DellメーカーTL2000の使用説明書/サービス説明書
ページ先へ移動 of 264
De ll ™ P o wer V au lt ™ TL2 000 T ape Lib ra r y an d TL4000 T ape Lib rary U s e r’s Gu i d e.
.
De ll ™ P o we r V au lt ™ TL2 000 T ape Lib ra r y an d TL4000 T ape Lib rary U s e r’s Gu i d e.
Information in this document is subject to change without notice. © 2008 Dell Inc. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. T rademarks used in this text: Dell, the DELL logo and PowerV ault are trademarks of Dell Inc.
Read this First Minimum Firmware Levels for Common Library Features T able 1. Minimum Firmware Levels for common Library features Feature Minimum Firmware Level(s) Required Dedicated Cleaning Slot removal Library firmwar e level must be gr eater than 3.
iv Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Contents Read this First . . . . . . . . . . . . iii Minimum Firmware Levels for Common Library Features . . . . . . . . . . . . . . . iii Contacting Dell . . . . . . . . . . . . . iii Figures . . . . . . . . . . . . . . vii T ables . . . . . . . . . .
Data Cartridges . . . . . . . . . . . . . 6-1 Cartridge Compatibility . . . . . . . . . 6-2 WORM (W rite Once, Read Many) . . . . . . . 6-2 WORM Media . . . . . . . . . . . . 6-3 Data Security on WORM Media . . . . . . 6-3 WORM Media Errors . . . . . .
Figures 1-1. Front panel of a 2U library . . . . . . 1-1 1-2. Front panel of a 4U library . . . . . . 1-2 1-3. Rear panel of a 2U library with a SCSI drive 1-3 1-4. Rear panel of a 4U library with Full height Fibre Channel drive and Half height SCSI and SAS drives .
5-26. The 4U library Monitor Library: Drive Identity page showing one Fibre Channel drive (#1) and one SCSI drive (#2) . . . . 5-33 5-27. The 4U library Monitor Library: Library Status page . . . . . . . . . . . 5-34 5-28. The 4U library Monitor Library: Drive Status page .
T ables 1. Minimum Firmware Levels for common Library features . . . . . . . . . . iii 1-1. 2U library and 4U library front panel descriptions . . . . . . . . . . . 1-2 1-2. 2U library and 4U library rear panel descriptions . . . . . . . . . . . 1-4 1-3.
x Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Safety and Environmental Notices When using this product, observe the danger , caution, and attention notices that are contained in this guide. The notices ar e accompanied by symbols that represent the severity of the safety condition. The sections that follow define each type of safety notice and give examples.
Laser Safety and Compliance Before using the library , review the following laser safety information. Class I Laser Product The library may contain a laser assembly that complies with the performance standards set by the U.S. Food and Dr ug Administration for a Class I laser product.
Rack Safety The following general safety information should be used for all rack mounted devices. DANGER v Always lower the leveling pads on the rack cabinet.
CAUTION: Removing components from the upper positions in the rack cabinet improves rack stability during relocation. Follow these general guidelines whenever you relocate a populated rack cabinet within a room or building: v Reduce the weight of the rack cabinet by removing equipment starting at the top of the rack cabinet.
Preface This manual contains information and instructions necessary for the installation, operation, and service of the Dell ™ PowerV ault ™ TL2000 T ape Library and TL4000 T ape Library . Related Publications Refer to the following publications for additional information.
xvi Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Chapter 1. Product Description The Dell ™ PowerV ault ™ TL2000 T ape Library (2U library) and the Dell PowerV ault TL4000 T ape Library (4U library) provide compact, high-capacity , low-cost solutions for simple, unattended data backup.
T able 1-1 below contains front panel descriptions for both the 2U library in Figure 1-1 on page 1-1 and the 4U library in Figur e 1-2. T able 1-1. 2U library and 4U library front panel descriptions Number Item Description 1 Power button Pressing this button will power ON the library .
T able 1-1. 2U library and 4U library front panel descriptions (continued) Number Item Description 5 Control keys v UP (+) - The upper left button is used to scroll upwar d through menu items. v DOWN (-) - The lower left button is used to scroll downward thr ough menu items.
T able 1-2. 2U library and 4U library rear panel descriptions Number Item Description 1 Power connector(s) Both libraries requir e a 1 10/220 volt AC power connection. v The 2U library has one power supply . v The 4U library has a minimum of one power supply , but has the capability of adding a redundant power supply .
T able 1-2. 2U library and 4U library rear panel descriptions (continued) Number Item Description 4 Shipping lock and label storage location The shipping lock, which secures the accessor during shipping, and associated label are stor ed on the rear panel of the library for futur e use.
