DavolinkメーカーDVP-200の使用説明書/サービス説明書
ページ先へ移動 of 53
DVP-100/200 IP P ho ne USER GUIDE.
DAVOLINK DVP-1 00/200 Conventi ons For product safety and correct operation, the following informa tion must be g i v e n t o t h e o p e r a t o r / u s e r a n d s h a l l b e r e a d b e f o r e t h e i n s t a l l ation and operation.
Installation guide This p age intentionally lef t 4 / 54.
DAVOLINK DVP-1 00/200 Table of Contents 1 DVP-100/200 OVER VIEW ................................................................................ 7 1.1.CONT AIN ...........................................................................................
Installation guide This p age intentionally lef t 6 / 54.
DAVOLINK DVP-1 00/200 1 DVP-100/200 Overview 1.1. Contai n z D V P V o I P P h o n e 1 e a z External power adapter 1ea z LAN Cable (RJ-45) 1ea z H a n d s e t 1 e a z H a n d s e t c o d e 1 e a z H e a d s e t ( o p t i o n a l ) 1 e a z U s e r g u i d e 1 e a You should check all belonging in the box.
Installation guide < Figu re 1 : DV P-100 > Button and Feature name of DVP-100/200. No Button and Feature Name Description 1 LCD screen z The to p l i n e d i s p la y s an y of the icons shown below, depending on the current state of the phone.
DAVOLINK DVP-1 00/200 4 ENTER z It applies the changed configuration after set up some function. 5 Left Index ( ) z It moves to the upper directory. 6 Up Index ( ) z It moves to the other directory. z It scrolls upward on the screen. 7 D o w n I n d e x ( ) z It moves to the other directory.
Installation guide 1.4. Description ICON on LCD Screen DVP-100/200 Screen has 3 lines. The below described Icons are a ppeared at the first line. No ICON Description 1 z Show the Internet connectivity (Network) z It will be blinking if the connection is lost.
DAVOLINK DVP-1 00/200 2 Connecting and Installation 2.1. Cabl ing Refer to the locate ports on the rear of the DVP-100/200. It sh ould be connected to the correspondi ng Network or Interface.
Installation guide To access configuration mode, push the “PROG” button at the fir st time. 2.2.2 WAN IP Add ress Allo cation 1) DHCP Setting Choose DHCP mode for WAN IP configuration, when DVP-100/200 is connected t o the enabled Auto-Co nnection ADSL modem or Cable mo dem.
DAVOLINK DVP-1 00/200 “2*Manual”, then select “1*IPAddress”. ④ put the IP address. Instruction “ * ” button rep resented “ . ” (dot). If the IP address is not correct, delete using the “ MUTE ” button. ⑤ Netmask and Gateway setting are the same like IP address sett ing.
Installation guide 3) PPPoE Setting If your ADSL modem needs to set PPPoE account on DVP-100/200, choose PPPoE for WAN IP configuration. Instruction Y ou need correct user name and password gets from your ISP . ① Select “3*PPPoE”. ② Select “1*PPPoE User” for PPPoE account.
DAVOLINK DVP-1 00/200 NOTE At the normal case, you don’t ne ed the PPPoE ser vice name. ⑤ Push the “ ” button to save the changed setting. 2.2.3 NAT fun ction and L AN IP conf iguration DVP-100/200 support NAT function for L ocal PC. For NAT function , you need to set up LAN IP address and DHCP function like below.
Installation guide ② Select “1*LANIPAddress” by pushing the “ENTER” or “ ” button to configure LAN IP address. NOTE T he default LAN IP address is 192 .168.1.254 ③ T o e n a b l e D H C P S e r v e r f u n c t i o n , s e l e c t “ 1 * Y e s ” a f t e r s e l e c t i n g “2*DHCP Server”.
DAVOLINK DVP-1 00/200 2.3. VoIP Configuration 2.3.1 H.323 Setup (1) RAS setting DVP-100/200 has to be registered to ITSP (Internet Telephony Se rvice Provider) to use VOIP service.
Installation guide ③ S e l e c t G K I n t e r f a c e m o d e a m o n g “ 1 * G K I n f . M o d e ” , “ 2 * M a n u a l G K Used” and “3*Auto GK Used” after moving to “1*GK Inf. Mode” ④ Select one of GK interface mode and configure its collaborating setup.
DAVOLINK DVP-1 00/200 ⑥ DVP-100/200 sends a registration request message to Gatekeepe r with H.323 ID. Select the “3*H.323-ID” and put correct H.323ID. Instruction You can change the inpu t mode using “ ” or “ ” button. ⑦ DVP-100/200 sends RRQ message periodically t o Gatekeeper base d on below RRQ Timer setting.
