DellメーカーRW491の使用説明書/サービス説明書
ページ先へ移動 of 202
www .dell.com | support.dell.com Dell™ XPS™ M1330 Owner’ s Manual Model PP25L book.book Page 1 Tuesday, October 7, 2008 6:00 PM.
Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer . NOTICE: A NOTICE indicates either potential damage to ha rdware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury , or death.
Contents 3 Contents Finding Information . . . . . . . . . . . . . . . . . . . 13 1 About Y our Computer . . . . . . . . . . . . . . . 19 Determining Y our Co mputer’ s Configuration . . . . . . 19 Front View . . . . . . . . . . . . . . . . . . . . .
4 Contents Power Protection Devices . . . . . . . . . . . . . . . 35 Surge Protectors . . . . . . . . . . . . . . . . . . 35 Line Conditioners . . . . . . . . . . . . . . . . . . 36 Uninterruptible Powe r Supplies (UPS) . . . . . . . 36 3 Using the Sy stem Setup Program .
Contents 5 5 Using the Display . . . . . . . . . . . . . . . . . . 47 Adjusting Brightness . . . . . . . . . . . . . . . . . . 47 Switching the Video Ima ge From Y our Computer Display T o a Projector . . . . . . . . . . . . . . . . . . 47 Setting Display Reso lution and Refresh Rate .
6 Contents Copying CDs and DVDs . . . . . . . . . . . . . . . . . 60 How to Copy a CD or DVD . . . . . . . . . . . . . 60 Using Blank CDs and DVDs . . . . . . . . . . . . 60 Helpful T ips . . . . . . . . . . . . . . . . . . . . . 61 Adjusting the V olume .
Contents 7 10 Setting Up and Using Networks . . . . . . . 73 Connecting a Network or Broadband Modem Cable . . . . . . . . . . . . . . . . . . . . . . 73 Setting Up a Network . . . . . . . . . . . . . . . . . . 74 Wireless Local Ar ea Network (WLAN) .
8 Contents 12 T roubleshooting . . . . . . . . . . . . . . . . . . . . 87 Dell T echnical Update Service . . . . . . . . . . . . . 87 Dell Diagnostics . . . . . . . . . . . . . . . . . . . . . 87 Dell Support Center . . . . . . . . . . . . . . . . . .
Contents 9 Dell MediaDirect problems . . . . . . . . . . . . 106 Other software problems . . . . . . . . . . . . . 107 Memory Problems . . . . . . . . . . . . . . . . . . . . 108 Network Problems . . . . . . . . . . . . . . . . . . . 108 Mobile Broadband (Wi reless Wide Area Network [WW AN]) .
10 Contents 13 Adding and Replacing Parts . . . . . . . . . 127 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . 127 Recommended T ools . . . . . . . . . . . . . . . . 127 T urning Off Y our Computer . . . . . . . . . . . . . 127 Before W orking Inside Y our Computer .
Contents 11 Flash Cache Module (FCM) . . . . . . . . . . . . . . . 150 Removing the FCM . . . . . . . . . . . . . . . . . 150 Replacing the FCM . . . . . . . . . . . . . . . . . 151 Internal Card With Bluetooth ® Wireless T echnology . . . . . . . . .
12 Contents Product Information . . . . . . . . . . . . . . . . . . . 161 Returning Items for Warran ty Repair or Credit . . . . . 162 Before Y ou Call . . . . . . . . . . . . . . . . . . . . . 162 Contacting Dell . . . . . . . . . . . . . . . . . . .
Finding Information 13 Finding Information NOTE: Some features or media may be optional and ma y not ship with your computer . Some features or media may n ot be available in certain countries. NOTE: Additional information may ship with your computer .
14 Finding Information • W arranty information • T erms and Conditions (U.S. only) • Safety instructions • Regulatory information • Ergonomics information • End User License Agreement Dell™ Product Information Guide • How to set up my computer Setup Diagram NOTE: The appearance of your setup diagram may vary .
Finding Information 15 • Service T ag and Express Service Code • Microsoft ® W indows ® License Label Service T ag and Microsoft Windows Product Key These labels are located on your computer . • Use the Service T ag to identify your computer when you use support.
16 Finding Information • Solutions — T r oubleshooting hints and tips, articles from technicians, online courses, and frequently ask ed questions • Community — Online discussion with other Del.
Finding Information 17 • Software upgrades and troubleshooting hints — F requently asked questions, hot topics, and general health of your computing environment Dell Support Utility The Dell Support Utility is an automated upgrade and notification system installed on your computer .
18 Finding Information • How to reinstall my operating system Operating Sy stem Media The operating system is already installed on your computer . T o reinstall your operating system, use one of the.
About Y our Computer 19 About Y our Computer Determining Y our Computer’ s Configuration Based on selections that you made when purchasing your computer , your computer has one of several different video controller configurations. T o determine your computer ’s vid eo controller configuration: 1 C lick Start , and then click Help and Support .
20 About Y our Computer Front V iew 1 camera indicator 2 camera (optional) 3 display 4 media control buttons 5 keyboard 6 fingerprint reader (optional) 7 8-in-1 memory reader 8 microphone connector 9 .
About Y our Computer 21 CAMERA INDICATOR — Indicates that the camera is turned on. Based on configuration selections that you made when ordering your computer , your computer may not include a camera. CAMERA ( OPTIONAL )— Built-in camera for video capture, confer encing, and chat.
22 About Y our Computer FINGERPRINT READER ( OPTIONAL )— Helps to keep your Dell™ computer secur e. When you slide your finger over the read er , it uses your unique fingerprint to authenticate your user iden tity .
About Y our Computer 23 TOUCH PAD — P rovides the functionality of a mouse (see "T ouch P ad" on page 45). D ELL ™ M EDIA D IRECT ™ B UTTON — P ress the Dell MediaDirect button to launch Dell MediaDirect. F or more information, see "Using Dell MediaDirect™" on page 63.
24 About Y our Computer If the computer is connected to an elec trical outlet, the light operates as follows: – Solid blue: The battery is charging. – Flashing blue: The battery is almost fully charged.
