DellメーカーD50Dの使用説明書/サービス説明書
ページ先へ移動 of 18
Installation Guide Dell ® Wyse D Class Conversion to WES7 Wyse USB Firmware T ool TM Release 1.20 . 0 .1 Products: D10D , D50D , D90DW Issue: 040914 PN: 883887-38L Rev .
Copyright Notices © 2014 , Dell Inc. All Rights Reserved. This manual and the software and firmware described in it are copyrighted. Y ou may not reproduce, transmit, transcribe, store in a retrieval.
Contents 1 Introduction 1 Kit Contents 1 Kit Warranty 2 Overview 2 Dell T echnical Support 2 Related Documentation and Services 2 Dell Online Community 2 2 Installing D Class Flash 3 Requirements 3 Pr.
iv Contents This page intentionally b lank..
1 Introduction This guide provides step-by-step instructions to use Wyse USB Firmware T ool to convert the following Wyse D class thin clients to WES7: • D10D (with minimum 2 GB RAM) • D50D (with .
2 Chapter 1 Kit Warranty The warranty on the hardware component of this kit assumes the remaining months of warranty of the thin client in which it is installed, or for 90 days, whichever is greater . Installation of this kit will not void the factory warranty, however the user will be responsible for damage due to improper installation.
2 Installing D Class Flash This chapter contains information for users of Wyse D class thin clients who must install new flash. Requirements • Small Phillips screwdriver WARNING : Flash modules may be susceptible to damage by Electro- Static Discharge (ESD).
4 Chapter 2 4. Place your thumbs on the top surface of the opposite end where the three screws were removed. With a continuous motion, push firmly downward and towards the back panel (pushing down unlatches the hooks under the cover). The cover will shift approximate 1/4 inch to hang over the back panel.
Installing D Class Flash 5 Figure 5 Main board and Flash module 7. Remove the existing flash module. Locate the flash module and use the Phillips Screwdriver to remove its retaining scr ew as shown in Figure 6. Lift the flash module out of the socket.
6 Chapter 2 This page intentionally b lank..
3 Installing WES7 Firmware This chapter includes the requirements and procedur es you need to install and use Wyse USB Firmware T ool to update your thin client to WES7 firmware. TIP : The purpose of the USB Firmware T ool is to configure a bootable USB key f or device firmware.
8 Chapter 3 Procedures IMPORT ANT : Complete the following procedures as an administrator (administrator privileges are required). Step 1: Copy the D Class WES7 Conversion Image Folder (on the DVD- RO.
Installing WES7 Firmware 9 Figure 8 Configuration options 3. Select the Configure the USB key to Copy/Pull or to Update/Push firmware option, and then click Next to open the Select the Configuration dialog box. Figure 9 Update firmware options - Windows Embedded Standard 7 4.
10 Chapter 3 Figure 10 Browse for image file 8. Click Browse . Figure 11 Browse to select commandsXml.xml 9. Navigate to the D Class WES7 Conversion Image folder (on your hard drive) that contains the commandsXml.
Installing WES7 Firmware 11 11 . Select the USB key onto which you want the configurations (you can use Refresh as needed to recognize an inserted USB key), and then click Next . The pr ogress bars show the overall (formatting and configuration) progress and task progr ess.
12 Chapter 3 Step 5: V erifying Thin Client Operation After the thin client displays the WES7 desktop, you can verify the V ersion and that your general client information is correct. 1. On the General tab of the Wyse Client Information window ( Start > All Programs > Wyse Client Information ), verify the following: • V ersion is 9.
Installing WES7 Firmware 13 Step 7: Obtain a Firmware Update After converting your thin clients, obtain any available firmware update at http://www. wyse.com/serviceandsupport/support/downloads.asp . WARNING : Use of the Software on more than one device requires that you first purchase from Dell additional copies of, or licenses to, the Softwar e.
Installation Guide Dell ® Wyse D Class Conversion to WES7 Issue: 040914 Written and published by: Dell Inc., April 2014 Created using FrameMaker ® and Acr obat ®.
デバイスDell D50Dの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Dell D50Dをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDell D50Dの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dell D50Dの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dell D50Dで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dell D50Dを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDell D50Dの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dell D50Dに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDell D50Dデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。