T able 1-3. Internal view description Number Item Description 1 Right cartridge magazine(s) v In a 2U library , the right magazine can hold up to 12 cartridges.
is installed at manufacturing time. Each drive receives a unique serial number and certificate. The T10 application may validate each drive instance by checking the drive’s digital certificate.
Supported Internet Protocols The library supports the following Internet protocols: v IPv4 v IPv6 To learn more about IPv4, visit http://www .iana.org/ .
T able 1-5. Library storage capacity and data transfer rate Characteristic 2U Library Specification 4U Library Specification Maximum storage capacity - Ultrium 4 Data Cartridges v 24 data cartridges v Native: 19.2 TB v Compressed: 38.4 TB (2:1 compression) v 48 data cartridges v Native: 38.
Speed Matching To improve system performance, the Ultrium 3 and Ultrium 4 T ape Drive uses a technique called speed matching to dynamically adjust its native (uncompressed) data rate to the slower data rate of the attached server .
Power Management The Ultrium 3 and Ultrium 4 T ape Drive’s power management function controls the drive’s electronics so that part of the electr onics completely turn OFF when circuit functions ar e not needed for the drive’s operation.
Operation Specifications Library with Ultrium 4 drive(s) 2U Library 4U Library Maximum storage capacity Maximum number of data cartridges: 24 Native: 19.2 TB Compressed: 38.4 TB (2:1 compr ession) Maximum number of data cartridges: 48 Native: 38.4 TB Compressed: 75.
Altitude (operating) 2500 meters (8200 ft.) at 25°C ambient Maximum acoustical noise sound power levels LwAd in bels 6.6/6.8 Humidity Operating 15% to 80% RH non-condensing Storage, without cartridges 10% to 90% RH non-condensing Product Environment The library is designed to operate in a general business environment.
1-14 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Chapter 2. User Interfaces This library has two user interfaces. v Operator Control Panel - located on the fr ont panel of the library v We b User Interface - accessed via a web browser Operator Control Panel The Operator Control Panel operates in two basic modes.
become illuminated. The error code will r emain on the Operator Control Panel until a push button is pressed, which will cause the Operator Contr ol Panel to return to the Home Scr een. v Numeric error codes ar e only used for unrecoverable, fatal errors, otherwise text status messages are displayed.
v The Clean LED will only be lit when a cleaning REQUIRED has been issued by the drive. The LED will be turned OFF after a successful drive cleaning operation. v The Attention LED will indicate one of the following conditions. Problem Action Required Bad media 1.
T oggling V alues T oggle values are used to switch between two differ ent states like ON and OFF . 1. After navigating to the menu item, press the SELECT button to select the menu item. 2. Using the UP and DOWN buttons, select one of the various predefined states for that item.
Login Important: Some options of the We b User Interface take the library OFFLINE. This inactive mode can interfere with host-based application softwar e, causing data loss. Make sure the library is idle befor e attempting to perform any remote operations that will take the library OFFLINE.
System Status The System Status screen is always pr esent after login giving current status of the library . Status icons indicate the following conditions. v The green check mark indicates that the library is fully operational and that no user intervention is requir ed.
v If Auto Clean is enabled and a cleaning cartridge is not present, or if a cleaning cartridge is present, but not in a r eserved slot, Auto Clean status will show Chk Media/Rsvd Slot? and Status will show a green check mark and the wor ds Media Attention .
2-8 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Chapter 3. Installation Planning Before installing your library , take time to review the following information. Determining the Number of Logical Libraries Yo u can partition the library into as many logical libraries as there are drives in the library .
Using Multiple Logical Libraries for Library Sharing Multiple logical libraries are an ef fective way for the library to simultaneously back up and restor e data from heterogeneous applications.
Library Partitioning and Element Addressing Library 4U systems with firmware versions of .80 and higher , and containing at least 2 drives, have the ability to configure two logical libraries (cr eate two partitions). This partitioning has been expanded with the new library firmware and half-high drive integration.
Configuration of a 2 Partition System A two partition system must have at least two drives installed. One drive must be installed in either drive position 1 or drive position 2, and another drive must be installed in either drive position 3 or drive position 4.
Configuration of a 4 Partition System A four partition system must have four drives. Each partition will contain one drive and one magazine. SCSI Element Addressing Every logical library starts at the first drive slot with the current assigned element start address (default value 256).
exception in case of a “removed” condition. A drive slot which does not contain a drive and has a position between used slots needs to be reported as a SCSI element. To signal the host application that this slot is not usable, its ACCESS bit will be disabled.
Note: For maximum performance, it is recommended to have a maximum of one drive per SCSI bus. – Only use the maximum system-to-device cable length of 25 m (82 ft) when attaching directly to one device (a point to point inter connection). Physical Characteristics of the SCSI Interface The library operates as a set of SCSI-3 devices.