About Y our Computer 25 AC ADAPTER CONNECTOR — Attaches an AC adapter to the computer . The AC adapter converts AC power to the DC p ower r equired by the computer . Y ou can connect the AC adapter with your computer turned on or off. CAUTION: The AC adapter works with electrica l outlets worldwide.
26 About Y our Computer NETWORK CONNECTOR (RJ-45) NOTICE: The network connector is slightly larger than the modem connector . T o avoid damaging the computer , do no t plug a telephone line into the network connector .
About Y our Computer 27 E XPRESS C ARD SLOT — Supports one ExpressCar d. The computer ships with a plastic blank installed in the slot. F or more info rmation, see "Using Expr essCards" on page 67. OPTICAL DRIVE — F or more information about the optical drive, see "Using Multimedia" on page 57.
28 About Y our Computer Back V iew AIR VENTS — The computer uses an internal fan to create airflow through the vents, which prevents the computer from over heating. NOTE: The computer turns the fa n on when the computer ge ts hot. Fan noise is normal and does not indicate a pr oblem with the fan or the computer .
About Y our Computer 29 Bottom V iew BATTERY — When a battery is installed, you can use the computer without connecting the computer to an electrical outlet (see "Using a Battery" on page 49). BATTERY RELEASE LATCH — Releases the battery (see "Replacing the Battery" on page 54 for instructions).
30 About Y our Computer MEMORY MODULE / COIN - CELL BATTERY COMPARTMENT — Covers the compartment that contains the DIMM 1 and DIMM 2 me mory modules and the coin-cell battery . F or additional informatio n, see "Adding and Replacing P arts" on page 127.
Setting Up Y our Computer 31 Setting Up Y our Computer Connecting to the Internet NOTE: ISPs and ISP offerings vary by country . T o connect to the Internet, you need a modem or network connection and an Internet service provider (ISP).
32 Setting Up Y our Computer Setting Up Y our Internet Connection T o set up an Internet connection wi th a provided ISP desktop shortcut: 1 Save and close any open files, and exit any open programs. 2 Double-click the ISP icon on the Microsoft ® W indows ® desktop.
Setting Up Y our Computer 33 T ransferring Information to a New Computer Y ou can transfer the following types of data from one computer to another: • E-mail messages • T oolbar settings • W ind.
34 Setting Up Y our Computer Printer Cable Y our printer connects to your computer us ing a USB cable. Y our printer may not come with a printer cable, so if you purchase a cable separately , ensure that it is compatible with your p rinter and computer .
Setting Up Y our Computer 35 3 T urn the printer on, and then turn the computer on. If the Add New Hardware Wizard window appears, click Cancel . 4 Click Start , and then click Network .
36 Setting Up Y our Computer Line Conditioners NOTICE: Line conditioners do not prote ct against powe r interruptions. Line conditioners are designed to main tain A C voltage at a fairly constant level. Uninterruptible Power Supplies (UPS) NOTICE: Loss of power while data is being saved to the hard drive may result in data loss or file damage.
Using the Sy stem Setup Program 37 Using the Sy stem Setup Program NOTE: Y our operating sy stem may automatica lly configure most of the options available in sy stem setup, thus overriding options that you set through sy stem setup. An exception is the External Hot Key option, which you can disable or enable only through sy stem setup.
38 Using the Sy stem Setup Program Viewing the Sy stem Setup Screen 1 T urn on (or restart) your computer . 2 When the DELL logo appears, press <F2> immediately . If you wait too long and the Microsof t W indows logo appears, continue to wait until you see the W indows desk top, then shut down your computer and try again.
Using the Sy stem Setup Program 39 • USB Storage Device • CD/D V D/CD-R W drive • Modular bay HDD NOTE: Only devices that are preceded by a number are bootable. During the boot routine, t he computer starts at the top of the list and scans each enabled device for the operating system start-up files.
40 Using the Sy stem Setup Program Cleaning Y our Computer CAUTION: Before you begin any of the proc edures in this section, follow the safety instructions located in the Product Information Guide .
Using the Sy stem Setup Program 41 T ouch Pad 1 Shut down and turn off your computer (see "T urning Off Y our Computer" on page 127). 2 Disconnect any attached devices from the computer and from their electrical outlets. 3 Remove any installed batteries (see "Battery P erformance" on page 49).
42 Using the Sy stem Setup Program Cleaning an Optical Mouse Clean the outside casing of the mouse with a cloth moistened with a mild cleaning solution. Media NOTICE: Alway s use compressed air to clean the lens in the optical drive, and follow the instructions that come with the compressed air produ ct.
Using the Keyboard and T ouch Pad 43 Using the Keyboard and T ouch Pad Numeric Keypad The numeric keypad functions lik e t he numeric keypad on an external key b o ard . • T o enable the keypad, press <Num Lk >. The light indicates that the keypad is active.
44 Using the Keyboard and T ouch Pad Power Management Microsoft ® Windows ® Logo Key Functions Dell™ QuickSet Key Combinations If Dell QuickSet is installed, you ca n use other shortcut keys for functions such as the Battery Meter or activating power management modes.
Using the Keyboard and T ouch Pad 45 T ouch Pad The touch pad detects the pressur e and movement of your finger to allow you to move the cursor on the display . Use the touch pad and touch pad buttons as you would use a mouse. • T o move the cursor , lightly slide your finger over the touch pad.
46 Using the Keyboard and T ouch Pad Customizing the T ouch Pad Y ou can use the Mouse P roperties window to disable the touch pad or adjust the touch pad settings. 1 Click Start , and then click Control Pa n e l . 2 Click Hardware and Sound . 3 Click Mouse.
Using the Display 47 Using the Display Adjusting Brightness When a Dell™ computer is running on battery power , you can conserve power by setting the display brightness to the lowest comfortable level. • P ress <Fn> and the up-arrow key to in cr ease brightness on the integrated display only (not on an external monitor).
48 Using the Display Y ou can enhance the legibility of text and change the appearance of images on the screen by adjusting display r eso lution. As you increase r esolution, items appear smaller on the screen. In contrast, lower r esolution causes text and images to appear larger and can benefit people with vision impairments.
