DellメーカーD810の使用説明書/サービス説明書
ページ先へ移動 of 51
Dell™Latitude™D810ServiceManual Before You Begin System Components Memory Modules, Mini PCI Card, Modem, and Modules Internal Card With Bluetooth ® Wireless Technology The Coin - Cell.
Back to Contents Page Before You Begin Dell™Latitude™D810ServiceManual Preparing to Work Inside the Computer Recommended Tools Computer Orientation Screw Identification Preparing to Work Inside the Computer 1.
Recommended Tools The procedures in this manual require the following tools: l #1 Phillips screwdriver l ¼ - inch flat - blade screwdriver l Small plastic scribe l Flash BIOS updat.
Microprocessor Fan: (1 each) Keyboard: (2 each) Display Assembly: (2 each) Video Card Fan: (1 each) Display Latch: (2 each) Display Panel Cable: (1 each) Display Panel: (8 each) Speake.
Back to Contents Page Internal card with Bluetooth™wireless technology (1 each) Button Board (2 each) .
Back to Contents Page Flashing the BIOS Dell™Latitude™D810ServiceManual 1. Ensure that the AC adapter is plugged in and that the main battery is installed properly. 2. Insert the flash BIOS update program floppy or CD and turn on the computer.
Back to Contents Page Internal Card With Bluetooth ® Wireless Technology Dell™Latitude™D810ServiceManual If you ordered an internal card with Bluetooth ® wireless technology with your computer, the card is already installed.
Back to Contents Page 1 coin - cell battery 2 screw for card with Bluetooth wireless technology 3 card with Bluetooth wireless technology .
Back to Contents Page Center Control Cover Dell™Latitude™D810ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Turn the computer top - side up and open it. 3. Remove the center control cover: a.
Back to Contents Page Coin - Cell Battery Dell™Latitude™D810ServiceManual A coin - cell battery maintains computer configuration, date, and time information.
13. Close the small access door. 14. Insert the main battery and close the battery door. 15. Connect your computer and devices to electrical outlets, and turn them on. 16. Enter the system setup program and restore the settings you recorded in step1 .
Back to Contents Page Microprocessor Module Dell™Latitude™D810ServiceManual Removing the Microprocessor Module 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the display assembly .
1. Align the pin - 1 corner of the microprocessor module with the pin - 1 corner of the ZIF socket, and insert the microprocessor module. When the microprocessor module is correctly seated, all four corners are aligned at the same height. If one or more corners of the module are higher than the others, the module is not seated correctly.
Back to Contents Page Microprocessor Thermal - Cooling Assembly Dell™Latitude™D810ServiceManual Removing the Microprocessor Thermal - Cooling Assembly 1. Follow the instructions in " Preparing to Work Inside the Computer .
Installing the Microprocessor Thermal - Cooling Assembly 1. Place the microprocessor thermal - cooling assembly directly down onto the system board. Push straight down. 2. Tighten the four captive screws, labeled "1" through "4," in consecutive order.
Back to Contents Page Center Control Cover Dell™Latitude™D810ServiceManual Removing the Center Control Cover Removing the Center Control Cover 1. Follow the instructions in " Preparing to Work Inside the Computer .
Back to Contents Page Display Assembly Dell™Latitude™D810ServiceManual Display Assembly Display Bezel Display Panel Display Assembly 1. Follow the instructions in " Preparing to Work Inside the Computer .
Display Bezel 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the display assembly . 3. Use a plastic scribe to pry the six round display bumpers out of the screw holes located on the front of the bezel.
Display Panel 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the center control cover . 3. Remove the display assembly . 4. Remove the display bezel . Remove the eight M2 x 3 - mm screws from sides of the display panel.
9. Use the pull - tab to disconnect the bottom flex - cable connector from the inverter display - cable connector. Back to Contents Page 1 top flex - cable connector 2 top display - cable .
Back to Contents Page Fan Dell™Latitude™D810ServiceManual Removing the Fan Removing the Fan 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the center control cover . 3.
Back to Contents Page Fans Dell™Latitude™D810ServiceManual Removing the Microprocessor Fan 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the display assembly . 3. Remove the keyboard .
5. Remove the M2.5 x 5 - mm screw from the bottom right corner of the fan. 6. Disconnect the fan cable connector. 7. Lift the fan straight out of the computer.
Back to Contents Page Hard Drive Dell™Latitude™D810ServiceManual Removing the Hard Drive and Carrier 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Turn the computer over. Use a standard #1 Phillips screwdriver to remove the two M3 x 3 - mm screws.
Back to Contents Page .
Back to Contents Page Keyboard Dell™Latitude™D810ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Turn the computer top - side up and open it. 3. Remove the center control cover .
Back to Contents Page 1 M2.5 x 5 - mm screws (2) 2 keyboard 3 palm rest 4 keyboard tabs (5).