Installation guide ⑩ It is the timeout va lue of Q.931 message. NOTE The default Q.931 respo nse ti meout value is 20 secon ds ⑪ DVP-100/200 pays attention to the TTL value supplied by Gatek eeper in t h e R C F m e s s a g e . I f t h e R C F m e s s a g e d o e s n o t i n c l u d e T T L v a l u e , i t follows RAS TTL value.
DAVOLINK DVP-1 00/200 NOTE The default Q.931 call co ntrol port is TCP 1720. This port initiates the Q.931 call c ontrol messages for the pur pose of connecting, maintaining, and di sconnecting calls. ③ Choose “2*Fast Connect” mode whether “1*Yes” or “2*No”.
Installation guide ⑧ DVP-100/200 can handle the received Alert message using ”7*No n- Fast Alert” menu. Discard Alert message if the message doesn’t include audio information. The basic value is “2*NO”. ⑨ Set CanMap Alias function on DVP-100/200 at the ”8*CanMapAlia s” menu.
DAVOLINK DVP-1 00/200 ① G o t o c o n f i g u r a t i o n m o d e u s i n g t h e “ P R O G ” b u t t o n . R e a c h t o t h e “ConfigVoIP” menu like above RAS setting. Enter at “2*ConfigVoI P” to access “3*RTP Config” menu. ② DVP-100/200 can set Frame numbe r at one packet per ordinary i nterval.
Installation guide W e n e e d t h e D o o r b e l l s e r v e r a n d t h e P r o x y s e r v e r t o p r o v i d e t h e V o I P service on a private netwo rk, like the above figure ③ P u s h t h e “ E N T E R ” b u t t o n o r “ ” t o s e t t h e D o o r B e l l I P a d d r e s s .
DAVOLINK DVP-1 00/200 (5) Miscellaneous Setting This menu is optional part. So just leave away this part if you don’t have any more information. ① Go to “5*Miscellaneous” like above P-Server setting. ② Put the VOIP service provider name at the “1*VoIPSrvProvide” menu if it is needed for call.
Installation guide 2.3.2 SIP Setup (1) SIP Proxy Server Setting ① T o s e t u p V o I P s e r v i c e w i t h S I P p r o t o c o l , a c c e s s “ 2 * S e t t i n g s ” followed b y p u s h i n g “ P R O G ” b u t t o n . G o t o “ 2 * C o n f i g V o I P ” t o a c c e s s S I P s e rver setting.
DAVOLINK DVP-1 00/200 ④ P o r t n u m b e r o f t h e S I P p r o x y s e r v e r . T h i s i s t h e p o r t o n w h i c h the S IP client will listen for me ssages.
Installation guide ② Select “1*SIP” or “2*TEL” mode at “1*URLMode”. ③ Set the Caller ID number at “2*DisplayName”. ④ Put the telephone numb er at “3*PhoneNumber”. ⑤ The domain providing service to a SIP user. Set the domain na me at “4*ServiceDomain”.
DAVOLINK DVP-1 00/200 (3) Authentication Setup ① Go to the “2*ConfigVoIP” menu like above URL setup. And selec t “3*Authentication” to put user i nformation for authentication. ② Put the user name for authentication at “1*AuthUserId”. ③ Put the correct user password fo r authentication at “2*AuthPa ssword”.
Installation guide 2.4. Initialization 2.4.1 Restart This chapter explains how to re set the DVP-100/200 at LCD scree n menu. The Phone has to be reset to a pply changed configuration. ① Access to the “6*Reset” menu using “ ” followed by pushing “PROG” button.
DAVOLINK DVP-1 00/200 2.5. Call History This Phone saves called nu mber and caller number. ① Select “3*CallLogs” at the ma i n m e n u t o s e e c a l l h i s t o r y . T h e re are three call history directory; M issed call, Incoming call and Ou tgoing call.
Installation guide 2.6. Phone Book Phonebook saves telephone number with name by index number. DVP - 100/200 can save the list up to 200. ① Get to “4*Phone Book” at the main menu. ② Reach to submenu of Phone book using “ ” button. You can find out a l i s t b y S p e e d o r N a m e o r N u m b e r .
DAVOLINK DVP-1 00/200 2.8. Bell type and Volume control You can select Bell type and volume at “6*Ring/Volume”. Increas e or decreases volume for the hands et, headset or speakerphone. ① Get to “6*Ring/Volume” menu to control Bell type and volume.
Installation guide ⑥ Go to “5*SpeakerVolume” to adjust the speaker volume. ⑦ Go to “6*MicVolume” to adjust the Mic volume. ⑧ Go to “7*HeadsetEarVo1” to a djust the headset ear volume. ⑨ Go to “8*HeadsetMic” to adju st the headset Mic volume.
DAVOLINK DVP-1 00/200 3 WEB Management 3.1 PC Connect ion After installing system properly, you should have to assigne IP address on the connected PC between 192.