Using a Battery 49 Using a Battery Battery Performance NOTE: For information about the Dell™ wa rranty for your computer , see the Product Information Guide or separate paper warranty document that shipped with your computer .
50 Using a Battery Y ou can check the battery charge befo r e you insert the battery into the computer . Y ou can also set power manage ment options to alert you when the battery charge is low . CAUTION: Using an incompatible battery may increase the risk of fire or explosion.
Using a Battery 51 F or more information about QuickSet , right-click the QuickSet icon, and then click Help . Microsoft ® Windows ® Battery Meter The battery meter indicates the rema ining battery char ge. T o check the battery meter , double-click the icon in the notification ar ea.
52 Using a Battery Low-Battery Warning NOTICE: T o avoid losing or corrupting data, sa ve your work immediately after a low-battery warning, then connect the computer to an electrical outlet. If the battery runs completely out of power , Sleep state begi ns automatically.
Using a Battery 53 Using the Sleep Power State Rather than shutting down your portable computer , use the Sleep power state to conserve power . Sleep automatically saves your work to your hard drive, and then returns you to your pr evious work session without restarting your computer .
54 Using a Battery Replacing the Battery CAUTION: Using an incompatible battery may increase the risk of fire or explosion. Replace the b attery only with a compatible battery purchased from Dell. The battery is designed to work w ith your Dell computer .
Using a Battery 55 Storing a Battery Remove the battery when you store your computer for an e xtended period of time. A battery discharges during prol onged storage. After a long storage period, rechar ge the battery fully (s ee "Charging the Battery" on page 53) before you use it.
56 Using a Battery book.book Page 56 Tuesday, October 7, 2008 6:00 PM.
Using Multimedia 57 Using Multimedia Playing Media NOTICE: Do not move the computer while playing media. 1 P ress the eject button located above the keyboar d on the center-control cover . 2 Slide the disc, label side up, in the drive opening. T o format media for storing or copying data, see the media software that came with your computer .
58 Using Multimedia A DVD drive includes the following basic buttons: F or more information on playing media, click Help on the media player (if available). Playing Media Using Dell T ravel Remote (Optional) The Dell T ravel Remote is designed to control Dell Media Direct and W indows Vista Media Center .
Using Multimedia 59 1 Infrared T ransmitter 2 Arrow Up 3 OK/Enter/Select 4 Arrow Right 5 Arrow Down 6 Play/Pause 7 Forward 8 Skip Forward 9 Stop 10 Skip Back 11 Reverse 12 Back 13 Arrow Left 14 Mute 15 V olume Down 16 Page Down 17 V olume Up 18 Page Up 1 2 3 4 5 6 7 8 9 14 13 12 11 10 17 15 18 16 book.
60 Using Multimedia Copying CDs and DVDs This section applies only to compu ters that have a D VD+/-RW drive. NOTE: Ensure that you observe all copy right laws when copying media. NOTE: The types of optical drives offered by Dell may vary by country .
Using Multimedia 61 Use blank CD-Rs to recor d music or p ermanently store data files. After creating a CD-R, you cannot write to that CD-R again (see the Sonic documentation for more information). Use a blank CD-R W if you plan to erase, rewrite, or update information on that disc later .
62 Using Multimedia • Use a blank CD-RW to practice CD r ecording until you ar e familiar with CD recor ding techniques. If you make a mistake, you can erase the data on the CD-R W and try again. Y ou can also use blank CD-RWs to test music file projects before you r ecord the project permanently to a blank CD-R.
Using Multimedia 63 Using Dell MediaDirect™ Dell MediaDirect is an instant-on mu ltimedia playback mode for digital media. P ress the Dell MediaDirect bu tton, located on the hinge cover , to launch Dell MediaDirect.
64 Using Multimedia Connecting Y our Computer to a TV Using the HDMI Connector Y our computer features a high-defini tion multimedia interface (HDMI) connector , which allows you to connect the computer to a high-definition TV .
Using Multimedia 65 4 Click the tab for your video card. NOTE: T o determine the type of video card installed in your computer , see Windows Help and Support. T o access Help and Support, click Start → Help and Support . Under Pick a T ask , click Use T ools to view your computer information and diagnose problems.
66 Using Multimedia book.book Page 66 Tuesday, October 7, 2008 6:00 PM.
Using ExpressCards 67 Using ExpressCards ExpressCar ds provide additional memo ry , multimedia, wired and wireless communications, and security features . F or example, you can add an ExpressCar d to make wire less wide area network (WW AN) connectivity available on your computer .
68 Using ExpressCards Installing an ExpressCard Y ou can install an ExpressCar d whil e the computer is running. The computer automatically detects the card. ExpressCar ds are generally marked with a symbol (such as a triangle or an arrow) or a label to indicate which end to insert into the slot.
Using ExpressCards 69 Removing an ExpressCard or Blank CAUTION: Before you begin any of the proced ures in this section, follow the safety instructions in the Product Information Guide . NOTICE: When installing or removing an expr ess card, please do not push express card and latch simultaneou sly .
70 Using ExpressCards book.book Page 70 Tuesday, October 7, 2008 6:00 PM.
Using the Memory Card Reader 71 Using the Memory Card Reader The memory card r eader provides a fast and convenient way to view and share digital photos, music, and vide os store d on a memory card. NOTE: A memory card reader is not a bootable device.
72 Using the Memory Card Reader CAUTION: Before you begin any of the proc edures in this section, follow the safety instructions in the Product Information Guide . T o install a memory card: 1 Hold the card with the top side of the car d facing up. 2 Slide the card into the slot until the car d is completely seated in its connector .
Setting Up and Using Networks 73 Setting Up and Using Networks Setting up a computer network provid es connectivity between your computer and the Internet, another computer , or a network.
74 Setting Up and Using Networks Setting Up a Network 1 Click Start , and then click Connect T o . 2 Click Set up a connection or network . 3 Select an option under Choose a connection option . 4 Click Next , and then follow the instructions in the wizard.