The Medium Changer device is requir ed to be addressed via LUN 1 of the lowest-numbered drive position of each logical library . The Medium Changer device may additionally be addressed via LUN 1 of other drives in any logical library . Any bus containing a Medium Changer device via LUN 1 of a drive is referr ed to as a control and data path.
v LN Port: (default setting) - an automatic configuration that tries arbitrated loop first, then switched fabric v L Port - arbitrated loop v N Port - point to point protocol in a switched fabric topology Cables and Speeds Ultrium 3 and Ultrium 4 Fibre Channel tape drives use LC duplex fiber optics cables.
zoning capability to form a SAN partition. For systems that do not cooperate, use zoning to prevent the systems fr om sharing the same drive. Yo u can remove zoned partitions as you upgrade software and system levels.
Chapter 4. Installation and Configuration Note: Review the information in ″ Installation Planning ″ before installing your library . To install a desktop or rack mounted 2U library or 4U library , perform the procedur es in this chapter in the order they are pr esented.
T able 4-1. Location criteria (continued) Criteria Definition Clearance v Back: Minimum of 15.4 cm (6 inches) v Front: Minimum of 30.8 cm (12 inches) v Sides: Minimum of 5.08 cm (2 inches) Rack requir ements Standard 19-inch rack with: v 2U (63.5 mm/3.
– Bar code labels – Foot pads (for desktop installation) v W ith every library containing a SCSI drive: – SCSI terminator (one per SCSI drive) – SCSI library-to-host cable (if order ed by cust.
4. Carefully r eturn the library to an upright position. Important: Do not place any objects on top of the library . Removing and Storing the Shipping Lock Important: The shipping lock, which prevents the library accessor fr om moving during shipment, must be removed before the library is powered ON .
2. Store the lock ( 1 ) and label ( 2 ) on the rear panel of the library as shown in Figure 4-5 on page 4-6. 1 2 a77ug018 Figure 4-3. Shipping lock and label a77ug195 Figure 4-4.
Rackmounting the Library (for Rack Installation ONL Y) Attention: If you haven’t removed the shipping lock, complete this first befor e rackmounting your library . See “Removing and Storing the Shipping Lock” on page 4-4. The 2U library and the 4U library are easily installed into a standar d 19-inch rack system.
1. V erify that your rack kit includes the following contents (see Figure 4-6): v Packaged in plastic material: – 2 rails (not shown) – 2 mounting brackets ( 1 ) v Packaged in the small bag .
1 Tw o EIA units for round hole and square hole installation 3 W ide Gaps within the EIA unit 2 4 Narrow Gaps between EIA units 3.
4. Using the T orx wrench included in your shipment, remove the scr ews ( 1 ) as shown in Figure 4-10. Scr ew locations on the 4U library are similar . 5. Install the library rack anchors ( 2 ) as shown in Figure 4-1 1 on each side of your library using the longer counter-sunk scr ews included in the rack kit.
additional short, counter-sunk scr ew included in the rack kit. (The 4U rack anchors and mounting brackets are similar .) 7. W ith library rack anchors and mounting brackets installed, slide the library onto the rails (as shown in Figure 4-12 and Figur e 4-13).
a77ug178 1 Figure 4-14. Securing the 2U library to the rack a77ug175 1 Figure 4-15. Securing the 4U library to the rack Chapter 4. Installation and Configuration 4-1 1.
Connecting the Host Interface Cable To connect the host interface cables to the library: 1. It is recommended that you shut down and turn OFF the associated server . T urn OFF all attached devices. Remove the power cables from the server and all attached accessories.
and limit cable length. If there ar e any SE devices on the same SCSI bus, the entire SCSI bus will negotiate down to SE speed and sever ely degrade performance. v For a Fibre Channel library , connect the host interface cable to the host or to a switch.
5. T urn ON the library using the power button. Check the Operator Control Panel display to make sure the library is r eceiving power . If it is not, check the power connections and your power source. During the Power -On Self T est (POST), all four LEDs are illuminated briefly , followed by a flashing Ready LED.
Using Factory Defaults as Y our Configuration The table below shows the main default library settings. If you wish to use the defaults, no other changes need to be made before using your library Item .
system is serviced by DHCP (Dynamic Host Configuration Protocol) server , the network parameters will be automatically set. Once remote access has been established, you can complete the configuration of your library . 1. Access the Configure menu using the Operator Contr ol Panel.
10. Press the CANCEL button until the Home scr een displays. 11 . Press the CANCEL button to return to the home scr een. 12. Power cycle the library to initialize your configuration. Logging on to the Web User Interface To complete the configuration of your library using the We b User Interface, follow the steps below .
a. Enter in your internet browser addr ess field and press Enter on your keyboard. b. Compare the firmwar e level available on the web to those that you made note of in step 1. If you are r unning the latest levels of library and drive firmware, pr oceed to the next step.
v I/O Station Enabled - If checked, the I/O Station is enabled. If not, the first 3 slots (in a 4U library or the 1st slot in a 2U library) are configur ed as storage.