Installation guide 2. Click right button of mouse on “L ocal Area Connection”. And the n click on “Properties” button. 3. Select “Internet protocol (TCP/I P)” and click on “Properties” b utton.
DAVOLINK DVP-1 00/200 4. Select “IP address automatically and “DNS address automatically ” in internet protocol attribute window. If you want to get a dynamic IP address from DVP-100/200, Click t h e “obtain an IP address automatically.
Installation guide NOTE Windows XP and 2000 do not need to restart PC for reloading the n e w I P a d d r e s s O t h e r W i n d o w s O S h a v e t o r e s t a r t f o r a c t i v a t i o n t h e changes.
DAVOLINK DVP-1 00/200 3.1.2 Access to Web Man agement server Before accessing Web Manager, verify the state of the DVP-100/2 00 LAN Icon on LCD is appeared properly. 1. Open a new Web browser window and enter the DV-100/200’s IP address of LAN interface (PC port).
Installation guide 3.1.3 Configuration on the WEB L i k e t h e f o l l o w i n g s c r e e n , h a r d w a r e v e r s i o n a n d s o f t w a r e v e r s i o n are displayed. NOTE Build date and time could be dif ferent from each other although the same software version.
DAVOLINK DVP-1 00/200 2. IP Setting Current IP address, IP mode and Hardware address will show up a t this menu like below picture. You can also change all configuration related IP address such as IP address, IP mode. Static IP : If a dedicated IP address is allocated for IP Phone, select the static IP mode for WAN IP.
Installation guide Dynamic IP ( DHCP) : I f t h e I P a l l o c a t i o n m o d e i s d y n a m i c f o r W A N , select DHCP. Then push WAN IP Se tting button to apply configura tion. Dynamic IP (PPPoE) : I f the DVP-100/200 is connected to DSL modem which is not terminate PPPoE co nnection, select ADSL (PPPoE) mo de for WAN IP allocation.
DAVOLINK DVP-1 00/200 3. VOIP Setting To use VOIP Telephony service configures related information su ch as Ga tek eep er a ddr ess , H. 323 ID, Tel num ber and so o n. T he par ame t ers is the same as above LCD setting. But this WEB setting can set up all VOIP setting at one time.
Installation guide H.323 ID : It is a H.3 23 Identification for authen tication. Area code : Local Number. Phone number : E.164 number which is recognized at Gatek eeper. Virtual Calling Number : E . 16 4 i s a n al i as a d dr e s s w i th i n a H .3 2 3 Ne t wo r k to address the dest ination terminal.
DAVOLINK DVP-1 00/200 DoorBell address : I t i s t h e I P a d d r e s s o f D o o r B e l l t o i n f o r m t h e I P address of P-Server to P-Client (DVP-100/200) It supports 3 Dorebell address to give reliability. Voice Packet : Voice Packets can only choose one among three ways like Both Rx/Tx, only Rx or None .
Installation guide 6. DHCP Server Setting DVP-100/200 has DHCP server function for local network. You can p u t the IP pool range using by setting start IP address and maximum C l i e n t number.
DAVOLINK DVP-1 00/200 7. Port Forwarding Port Forwarding allows you to dire ct incoming traffic from W AN side (identified by Protocol and External port) to the Internal server with private IP address on the LAN side.
Installation guide 8. System Status Below picture shows the current LAN and WAN I P address and registration status of VoIP. Network Port I P : I t s h o w s c u r r e n t W A N I P a d d r e s s . N e v e r m i n d e v e n though the net mask is 0.0.
DAVOLINK DVP-1 00/200 check the Line status and I nternet connectivity. 9. Restart The DVP-100/200 will be restart as soon as push the Restart but ton.
Installation guide 10. Upgrade A t t h e b e l o w U p g r a d e m e n u , y o u c a n u p g r a d e s o f t w a r e a n d s e t u p the log server. DVP-100/200 can upgrade new s/w image auto matically and manuall y. Auto upgrade needs the S erver IP address.
DAVOLINK DVP-1 00/200 1) Download the software from FTP server to PC. 2) Open the Dos command. 3) Change the prompt directory to the other directory which has t h e software image. 4) Execute the batch command on the Dos prompt. Example) C:₩ upgrade.
Installation guide This p age intentionally lef t 52 / 54.
DAVOLINK DVP-1 00/200 53 /54.
Installation guide IP Phone D VP-100/200 User Manual © 2005 DAVOLINK Co., Inc. All rights reserved. Information in this document is proprietary to DA V OLINK Co., Inc No information contained here may be copied, translated, transcribed or duplicated by any form without the prior written consent of DA VOLINK.
デバイスDavolink DVP-200の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Davolink DVP-200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDavolink DVP-200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Davolink DVP-200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Davolink DVP-200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Davolink DVP-200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDavolink DVP-200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Davolink DVP-200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDavolink DVP-200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