Setting Up and Using Networks 75 Device Manager 1 Click Start , and then click Control P anel . 2 Click Classic V iew on the menu on the left side of the Control P anel . 3 Double-click Device Manager . NOTE: The User Account Control window may open. 4 Click Continue on the User Account Control window if it opens.
76 Setting Up and Using Networks 7 Disconnect the AC adapter cable from your wir eless router to ensure that there is no power connected to the router . NOTE: W ait for a minimum of 5 minutes af ter disconnecting your broadband modem before continuing with the network setup.
Setting Up and Using Networks 77 Connecting to a WLAN NOTE: Before you connect to a WLAN, ensu re that you have followed the instructions in "Wireless Local Area Network (WLAN)" on page 74. NOTE: The following networking instructions do not apply to internal cards with Bluetooth ® wireless technology or cellular products.
78 Setting Up and Using Networks Monitoring the Status of the Wireles s Network Card Through Dell QuickSet The wireless activity indicator provides you with an easy way to monitor the status of your computer ’s wireless devices. T o turn the wireless activity indicator on or off, click the QuickSet icon in the taskbar and select Hotkey P opups .
Setting Up and Using Networks 79 T o set up a Mobile Broadband network connection, you need: • A Mobile Broadband ExpressCar d or mini-card (depending on your computer ’s configuration) NOTE: For instructions on u sing ExpressCards, see "Using ExpressCards" on page 67.
80 Setting Up and Using Networks Connecting to a Mobile Broadband Network NOTE: These instructions only apply to Mobile Broadband ExpressCards or Mini- Cards. They do not apply to internal cards with wireless technology . NOTE: Before you connect to the Internet, you must act ivate Mobile Broadband service through your cellular service provider .
Setting Up and Using Networks 81 If the switch is in the "on" position, move the switch to the "off" position to disable the switch and the Mobile Broadban d card. If the switch is in the "off" position, move the switch to the "on" position to enable the switch and the Dell Mobile Broadband card.
82 Setting Up and Using Networks book.book Page 82 Tuesday, October 7, 2008 6:00 PM.
Securing Y our Computer 83 Securing Y our Computer Security Cable Lock NOTE: Y our computer does not ship wi th a security cable lock. A security cable lock is a commercially available antitheft device. T o use the lock, attach it to the security cable slot on your Dell™ computer .
84 Securing Y our Computer When using passwords, observ e the following guidelines: • Choose a password that you can r emember , but not one that is easy to guess. F or example, do not use the names of family members or pets for passwor ds. • It is recommended that you do not write down your password.
Securing Y our Computer 85 If Y our Computer Is Lost or Stolen • Call a law enforcement agency to re port the lost or stolen computer . Include the Service T ag in your descri ption of the computer . Ask that a case number be assigned and write down the number , along with the name, address, and phone number of the law enforcement agency .
86 Securing Y our Computer book.book Page 86 Tuesday, October 7, 2008 6:00 PM.
T roubleshooting 87 T roubleshooting Dell T echnical Update Service The Dell T echnical Update service provides proactive e-mail notification of software and har dware updates for your computer . The service is free and can be customized for content, format, and how frequently you r eceive notifications.
88 T roubleshooting Starting the Dell Diagnostic s From Y our Hard Drive The Dell Diagnostics is located on a hidden diagnostic utility partition on your hard drive. NOTE: If your computer cannot display a screen image, c ontact Dell (see "Contacting Dell" on page 164).
T roubleshooting 89 Starting the Dell Diagnostics From the Drivers and Utilities Media 1 Insert your Drivers and Utilities media. 2 Shut down and restart the computer .
90 T roubleshooting Dell Diagnostics Main Menu After the Dell Diagno stics loads and the Main Menu screen appears, click the button for the option you want. NOTE: It is recommended that you select Test System to run a complete test on your computer . After you have selected the Test System option from the main menu, the following menu appears.
T roubleshooting 91 The following tabs provide additional information for tests run from the Custom T est or Symptom T ree option: Dell Support Center The Dell Support Center helps you find the service, support and system-specific information you need.
92 T roubleshooting Click the Dell Support Center icon on your computer ’s desktop to run the application and to access the following features: • Self -help tools such as, Dell Suppo rt 3, Dell PC.
T roubleshooting 93 F or more information about Dell Support 3, click the question mark ( ? ) at the top of the Dell Support 3 window . T o access Dell Support 3: • Click the Dell Support 3 icon in the notification area of your W indows desktop. NOTE: The icon functions vary dependi ng on whether you click, double- click, or right-click the icon.
94 T roubleshooting Dell Network Assistant Designed specifically for users of De ll™ computers, the Dell Network Assistant helps simplify the setup, monitoring, tr oubleshooting, and repair of your network.
T roubleshooting 95 E NSURE THAT M ICROSOFT W INDOWS RECOGNIZES THE DRIVE — • Click Start → Computer . If the drive is not listed, perform a full scan with your antivirus software to check for and remove viruses. V iruses can sometimes prevent W i ndows from recognizing the drive.
96 T roubleshooting The drive makes an unfamiliar scraping or grinding sound • Ensure that the sound is not cause d by the program that is running. • Ensure that the disc is inserted properly . Hard drive problems A LLOW THE COMPUTER TO COOL BEFORE TURNING IT ON — A hot hard drive may prevent the operating system from star ting.
T roubleshooting 97 U SE A DIFFERENT TELEPHONE LINE • V erify that the telephone line is conne cted to the jack on the modem (the jack has either a green label or a co nnector -shaped icon next to it). • Ensure that you hear a click when you insert the telephone line connector into the modem.
98 T roubleshooting Error Messages F ill out the "Diagnostics Checklist" on page 163 as you complete these checks. CAUTION: Before you begin any of the proc edures in this section, follow the safety instructions in the Product Information Guide .
T roubleshooting 99 T HE FILE BEING COPIED IS TOO LARGE FOR THE DESTINATION DRIVE — The file that you are trying to copy is too lar ge to fit on the disk, or the disk is full. T ry copying the file to a different disk or use a lar ger capacity disk.