3. If your library has more than one drive, pr oceed to “Choosing the Number of Logical Libraries for Y our Library.” If your library has one drive, proceed to “Entering Path Failover Feature Activation Key” on page 4-21.
2. Select the number of logical libraries you would like to create in your library . 3. Click Submit to create the logical libraries. Entering Path Failover Feature Activation Key The Path Failover feature is available for select LT O 4 tape drives. Path Failover is not supported for half height drives.
Prer equisites for Library Managed Encryption: v SAS and Fibre Channel LT O Ultrium 4 T ape Drive (Full Height or Half Height) Note: Fibre Channel is full height drive only .
backup and recovery . These settings are requir ed for Library Managed Encryption only . Enter the EKM Server Setting information. v Primary IP address (IPv4 or IPv6) : Enter the IP address of the primary EKM server . v Primary TCP port : After entering the Primary IP address, the library will automatically set the value of the Primary TCP port.
Entering Library Network Settings This page shows the current network configuration of the library and allows modification to the configuration. When a change is requested, a pop-up box will ask to confirm the changes. 1. Click Network in the left navigation pane, to display the Network page.
a. DHCP Address - Click this item ON to have the IP Address of your library automatically set by the library host computer . Leave unchecked and enter the appropriate information for the IP Addr ess, Network Mask, and Gateway Address. b. IP Address - An identifier for a computer or device on a TCP/IP network.
Entering User Access Information using the Web User Interface This function, other than the Access PIN, is not available on the Operator Control Panel. 1. Click User Access in the left navigation pane. 2. Choose a Role. v User v Superuser v Admin v Service Note: Only one password can be set for each Role.
2. Enter the current T ime using the HH:MM:SS 24-hour format. 3. Enter the current Date using the MMDDYYYY format. 4. Click one of the following: v Refresh - to update the current scr een v Submit - t.
2. If you would like to be notified when an error occurs, select Notify Errors . 3. If you would like to be notified when a warning occurs, select Notify W arnings . 4. In To Email Address , enter the email addr ess to which the information will be sent.
Setting the Operator Control Panel Access PIN using the Operator Control Panel 1. Navigate to Configure → Set Access PIN . 2. Press the SELECT button to highlight the first digit of the 4-digit Access PIN. 3. Use the UP and DOWN buttons to select each digit.
For more information on verifying the connection of SCSI devices, see the operating system documentation. Cartridge Magazines The library has removable magazines. Magazine access is passwor d protected. For safety reasons, the accessor motion is stopped when a magazine is r emoved.
2U Library I/O Station The I/O (Input/Output) Station (see Figure 4-35) in a 2U library is part of the left magazine. To open the I/O Station, select Control → Open I/O Station . The I/O Station will pop open. To close the I/O Station, gently push it back into the left magazine.
4U Library I/O Station The I/O Station in a 4U library (see Figure 4-38) is part of the lower left magazine. To open the I/O Station, select Control → Open I/O Station . The I/O Station will pop open. To close the I/O Station, gently push it back into the lower left magazine.
Populating the Library with Data Cartridges For information on working with the cartridge magazines, see “Cartridge Magazines” on page 4-30. 1. Unlock the cartridge magazines.
Inserting the Cleaning Cartridge See the Note below for 4U libraries with a Dedicated Cleaning Slot (DCS). The following criteria must be followed for Auto Clean to function: 1. The Auto Clean function must be configured ″ On ″ or ″ Enabled ″ .
cleaned, the user must manually refr esh the screen after the clean has completed in order to be able to select an additional drive to be cleaned. Chapter 4.
4-36 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Chapter 5. Operations The following table lists menu navigation shortcuts to activities that can be performed via the Operator Control Panel and/or the We b User Interface. Before using the Operator Contr ol Panel or the We b user Interface, please review the information in Chapter 3: User Interfaces .
T able 5-1. Menu navigation shortcuts (continued) Information/ Activity Menu Navigation Shortcuts Operator Control Panel For More Info We b User Interface For More Info Cartridge in drive (n), serial .
T able 5-1. Menu navigation shortcuts (continued) Information/ Activity Menu Navigation Shortcuts Operator Control Panel For More Info We b User Interface For More Info Diagnostics, run drive POST Ser.
T able 5-1. Menu navigation shortcuts (continued) Information/ Activity Menu Navigation Shortcuts Operator Control Panel For More Info We b User Interface For More Info Drive, data compression ON/OFF Not available with this interface.
