
INTRODUCTION 1 1 INTRODUCTION 1.1 PRODUCT DESCRIPTION The DS2200 scann er is a cost effective barcode r eader complete with decode r designed to satisf y demanding requirements associated with high performance scanning.
DS2200 1 A security system allo ws the laser to activate onl y once the motor has reached the correct rotational speed; conseque ntly, the laser beam is generated after a slight delay from the power on of the scanner.
INTRODUCTION 1 The following models are therefore ava ilable: DS2200 - X X X X Optica l Resolution 1 = Sta ndard Resolution 2 = High Resolution Readin g Wi ndow Position 0 = Direct Optic Vers ion 0 = Linear 1 = Rast er Co mmunic at io n Interf a ce 1 = RS2 32 + RS 485 The following tables displa y each version’s reading perform ance.
DS2200 2 2 INSTALLATION 2.1 PACKAGE CONTENTS Verify that the DS2200 reader and all the parts supplied with the equipm ent are present and intact when opening the pa ckag ing; the list of parts includes: • DS2200 reader with cabl e • Installation Manual • Bar code test chart (PCS = 0.
INSTALLATION 2 2.2 MECHANICAL INSTALLATION DS2200 can be installed to operate i n any position. There are three scre w holes (M2.5 x 5) on the body of the reader for mounting. T he diagram below gives all th e in formation requ ired for instal lation; refer to par.
DS2200 2 2.2.1 Mounting DS2200 Using the DS2200 mounting bracket you can obtain the most suitable po sition for the reader as shown in the figure belo w: Pitch Skew 6.
INSTALLATION 2 2.3 ELECTRICAL CONNECTIONS The DS2200 cabl e is equipped with a 25-pin female D-s ub connector for conn ection with the power supply and input/output signal s: CA UTI ON Do not connect GND and SGND to d ifferent (external) ground references.
DS2200 2 2.3.1 Power Supply The following pins of the DS2200 conn ector are used: 13/9 25 1 VS GND CHASSIS USER INTE RFA CE GND V+ (5 Vdc) DS2200 Figure 4 - Power suppl y connections The power must be 5 Vdc only.
INSTALLATION 2 The following figure s hows an example o f a multidrop configuration bet ween a Multiplexer and DS2200 scan ners. 120 Ohm max. 1200 m. RTX485 + RTX485 - Three wires + shi eld MULTIPLEXER # 1 DS2200 RTX485+ RTX485 - SGND # 0 DS2200 DS2200 # x (up to 31) 120 Ohm max.
DS2200 2 7 SGND SGND TXD RXAUX 3 RXD TXAUX 2 USER INTERFACE DS2200 Figure 7 - RS232 auxiliar y interface connection s 2.3.4 Inputs The inputs available on the connector supp lied w ith the scanner are.
INSTALLATION 2 2.3.5 Outputs Two general p urpose outputs are av ailable. T hese outputs can only be connected as open collector configuratio ns. The following pins are present on the conn ector of th.
DS2200 2 The Pitch angle is represent ed by the value P in Figure 10. Position the reader in order to minimize the Pitch angle. P Figure 10 - Pitch Angle The Skew angle is represented by the value S in Fig ur e 1 1. Position the reader to assure about 15° for the Skew angle.
INSTALLATION 2 2.5 TYPICAL LAYOUTS The following typical layouts refer to system hardware configurations . Dotted lines in the figures refer to optional hard ware configurations within the partic ular layout. These layouts also r equire the correct setup of the soft ware configuration parameters.
DS2200 2 The Master scanner is also conn ected to the Host on the RS232 auxiliar y serial interface. The External Trigger signal is unique to the system; there is a single reading p hase and a single message from the Master scanner to the Host computer.
INSTALLATION 2 2.5.3 Multiplexer Each scanner is connecte d to a Multiplexer (for e xample MX4000) with the RS485 half-duplex main interface. 1 2 3 RS485 Main Interface Auxiliary Interface (Local Echo.
DS2200 3 3 READING FEATURES The number of scans performed on the c ode by the D S2200 and therefore th e decoding capabilit y is influenced by the following parameters: • number of scans per second .