100 T roubleshooting P ROGRAM — The system configuration info rmation does not match the hardwar e configuration. The message is most likely to occur after a memory module is installed. Correct the appr opriate options in the system setup program (see "Dell T echnical Support P olicy (U.
T roubleshooting 101 VALUE — A memory module may be faulty or improperly seated. Reinstall the memory modules and, if necessary , replace them (see "Memory" on page 137). M EMORY WRITE / READ FAILURE AT ADDRESS , READ VALUE EXPECTING VALUE — A memory module may be faulty or im properly seated.
102 T roubleshooting S EEK ERROR — The operating system cannot find a specific track on the hard drive. S HUTDOWN FAILURE — A chip on the system board may be malfunctioning. R un the System Set tests in the Dell Diagnostics (see "Dell Diagnostics" on page 87).
T roubleshooting 103 ExpressCard Problems CAUTION: Before you begin any of the proced ures in this section, follow the safety instructions in the Product Information Guide . C HECK THE E XPRESS C ARD — Ensure that the Expr essCard is properly inserted into the connector .
104 T roubleshooting Keyboard Problems CAUTION: Before you begin any of the proc edures in this section, follow the safety instructions in the Product Information Guide . F ill out the "Diagnostics Checklist" on page 163 as you perform the various checks.
T roubleshooting 105 4 F rom the W indows desktop, click Start → All P rograms → Accessories → Notepad . 5 T ype some characters on the internal keyboar d and verify that they appear on the display . If the characters appear now , but did not with the external k eyboard, you may have a defective external k eyboard.
106 T roubleshooting A program stops responding or crashes repeatedly E ND THE PROGRAM — 1 P ress <Crtl><Shift><Esc> simultaneously . 2 Click the Applications tab and select the pro gram that is no longer responding. 3 Click End T ask .
T roubleshooting 107 C ANNOT PLAY SOME MEDIA FILES — Because Dell MediaDirect provides access to media files outside the W indows op erating system environment, access to licensed content is restricted. Licensed content is digital content that has Digital Rights Management (DRM) appl ied to it.
108 T roubleshooting R UN THE D ELL D IAGNOSTICS — If all tests run successfully , the error condition is related to a softwar e problem (see "Dell Diagnostics" on page 87). Memory Problems F ill out the "Diagnostics Checklist" on page 163 as you complete these checks.
T roubleshooting 109 R ESTART THE COMPUTER AND LOG ON TO THE NETWORK AGAIN C HECK YOUR NETWORK SETTINGS — Contact your network administrator or the person who set up your network to verify that your network settings are correct and that the network is functioning.
110 T roubleshooting Power Problems F ill out the "Diagnostics Checklist" on page 163 as you complete these checks. CAUTION: Before you begin any of the proc edures in this section, follow the safety instructions in the Product Information Guide .
T roubleshooting 111 C ONNECT THE COMPUTER DIRECTLY TO AN ELECTRICAL OUTLET — Bypass power protection devices, power strips, and extension cables to verify that the computer turns on. E LIMINATE POSSIBLE INTERFERENCE — T urn off nearby fans, fluorescent lights, halogen lamps, or other appliances.
112 T roubleshooting Scanner Problems CAUTION: Before you begin any of the proc edures in this section, follow the safety instructions in the Product Information Guide . NOTE: If you need technical a ssistance for your scanne r , contact the scanner’ s manufacturer .
T roubleshooting 113 No sound from external speakers E NSURE THAT THE SUBWOOFER AND THE SPEAKERS ARE TURNED ON — See the setup diagram supplied with the spea kers. If your speak ers have volume controls, adjust the volume, bass, or treble to eliminate distortion.
114 T roubleshooting C HECK THE MOUSE CABLE — Shut down the computer , disconnect the mouse cable and check it for damage, then firmly reconnect the cable. If you are using a mouse e xtension cable, disconnect it and connect the mouse directly to the computer .
T roubleshooting 115 T EST THE ELECTRICAL OUTLET — Ensure that the electrical outlet is working by testing it with another device, such as a lamp. C HECK THE AC ADAPTER — Check the AC adapter cabl e connections. If the AC adapter has a light, ensur e that the light is on.
116 T roubleshooting If only part of the display is readable C ONNECT AN EXTERNAL MONITOR — 1 Shut down your computer and connect an external monitor to the computer . 2 T urn on the computer and the mo nitor , and then adjust the monitor brightness and contrast controls.
T roubleshooting 117 Identifying Drivers If you experience a problem with any de vice, identify whether the driver is the source of your problem and, if necessary , update the driver . 1 Click Start , and then right-click Computer . 2 Click P roperties , and then click Device Manager .
118 T roubleshooting Using the Drivers and Utilities Media If using Device Driver Rollback or Syst em Restore (see "Restoring Y our Microsoft® W indows Vista® Operating System" on page 120) does not resolve the problem, r einstall the driver from your Drivers and Utilities media.
T roubleshooting 119 Manually Reinstalling Drivers NOTE: If your computer has a Consumer IR port and you are reinstalling a Consumer IR driver , you must first enable the Consumer IR port in the sy stem setup program (see "Dell T echni cal Support Policy (U.
120 T roubleshooting T o start the Hardware T roubleshooter: 1 Click Start and click Help and Support . 2 In the F ind an answer section, click T roubleshooting .
T roubleshooting 121 Using Windows Vista Sy stem Restore The W indows operating system provid es System Restore to allow you to return your computer to an earlier operating state (without affecting data files) if changes to the hardwar e, software, or other system settings have left the computer in an undesirable operat ing state.
122 T roubleshooting NOTICE: Before you restore the computer to an earlier operating state, save and close all open files and e xit any open programs. Do not alter , open, or delete any files or programs until the sy stem restoration is complete. 1 Click Start → Control P anel → System and Maintenance → Back Up and Restore Center .
T roubleshooting 123 Restoring the Computer to the Default Factory Configuration The Dell F actory Image Restore option allows you to restor e your hard drive back to its original fact ory configuration as when yo u first purchased it from Dell.