T able 5-1. Menu navigation shortcuts (continued) Information/ Activity Menu Navigation Shortcuts Operator Control Panel For More Info We b User Interface For More Info Encryption, testing configuration(if feature is available) Not available with this interface.
T able 5-1. Menu navigation shortcuts (continued) Information/ Activity Menu Navigation Shortcuts Operator Control Panel For More Info We b User Interface For More Info Firmware, library , update Not available with this interface.
T able 5-1. Menu navigation shortcuts (continued) Information/ Activity Menu Navigation Shortcuts Operator Control Panel For More Info We b User Interface For More Info Logs, library , view Monitor .
T able 5-1. Menu navigation shortcuts (continued) Information/ Activity Menu Navigation Shortcuts Operator Control Panel For More Info We b User Interface For More Info SCSI Inquiry string, library Mo.
Operator Control Panel Navigation The four control keys on the fr ont of a 2U or 4U library enable the user to navigate through the library settings and make changes as needed to configur e the library . T able 5-2. Library Control Keys Control Keys Description 1 UP (+) - Upper left button Used to scroll upwar d through menu items.
T able 5-2. Library Control Keys (continued) Control Keys Description 3 SELECT - Lower right button Used to display a sub-menu or force an accessor action. 4 DOWN (-) - Lower left button Used to scroll downwar d through menu items. 1. Press the UP ( 1 ) or DOWN( 4 ) keys to enter Interaction Mode.
Monitor Menu The Monitor menu contains information about the following sub menu items: v Library v Drive v Inventory Monitor: Library This menu item displays current library information and settings.
Under Monitor → Library are the following items: v Status v Identity v Error Log v Network Under Monitor → Library → Status are the following items: v Status - current status of the library Error Log Network Identity Monitor Status Status Act. Cart.
v Act. Cart - the serial number of the cartridge currently active in the library v On T ime - the amount of time the library has been powered ON v Slots Empty - the number of empty slots in the librar.
Under Status and Drive (n) are the following items: v Status - the current status of the drive v Activity - the current action being performed by the drive Monitor Status Identity Drive (n) Drive (n) .
v Source - the serial number of the cartridge curr ently in the drive v Cooling - indicates whether or not the drive fan is running v T opology - the topology chosen for a fibre library (see “Fibre .
Under Magazine choose one of the following to see a graphical repr esentation of the cartridge magazine(s). Slots containing cartridges will be highlighted.
Control: Move Cartridges Use this menu item to move cartridges in the library . To move a cartridge from point A to point B, you must make the following choices: v Source T ype - Drive, I/O station, magazine. Only the source type(s) that contain cartridges will be listed.
Choose ″ Left ″ or ″ Right ″ to unlock the corresponding cartridge magazine(s). The magazines can now be removed fr om the library by gently pulling each magazine out of the library . To replace a magazine, insert the back of the magazine into the front of the library and gently push the magazine into the library .
Note: This menu is only available on libraries with multiple drives. Note: Whenever there is a har dware configuration change such as drives being swapped with differ ent form factors (i.e. HH to FH or FH to HH), a library configuration change is needed.
Configure: Library The following library configuration items are in this menu: v Mode : – Random : In random mode, the library allows the server ’s (host’s) application software to select any data cartridge in any or der .
– Sequential : In sequential mode, the library’s firmware pr edefines the selection of the cartridges. After initialization, the firmware causes the library to select the first available cartridge found (counting from the I/O Station through slot 23) for loading into the drive.
For Auto Clean to function, the following criteria must be met: – On 4U libraries with library firmware of .80 or lower that still contain a Dedicated Cleaning Slot (DCS), or 4U libraries with library firmware higher than 1.95 that chose to retain the DCS in their library , a CLN cartridge must be present in that slot.
The following items are in this menu: v Drive Interface - use this to assign a SCSI ID to a SCSI drive or to assign a Port Speed, Port T ype, and Loop ID to a Fibre Channel drive. SAS drives do not requir e user configuration. For more information on drive interfaces, refer to “Host Interfaces” on page 3-6.
– We b Interface (IPv6 Only and Dual Stack): Monitor Library → Library Identity v DHCP - (Dynamic Host Configuration Protocol) If this is enabled, your library host will negotiate the connection with the library . If DHCP is disabled, the following information is necessary to establish the remote access.
changed from a LT O full height to half height configuration in or der for the library to operate properly . If just adding a new drive to the configuration the restore factory default is not requir ed - only a power cycle of the library . T able 5-3.
Configure: Path Failover Use this menu item to enter the Path Failover Feature Activation key (4U library only). The Path Failover feature is available for select LT O 4 tape drives.