READING FEATURES 3 For example, the DS2200 (500 sca ns/sec.) for a 25 mm high code moving at 50 0 mm/s performs: [(25/500) * 500] - 2 = 23 effective scans.
DS2200 3 3.3 PERFORMANCE The DS2200 scann er is available i n different versions accord ing to the readin g performance. Version Max Code Resol ution Speed mm (mils) scans/s 1XXX 0.15 (6) 500 2XXX 0.07 (3) 500 Version Reading Distance 1XXX 50 mm (2.0 in) - 220 mm (8.
READING FEATURES 3 3.4 READING DIAGRAMS The following diagrams s how the reading distance for barco des with different densities. DS2200-1XXX (Standard Resolution) 2 1 0 1 5 4 3 2 3 4 5 (in) 01 3 21 6 (in) 45 7 8 9 02 0 4 0 6 0 80 100 120 140 160 180 200 220 240 260 (mm ) 120 100 80 60 40 20 0 20 40 60 80 100 120 (mm ) 0 ≥ 0.
DS2200 3 DS2200-2XXX (High Resolution) 1 0 2 1 2 (in) 01 5 3 (in) 24 0 10 20 30 40 50 60 70 80 90 100 110 120 130 (m m) 60 50 40 30 20 10 0 10 20 30 40 50 60 (mm ) 0.10 m m (4 mils) 0.12 mm (5 mils) 0.15 mm (6 mils) ≥ 0.20 mm (8 mi ls) NOTE: (0,0) is the center of th e la ser beam output w indow.
MAINTENANCE 4 4 MAINTENANCE 4.1 CLEANING Clean the windows periodical ly for cont inued correct operation of the reader. Dust, dirt, etc. on the windows ma y alter the reading perfor mance. Repeat the operation frequentl y in particularly dirty environ ments.
DS2200 5 5 TECHNICAL FEATURES DS2200-1XXX DS2200-2XXX ELECTRICAL FEATURES Power Maximum input voltage 5 Vdc ± 5% Power consumption max. 2 W Serial Interfaces Main RS485 Half-Duplex Auxiliary RS232 Baud Rates 150 to 115200 Inputs External Trigger Outputs User-defined OUT1 and OUT2 V CE max.
TECHNICAL FEATURES 5 SOFTWARE FEATURES READABLE CODE SYMBOLOGIES • EAN/UPC (including Add-on 2 and Add-on 5) • Code 93 • 2/5 Interleaved • Code 128 • Code 39 (Standard and Full ASCII) • EA.
GLOSSARY Ape rt ur e Term used on the required CDRH warning labels to describe the laser exit windo w. Barcode A pattern of variable- width bars and spaces which represents numeric or alphanumeric data i n machine-readable fo rm.
EEPROM Electrically Erasable Progra mmable Read-Only Memory. An on-board non-volati le memory chip. Full Duplex Simultaneous, two-way, indep endent transmission in both directions. Half Duplex Transmission in either directi on, but not sim ultaneously.
Protocol A formal set of conventions governing th e formatting and relative timing of message exchange bet ween two communicating systems. Raster The process of projecting the laser be am at varied angles spaced evenl y from each other. Typically, the mirrore d rotor surfaces are angle d to create multiple scan lines instead of a single beam.
Symbol A combination of characters inclu ding start/stop and checksum characters, as required, that form a complete scannable barcode. Tilt Rotation around the Z ax is. Used to describe the positi on of the barcode with respect to the laser scan line.
INDEX A Accessories; 3 C Cleaning; 21 E Electrical Connections; 7 G General View; ix Glossary; 24 Guide to Installation; x I Inputs; 10 Installation; 4 Interfaces Auxiliary – RS232; 9 Main – RS485.
DATA LOGIC S.p.A ., Via Candini, 2 40012 - Lippo di Calderara Bologna - Italy 05 dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el DS2200-XXXX Laser Scanner e .
デバイスDatalogic Scanning DS2200の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Datalogic Scanning DS2200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDatalogic Scanning DS2200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Datalogic Scanning DS2200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Datalogic Scanning DS2200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Datalogic Scanning DS2200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDatalogic Scanning DS2200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Datalogic Scanning DS2200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDatalogic Scanning DS2200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