124 T roubleshooting Using the Operating Sy stem Media Before Y ou Begin If you are considering r einstalling the Windows operating system to corr ect a problem with a newly installed driver , first try using W indows Device Driver Rollback (see "Using W indows Device Driver Rollback" on page 117).
T roubleshooting 125 4 Restart the computer . When the DELL logo appears, press <F12> immediately . NOTE: If you wait too long and the oper ating sy stem logo appears, continue to wait until you see the Microsoft Windows desktop, then shut down your computer and try again.
126 T roubleshooting book.book Page 126 Tuesday, October 7, 2008 6:00 PM.
Adding and Replacing Parts 127 Adding and Replacing Parts Before Y ou Begin This chapter provides procedures for r emoving and installing the components in your computer .
128 Adding and Replacing Parts Before W orking Inside Y our Computer Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety . CAUTION: Before you begin any of the proc edures in this section, follow the safety instructions in the Product Information Guide .
Adding and Replacing Parts 129 5 Close the cover , turn the computer over , and place the computer on a flat surface. 6 Slide and click the battery release latch. 7 Slide the battery out of the battery bay . 8 T urn the computer top-side up, open the display , and press the power button to ground the system board.
130 Adding and Replacing Parts NOTE: Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell. NOTE: If you are installing a hard drive fr om a source othe.
Adding and Replacing Parts 131 Replacing the Hard Drive 1 Remove the new drive from its packaging. Save the original packaging for storing or shipping the hard drive. NOTICE: Use firm and even pressure to slide the drive into place. If you use excessive force, you may damage the connector .
132 Adding and Replacing Parts Hinge Covers and Center Control Cover CAUTION: Before you begin any of the proc edures in this section, follow the safety instructions in the Product Information Guide .
Adding and Replacing Parts 133 5 Ease the center control cover up, and re move the cable that attaches it to the system board. 1 center control cover 2 hinge cover (2) 2 1 book.
134 Adding and Replacing Parts Replacing the Hinge Covers and Center Control Cover 1 Reconnect the cable that attaches the center control cover to the system board, and snap the center control cover in place.
Adding and Replacing Parts 135 Keyboard F or more information about the k eyb oard, see "Using the Ke yboard and T ouch P ad" on page 43. CAUTION: Before you begin any of the proced ures in this section, follow the safety instructions in the Product Information Guide .
136 Adding and Replacing Parts 5 P ull up on the plastic bar that secures the keyboar d cable to the system board and r emove the keyboard Replacing the Keyboard 1 Slide the keyboar d connector into the slot until it clicks and pull down on the plastic bar that secures the k eyb oard connector to the system board.
Adding and Replacing Parts 137 Memory CAUTION: Before you begin any of the proced ures in this section, follow the safety instructions in the Product Information Guide . Y ou can increase your computer memory by installing memory modules on the system board.
138 Adding and Replacing Parts NOTICE: T o prevent damage to the memory m odule connector , do not use tools to spread the memory mo dule securing clips. 3 Use your fingertips to carefully spr ead apart the securing clips on each end of the memory module connect or until the module pops up.
Adding and Replacing Parts 139 Replacing the DIMM 1 Memory Module NOTICE: T o avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by peri odically touching an unpainte d metal surface (such as a connector on the bac k of the computer).
140 Adding and Replacing Parts 3 Replace the module cover . 4 Insert the battery into the battery bay , or connect the AC adapter to your computer and an electrical outlet. 5 T urn on the computer . As the computer boots, it detects th e additional memory and automatically updates the system configuration information.
Adding and Replacing Parts 141 NOTICE: T o prevent damage to th e memory module connec tor , do not use tools to spread the memory mo dule securing clips.
142 Adding and Replacing Parts 4 Remove the module from the connector . Replacing the DIMM 2 Memory Module NOTICE: T o avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by peri odically touching an unpainted metal surface (such as a connector on the ba ck of the computer).
Adding and Replacing Parts 143 NOTICE: If the cover is difficult to close, remove the module and reinstall it. Forcing the cover to close may damage your computer . 3 Replace the module cover . 4 Insert the battery into the battery bay , or connect the AC adapter to your computer and an electrical outlet.
144 Adding and Replacing Parts Subscriber Identity Module Subscriber Identity Modules (SIM) id entify users uniquely through an International Mobile Subscriber Identity . CAUTION: Before you begin any of the proc edures in this section, follow the safety instructions in the Product Information Guide .
Adding and Replacing Parts 145 Removing a WLAN Card 1 F ollow the procedur es in "Before Y ou Begin" on page 127. 2 T urn the computer over . 3 Loosen the captive screw on the co ver of the mini-card compartment and remove the cover . 1 captive screw 1 book.
146 Adding and Replacing Parts 4 Disconnect the antenna cables from the WLAN card. 5 Release the WLAN ca rd b y rem o vi n g t h e s c rew . 6 Lift the WLAN card out of its system board connector . 1W L A N C a r d 2 M2 x 3-mm screw 3 antenna cable connectors (2) 3 2 1 book.
Adding and Replacing Parts 147 Replacing a WLAN Card NOTICE: The connectors are keyed to ensure correct insertio n. If you feel resistance, check the connectors on the card and on the sy stem board, and realign the card. NOTICE: T o avoid damage to the WLAN card, never place cables under the card.
148 Adding and Replacing Parts 3 Loosen the captive screw on the cov er of the mini-card compartment and remove the cover . 4 Disconnect the two antenna cables from the WW AN card. 1 captive screw 1W W A N C a r d 2 M2 x 3-mm screw 3 antenna cable connectors (2) 1 3 2 1 book.
Adding and Replacing Parts 149 5 Release the WW AN card by r emoving the screw . 6 Lift the WW AN card out of its system board connector . Replacing a WWAN Card NOTICE: The connectors are keyed to ensure correct insertio n. If you feel resistance, check the connectors on the card and on the sy stem board, and realign the card.
150 Adding and Replacing Parts Flash Cache Module (FCM) The FCM is an internal memory card th at helps improve the performance of your computer . The FCM card is also known as Intel T urbo Memory and the Intel Flash Cache Logic Chip Mini-card. NOTE: This card is only compatible with the Microsoft Windows Vista™ operating sy stem.