1. When prompted by the Operator Contr ol Panel display and the I/O Station opens, insert a blank or scratch data cartridge. 2. Close the I/O Station by pushing it back into the library . 3. While the test is running, the Operator Contr ol Panel will display library status.
The following drive diagnostics and service procedur es are available in this menu: v Clean Drive - The accessor takes the cleaning cartridge from the dedicated cleaning cartridge slot (DCS), or previously r eserved slot if no DCS is available, and inserts it into the drive.
Service: Display Contrast The following display contrast settings are available in this menu: v The numbers 1 through 10 will display , with 10 being the lightest shade and 1 being the brightest. Service: T elnet Service Port The T elnet Service Port menu item is to be used under the direction of the Dell Support Center .
T able 5-4. Web User Interface Menus (continued) Clean Drive Advanced Diagnostics (for Service Personnel only) V iew Logs V iew Drive Logs Save Drive Dump Perform Diagnostics Key Path Diagnostics (if feature is available) Upgrade Firmware Reboot Monitor Library Menu The Monitor Library menu contains the following sub-menu items.
Monitor Library: Drive Identity This page provides the following detailed information about the drive. No changes can be made from this page. The displayed information will vary depending on the library model and drive type (SCSI, SAS, or Fibre Channel).
T able 5-6. Drive Identity page elements (continued) Menu Item Description 2U Library 4U Library SCSI Fibre SAS SCSI Fibre SAS Control Path Drive If the drive communicates all messages from the host to the library , then it is considered the control path drive.
Monitor Library: Library Status This page displays the dynamic information about the library , such as the current status of the components. No changes can be made from this page. T able 5-7 lists all available elements on the Library Identity page. An ″ X ″ indicates that the element displays for the specified library type.
T able 5-7. Library Status page elements (continued) Menu Item Description 2U 4U 1. Right Magazine This displays whether the lower right magazine is ″ Present ″ or ″ Not Present ″ . X 2. Left Magazine This displays whether the upper left magazine is ″ Present ″ or ″ Not Present ″ .
T able 5-8. Drive Status page elements (continued) Menu Item Description 2U Library 4U Library SCSI Fibre SAS SCSI Fibre SAS Port A Status This indicates whether Port A is logged on or out. X X X X Port Name This is the name assigned to Port A on the drive.
T erm Definitions : v BOP (Beginning of Partition) : BOP (Beginning of Partition) is a SCSI term, which in a single partition format is the same as beginning of tape. It means that policy is determined on writes at LB zero. Appending to a tape [or overwriting at a non-zero LB] does not change the policy alr eady in use for that tape.
Monitor Library: Inventory This page provides detailed information about the tape inventory in the library . A summary of each magazine is shown. To get detailed information about the cartridges that reside in a magazine, click on the + button. This will expand the display for the magazine.
Configure Library Menu The Configure Library menu contains the following sub-menu items: v “Configure Library: General” v “Configure Library: Logical Libraries” on page 5-40 v “Configure Lib.
you of the impact of the proposed change. In some cases a pop-up scr een will ask for confirmation. Many changes will also requir e a library reboot. T able 5-9. Configure Library: General page elements Menu Item Description 2U 4U Library Name This is a name that is assigned to your library for ease of identification.
Configure Library: Logical Libraries To partition your multi-drive library , select the number of logical libraries you would like to create in your library , then click Submit .
After clicking Activate , this page will display if you have entered the featur e key correctly . Note: Follow the instructions in the Dell PowerV ault TL4000 Failover Configuration Guide to configure your envir onment for failover . Configure Library: Encryption Note: Application Managed Encryption (AME) does not requir e a key .
5. On the Encryption screen, enter the Feature Activation Key to make available the library managed encryption options. 6. Click Activate to save the key and expand the screen for additional encryption settings. 7. Select Enable SSL for EKM to enable Secure Sockets Layer for the Dell Encryption Key Manager application.
v Internal Label - Encrypt All : Check your tape backup software application documentation to see if this feature is supported. 10. A primary and secondary EKM server can be set for each logical library . Each partition has its own Encryption and EKM settings.
T able 5-1 1. Drive Identity page elements (continued) Menu Item Description 2U Library 4U Library SCSI Fibre SAS SCSI Fibre SAS Speed For each Fibre Channel drive, click on the dr op down list and select Automatic, 1Gb/s, 2Gb/s, or 4 Gb/s. Selecting Automatic will allow library speed to automatically negotiate to the current server speed.
2. Select a Protocol Stack - Choose IPv4 only , IPv6 only , or Dual Stack IPv4 & IPv6 . Note: When changes are made, the following W arning message will appear when the Submit button is clicked. The library must be rebooted or the changes will not take place.
address written as four numbers separated by periods. Each number can be zero to 255. For example, 1.160.10.240 could be an IP addr ess. c. Network Mask - This address defines and limits users within a local network. d. Gateway Address - This address allows access outside the local network.