Back to Contents Page Palm Rest Dell™Latitude™D810ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the display assembly . 3. Remove the keyboard . 4. Remove the 13 M2.
8. Use your fingers to separate the palm rest from the computer base. 9. Lift the palm rest, pulling apart the snaps on the base. Back to Contents Page 1 touch pad connector 2 system board connector 3 computer base NOTICE: Carefully separate the palm rest from the computer base to avoid damage to the palm rest.
Back to Contents Page PC Card Reader Dell™Latitude™D810ServiceManual Removing the PC Card Reader 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the display assembly . 3.
Back to Contents Page Pin Assignments for I/O Connectors Dell™Latitude™D810ServiceManual USB Connector Video Connector S- Video TV - Out Connector Seria.
Serial Connector Back to Contents Page S- Video Pin Signal 1 GND 2 GND 3 DLUMA -L 4 DCRMA -L Composite Video Pin Signal 5 SP_DIF 6 DCMPS - L 7 SP_DIF Pin Signal.
Back to Contents Page Smart Card Reader Dell™Latitude™D810ServiceManual Removing the Smart Card Reader 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the display assembly .
Back to Contents Page Smart Card Reader Dell™Latitude™D810ServiceManual Removing the Smart Card Reader Removing the Smart Card Reader 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2.
Back to Contents Page Speakers Dell™Latitude™D810ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the coin - cell battery. 3. Remove the display assembly . 4.
Back to Contents Page System Board Dell™Latitude™D810ServiceManual Removing the System Board The system board's BIOS chip contains the Service Tag, which is also visible on a barcode label on the bottom of the computer.
19. Remove the M2 x 3 - mm screw from the system board support. 20. Remove the three M2.5 x 5 - mm screws that secure the system board to the computer base. 21. Remove the system board from the computer base. a. Ensure that you have disconnected all cables from the system board.
c. After the connectors are dislodged, lift the board out of the base. Installing the System Board 1. Perform all the steps in " Removing the System Board " in reverse order. 2. Turn on the computer. 3. Insert the floppy or CD that accompanied the replacement system board into the appropriate drive.
Back to Contents Page System Components Dell™Latitude™D810ServiceManual Back to Contents Page NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Back to Contents Page Thermal - Cooling Assembly Dell™Latitude™D810ServiceManual Removing the Thermal - Cooling Assembly Removing the Thermal - Cooling Assembly There is one thermal - cooling assembly for both the integrated video and the processor.
When replacing the thermal - cooling assembly, follow the steps in reverse order. Back to Contents Page .
Back to Contents Page Dell™Latitude™D810ServiceManual Notes, Notices, and Cautions Information in this document is subject to change without notice. © 2005DellInc.Allrightsreserved. Reproduction in any manner whatsoever without the written permission of Dell Inc.
Back to Contents Page Memory Modules, Mini PCI Card, Modem, and Devices Dell™Latitude™D810ServiceManual Memory Modules Mini PCI Card Modem Devices Memory Modules The computer has two memory slots, DIMM A and DIMM B.
4. Ground yourself and install the new memory module: a. Align the notch in the module with the slot in the center of the connector. b. Slide the edge of the module firmly into the connector, and rotate the module down until you feel a click.
5. Ground yourself and install the new memory module: a. Align the notch in the module with the slot in the center of the connector. b. Slide the edge of the module firmly into the connector, and rotate the module down until you feel a click.
2. Turn the computer over, and loosen the captive screws on the options cover. 3. If a Mini PCI card is not already installed, go to step4 . If you are replacing a Mini PCI card, remove the existing card: a. Disconnect the Mini PCI card from any attached cables.
4. To install the Mini PCI card, align the Mini PCI card with the connector at a 45 - degree angle, and press the Mini PCI card firmly into the connector. Press down until you feel a click. 5. Connect the antenna cables to the Mini PCI card. 6.
4. If you are installing a modem, connect the modem cable to the modem. 5. Align the modem with the screw hole, and press the modem into the connector directly over the connector on the system board. 6. Replace the M2 x 3mm modem screw and secure the modem to the system board.
2. Pull the device by the latch release to remove the device from the module bay. If the Device Screw Is Installed 1. If the computer is connected to a docking device (docked), undock it. See the documentation that came with your docking device for instructions.
5. Pull the device by the latch release to remove the device from the module bay. Back to Contents Page NOTICE: Insert devices into the module bay before you dock and turn on the computer.
Back to Contents Page Video Card Assembly Dell™Latitude™D810ServiceManual Removing the Video Card Assembly 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the display assembly .
デバイスDell D810の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Dell D810をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDell D810の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dell D810の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dell D810で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dell D810を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDell D810の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dell D810に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDell D810デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。