Adding and Replacing Parts 151 Replacing the FCM NOTICE: Install the FCM in the WW AN or WP AN slot. Do n ot install an FCM in the WLAN card slot. Doing so may cause damage to your computer . 1 Insert the FCM connector at a 45-degree angle into the system boar d connector labeled "FCM".
152 Adding and Replacing Parts Replacing the Card 1 Replace the card at an angle to slide it under the securing tabs in the car d compartment. 2 Connect the cable to the card. Coin-Cell Battery CAUTION: Before you begin any of the proc edures in this section, follow the safety instructions in the Product Information Guide .
Adding and Replacing Parts 153 Removing the Coin-Cell Battery 1 F ollow the procedur es in "Before Y ou Begin" on page 127. 2 T urn the computer over and loosen th e three captive scr ews along with the M2.5 x 5-mm screw . Remove the module cover .
154 Adding and Replacing Parts book.book Page 154 Tuesday, October 7, 2008 6:00 PM.
Dell™ QuickSet 155 Dell™ QuickSet NOTE: This feature may not be available on your computer . Dell QuickSet provides you with easy access to configure or view the following types of settings: • N.
156 Dell™ QuickSet book.book Page 156 Tuesday, October 7, 2008 6:00 PM.
T raveling With Y our Computer 157 T raveling With Y our Computer Identifying Y our Computer • Attach a name tag or business card to the computer . • W rite down your Service T ag and s tor e it in a safe place away from the computer or carrying case.
158 T raveling With Y our Computer • P rotect the computer , the batteries, a nd the hard drive from hazards such as extr eme temperatures and overe xposure to sunlight, dirt, dust, or liquids. • P ack the computer so that it does no t slide around in the trunk of your car or in an overhead storage compartment.
Getting Help 159 Getting Help Obtaining Assistance CAUTION: If you need to remove the comp uter cover , first disconnect the computer power and modem c ables from all electrical outlets.
160 Getting Help T echnical Support and Customer Service Dell's support service is available to answer your questions about Dell™ hardwar e. Our support staff uses computer-based diagnostics to provide fast, accurate answers.
Getting Help 161 • Dell Marketing and Sales e-mail addr esses apmarketing@dell.com (Asian/P acific countries only) sales_canada@dell.com (Canada only) • Anonymous file transfer protocol (FTP) ftp.dell.com Log in as user: anonymous , and use your e-mail address as your passwor d.
162 Getting Help Returning Items for W arranty Repair or Credit P repare all items being r eturned, whether for repair or credit, as follows: 1 Call Dell to obtain a Return Materi al Authorization Number , and write it clearly and prominently on the outside of the box.
Getting Help 163 Diagnostics Checklist Name: Date: Address: Phone number: Service T ag (bar code on the back or bottom of the computer): Express Servi ce Code: Return Material Authorization Number ( i.
164 Getting Help Contacting Dell NOTE: If you do not have an active Internet connection, yo u can find contact information on your purchase invoice, pa cking slip, bill, or Dell product catalog. Dell provides several online and teleph one-based support and service options.
Specifications 165 Specifications NOTE: Offerings may vary by region. Fo r more information regarding the configuration of yo ur computer , click Start , click Help and Support , and then select the option to view information about your computer .
166 Specifications Cards supported ExpressCard/34 (34 mm) ExpressCar d/54 (54 mm) 1.5 V and 3.3 V ExpressCar d connector size 26 pins 8-in-1 Memory Card Reader 8-in-1 memory card controller Ricoh R5C8.
Specifications 167 Ports and Connectors Audio microphone connector , stereo headphone/speakers connector IEEE 1394 4-pin serial connector Consumer IR sensor compatible with Philips RC6 (receive only) Mini-card three T ype IIIA mini-card slots HDMI connector 19-pin Network adapter RJ-45 port USB two 4-pin USB 2.
168 Specifications Video type: discrete video car d Data bus PCI Express X16 Video controller nVIDIA GeF orce 8400M GS Video memory 128 MB GeF orce 8400M GS LCD interface LV D S TV support HDMI mode Audio Audio type 5.
Specifications 169 Operating angle 0 ° (closed) to 140° Luminance 250 min. 300 typ. cd/m² (LED 5 point avg) 200 min. 220 typ. cd/m² (CCFL 5 point avg) Viewing angles: Horizontal ±40° (CCFL) min. ±50° (LED) min. V ertical +15°/–30° (CCFL) min.
170 Specifications Battery T ype 9-cell "smart" lithium ion 6-cell "smart" lithium ion Dimensions: Depth 67.6 mm (2.66 inches) (9 cell) 47.5 mm (1.87 inches) (6 cell) Height 20.4 mm (0.8 inch) Wi d t h 209.9 mm (8.26 inches) W eight 0.
Specifications 171 AC Adapter T ypes 65W (D-Series) 90W (D-Series and E-Series) Input voltage 100–240 V AC Input current (maximum) 1.5 A/1.6 A Input frequency 50–60 Hz Output current 65W 3.9 A (maximum at 4-second pulse) 3.34 A (continuous) 90W 5.
172 Specifications 1 Using a random vibration spectrum that simulates user environment. 2 Measured with hard drive in operating status and a 2-ms half-sine pulse for operating. Also measured with hard drive in head-parked pos ition and a 2-ms halfsine pluse for storage.
Appendix 173 Appendix Dell T echnical Support Policy (U.S. Only) T echnician assisted technical supp ort requir es the cooperation and participation of the customer in the tr oubleshooting process and.
174 Appendix Definition of "Third-Party" Software and Peripherals Third-party softwar e and peripherals include any peripheral, accessory , or software program sold by Dell not un der the Dell brand (printers, scanners, cameras, games, etc).
Appendix 175 The following information is provided on the device or devices covered in this document in compliance with the FCC regulations: Macrovision Product Notice This product incorporates copy protecti on technology that is protected by U.
176 Appendix book.book Page 176 Tuesday, October 7, 2008 6:00 PM.
Glossary 177 Glossary T erms in this Glossary are provided fo r informational purposes only and may or may not describe features inclu ded with your particular computer . A AC — alternating current — The form of electricity that powers your computer when you plug the AC adapter power cable in to an electrical outlet.