The following elements are displayed on the User Access page. Role The name associated with the chosen Access Level. New Password The password must be a maximum of ten characters (A-Z, a-z, 0-9, @, <space>, <hyphen>, <period>). Repeat Password Enter the New Password again.
Configure Library: Logs & T races This page allows service personnel to set the error log mode to Of f , Continuous , or to Stop trace at first error . It is recommended that you select Continuous for the Error Log Mode so that all information for logs and traces will be captured.
Note: The TL2000/TL400 email address field cannot be empty (clear). The email notification setup allows the user to turn off the featur e by deselecting the notify error and notify warnings boxes. The user can add an invalid email as long as the email address format is corr ect (i.
Element In the Source screen, this identifies the library element that contains a cartridge. In the Destination screen, this identifies the library element that is empty and can receive a cartridge. V olume Serial In the Source screen, this element displays the serial number of the cartridge.
Advanced Diagnostics (for Service Personnel Only) This menu is for use by Service Personnel only . View Logs This page allows the user to view the library logs after entering the following: v Log T yp.
Save Drive Dump This menu item allows a drive dump to be saved to the host computer . Once the Save Drive Dump button is clicked, the user will have the option of saving the drive dump to their hard drive. The pr ogress status for the drive dump is shown on the System Status screen to the right of the main We b User Interface screen.
for each test cycle requested. When completing the “Slot To Slot” test, you will need to Inventory your library before placing it back online, since this test scrambles the cartridge slot locations. The user selects the number of test cycles before starting the test fr om the EXECUTE button.
Each test will show a result of “Passed” or “Failed”. T est results will clear: v When the test is rer un v When the library is rebooted The time and date of the last test will appear below the Key Path Diagnostics screen. If any of the tests fail, r efer to “Maintenance Problems” on page 7-2 for additional information.
Service Library: Reboot Important: Some options of the We b User Interface take the library OFFLINE. This inactive mode can interfere with host-based application softwar e, causing data loss. Ensure that the library is idle befor e attempting to perform any remote operations that will take the library OFFLINE.
3. Close the door of the I/O Station. The library will automatically start an inventory . The cartridges in the I/O Station will be counted but unassigned until they are moved into storage slots. 4. Go to Main → Control → Move Cartridges and move the data cartridges into the desired data slots.
Configuring I/O Stations and Reserving Slots 2U libraries usually have 1 slot for an I/O Station, while 4U libraries have 3 slots assigned as an I/O Station. These slots can be configured as storage if needed. To configure the I/O Station using the We b User Interface, follow these steps.
5-58 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Chapter 6. Using Ultrium Media Figure 6-1 shows the LT O Ultrium 800 GB Data Cartridge and its components. 1 LT O cartridge memory 4 W rite-protect Switch 2 Cartridge door 5 La.
T ype Native Data Capacity Recording Format Ultrium 3 400 GB (800 GB at 2:1 compression) Reads and writes data on 704 tracks, sixteen tracks at a time Ultrium 2 200 GB (400 GB at 2:1 compression) Read.
WORM Media Because standard r ead/write media are incompatible with the WORM feature, a specially formatted WORM tape cartridge (see Figure 6-2) is r equired. Each WORM cartridge has a unique, worldwide cartridge identifier (WWCID), which comprises the unique CM chip serial number and the unique tape media serial number .
Note: The drive will automatically eject an expired cleaning cartridge. The Cleaning Cartridges are valid for 50 uses. L T04 drives cannot be cleaned with an L T01 cleaning tape.
Guidelines for Using Bar Code Labels Apply the following guidelines whenever using bar code labels: v Do not reuse a label or r eapply a used label over an existing label. v Before you apply a new label, r emove the old label by slowly pulling it at a right angle to the cartridge case.
to become a scratch (blank) data cartridge. Do not write-protect scratch (blank) cartridges; the tape drive will not be able to write new data to them. If you must manually set the write-protect switch, slide it left or right to the desired position. Handling the Cartridges Attention: Do not insert a damaged tape cartridge into the drive.
v Never ship a cartridge in a commercial shipping envelope. Always place it in a box or package. v If you ship the cartridge in a cardboar d box or a box of a sturdy material, ensure the following: – Place the cartridge in polyethylene plastic wrap or bags to protect it fr om dust, moisture, and other contaminants.
v Inspect the rear of the cartridge (the part that loads first into the tape load compartment) and ensure that ther e are no gaps in the seam of the cartridge case. If there ar e gaps in the seam (see Figure 6-6), the leader pin may be dislodged. v Check that the leader pin is properly seated.