178 Glossary BIOS — basic input/output system — A prog ram (or utility) that serves as an interface between the computer hardwar e and the operating system. Unless you understand what effect these settings have on the computer , do not change them.
Glossary 179 CD-R — CD recor dable — A recordable version of a CD. Data can be r ecorded only once onto a CD-R. Once recor ded, the data cannot be erased or written over . CD-R W — CD rewritable — A rewritable version of a CD. Data can be written to a CD-R W disc, and then erased and written over (rewritten).
180 Glossary DIMM — dual in-line memory module — A circuit board with memory chips that connects to a memory module on the system board. DIN connector — A round, six-pin connector th at conforms to DIN (Deutsche Industrie-Norm) standards; it is typically used to connect PS/2 k eyboard or mouse cable connectors.
Glossary 181 D VD+RW drive — drive that can r ead DVDs and most CD media and write to D VD+RW (r ewritable DVDs) discs. DV I — digital video interface — A standard for digital transmission between a computer and a digital video display .
182 Glossary F Fa h r e n h e i t — A temperature measurement scale wher e 32° is the freezing point and 212° is the boiling point of water . FBD — fully-buffered DIMM — A DIMM with DDR2 DR AM chips and an Advanced Memory Buffer (AMB) that speeds communication between the DDR2 SDR AM chips and the system.
Glossary 183 H hard drive — A drive that reads and writes data on a hard disk. The terms har d drive and hard di sk are often used interchangeably . heat sink — A metal plate on some proce ssors that helps dissipate heat.
184 Glossary I/O address — An address in R AM that is associat ed with a specific device (such as a serial connector , parallel connector , or ex pansion slot) and allows the processor to communicate with that device. IrD A — Infrared Data Association — The or ganization that cr eates international standards for infrar ed communications.
Glossary 185 M Mb — megabit — A measuremen t of memory chip capacity that equals 1024 Kb. Mbps — megabits per second — One million bits per second. This measurement is typically used for transmission speeds for networks and modems. MB — megabyte — A measurement of data st orage that equals 1,048,576 bytes.
186 Glossary modem — A device that allows your computer to communicate with other computers over analog telephone lines. Three types of modems include: e xternal, PC Card, and internal. Y ou typically use your modem to co nnect to the Internet and exchange e-mail.
Glossary 187 PC Card — A removable I/O car d adhering to the PCMCIA standard. Modems and network adapters are common types of PC Car ds. PCI — peripheral component interconnect — PCI is a local bus that supports 32-and 64-bit data paths, providing a high-speed data path betwee n the processor and devices such as video , drives, and networks.
188 Glossary RAM — random-access memory — The primary temporary storage area for program instructions and data. Any information stored in R AM is lost when you shut down your computer . readme file — A text file included with a softwar e package or hardware product.
Glossary 189 ScanDisk — A Microsoft utility that checks files , folders, and the hard disk’s surface for errors. ScanDisk often runs when yo u restart the computer after it has stopped responding.
190 Glossary surge protectors — P revent voltage spik es, such as those that may occur during an electrical storm, from entering the co mputer through the electrical outlet.
Glossary 191 U UAC — user account control— Microsoft Windows ® V ista™ security feature that , when enabled, provides an added layer of security between user accounts and access to operating system settings. UMA — unified memory allocation — System memory dynamically allocated to video .
192 Glossary video resolution — See resolution . virus — A program that is designed to inconvenience you or to destroy data stored on your computer . A virus program moves fr om one computer to another through an infected disk, software downloaded from th e Internet, or e-mail attachments.
Glossary 193 X XGA — extended graphics array — A video st andar d for video ca rds and controllers that supports resoluti ons up to 1024 x 768. Z ZIF — zero insertion force — A type of so cket or connector that allows a computer chip to be installed or removed with no st r ess applied to either the chip or its socket.
194 Glossary book.book Page 194 Tuesday, October 7, 2008 6:00 PM.
Index 195 Index Numerics 8-in-1 memory c ard r eader , 71 A audio . See sound B battery charge gauge, 5 1 charging, 5 3 checking the charge, 5 0 performance, 4 9 power meter , 5 1 removing, 5 4 replac.
196 Index copying D VDs general information, 6 0 helpful tips, 6 1 how to , 6 0 D Dell contacting, 1 6 4 Dell Diagnostics about, 8 7 starting from the Drivers and Utilities media, 8 9 starting from yo.
Index 197 ExpressCar ds, 67 b l a n k s , 67, 69, 71 installing, 6 8 removing, 6 9 F FCM. See Flash Cache Module Flash Cache Module, 150 H hard drive problems, 9 6 replacing, 1 2 9 returning to Dell, .
198 Index memory car d reader , 71 memory module cover description, 3 0 messages error , 9 8 Mini-Card installing, 1 4 4 Mobile Broadband network connections, 7 8 p r o b l e m s , 108 See also wireless switch modem connector description, 2 9 monitor .
Index 199 hard drive, 9 6 IEEE 1394 connector , 1 0 3 k e y b o a r d , 104 lockups, 1 0 5 network, 1 0 8 p o w e r , 110 power light conditions, 1 1 0 printer , 1 1 1 program crashes repeatedly , 1 0.
200 Index support contacting Dell, 1 6 4 support website, 16 System Restore, 120-121 system setup program commonly used options, 3 8 screens, 3 8 viewing, 3 8 T taskbar QuickSet icon, 1 5 5 telephone .
Index 201 W indows Vista P rogram Compatibility w i z a r d , 106 reinstalling, 1 2 1 S y s t e m R e s t o r e , 120-121 W indows Easy T ransfer wizard, 3 3 wireless turning activity on and off, 1 5 .
202 Index book.book Page 202 Tuesday, October 7, 2008 6:00 PM.
デバイスDell RW491の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Dell RW491をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDell RW491の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dell RW491の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dell RW491で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dell RW491を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDell RW491の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dell RW491に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDell RW491デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。