The best storage container for the cartridges (until they are opened) is the original shipping container . The plastic wrapping prevents dirt from accumulating on the cartridges and partially protects them fr om humidity changes.
6-10 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Chapter 7. T roubleshooting Installation Problems Problems encounter ed during the installation of the library are usually caused by improper SCSI bus configuration, application softwar e configuration errors, or an incorrectly configur ed operating system.
Ensure that SAS Cables ar e properly attached. Refer to “Connecting the Host Interface Cable” on page 4-12. v Backup Application Installation: Refer to the documentation included with your backup application software for instructions on how to verify pr oper installation.
T able 7-1. T roubleshooting table (continued) Problem Solution Library does not power ON 1. Perform “Isolating a Power Supply Problem” on page 7-8. The Operator Control Panel is blank or frozen 1. If possible, log on to the We b User Interface and check the error log.
T able 7-1. T roubleshooting table (continued) Problem Solution Connection problem with the Dell Encryption Key Manager (EKM) If you are using library-managed encryption, perform the Key Path Diagnostic (see “Service Library: Perform Key Path Diagnostics” on page 5-53) if this feature is available.
Attention LED Drive Sled Issues: Whenever there is a har dware configuration change such as drives being swapped with differ ent form factors (i.e. HH to FH or FH to HH), a library configuration change is needed. Reconfiguring the library by reassigning the amount of logical libraries will clear this issue.
Cartridge placement problems Magazine slot prism fiducials NOT seated pr operly can result in gripper or slider error codes due to the fiducial interfering with the back edge of the cartridge. Release and pull magazines out of the library for inspection.
T ape library performance: The library is not efficiently backing up data 1. Check the network bandwidth from the host computer . If you are backing up data over a network, consider comparing to a local-only backup.
code reader and positional emitter pulse count after the prism detection r etry count is exhausted. If several prisms are missing or damaged or if the accessor prism sensor/emitter is inoperable, initialization and/or inventory functions can take a prolonged amount of time to complete due to the lengthy r etry recovery procedur e.
T able 7-2. Power Supply LED Meanings 1 If the blue LED is lit, AC voltage is available. 2 If the amber LED is lit, there is a possible fan pr oblem or other power supply issue. The power supply will need replacement. 3 If the green LED is lit, DC power is OK and active.
4. For power supplies with LED’s, if the “Amber” LED is lit, replace the power supply (refer to “Replacing a Power Supply” on page 10-7). 5. If your power supply has no LED’s, and you have.
Operator Control Panel Service Menu and clean the drive. Use only an approved cleaning cartridge (see “Cleaning Cartridge” on page 6-3). 7. Run the Library V erify Diagnostic which includes a drive performance Read/W rite test (other drive diagnostics are also available) available on the Operator Control Panel or We b User Interface.
4. If the ethernet connection is a direct connection between the PC and the library , a special ″ crossover ″ ethernet cable needs to be used. Note: On newer PCs, either straight through or cr ossover ethernet cables may be used since the crossover r equirement is provided internally .
1. Navigate to Move Cartridges using the Operator Control Panel ( Control → Move Cartridges ). 2. Select Source . 3. Scroll thr ough the different slots containing cartridges, and look for an exclamation point ( ! ). The exclamation point indicates that the cartridge is bad or was rejected due to wr ong format, write protected, etc.
7-14 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Chapter 8. Error Codes If an error occurs during operation of the library , the library stops the current operation and displays an error code on the LCD scr een. Unless otherwise noted in T able 8-1 on page 8-2, try to resolve the error by cycling power to the library and retrying the last operation.
T able 8-1. Error Codes Error Code Description User Action 30 SCSI: transport element full Check the application software. 31 SCSI: all slots empty 32 SCSI: invalid opcode 33 SCSI: invalid element add.
T able 8-1. Error Codes (continued) Error Code Description User Action 50 SCSI: cartridge belongs to another partition Check application software. 54 SCSI: failure in LME interface 55 SCSI: invalid license key entered 58 Recovered Err or: SCSI parity error Command successful after retries.
T able 8-1. Error Codes (continued) Error Code Description User Action 89 Gripper blocked 1. If this is the first time the library has been powered ON or if it has been moved to a new location, ensure that the shipping lock has been removed.
T able 8-1. Error Codes (continued) Error Code Description User Action 8E Cannot find gripper block within the expected range 1. Run the Library V erify T est, then retry the operation.
T able 8-1. Error Codes (continued) Error Code Description User Action B3 Accessor controller ur gent stop due to a released magazine 1. V erify that the left and right magazines are completely inserted, then retry operation. 2. If the problem still exists, contact technical support.
T able 8-1. Error Codes (continued) Error Code Description User Action DC I 2 C Bus Failure Contact technical support. DD Power Supply x fan has failed, Redundancy may be at risk The subcode indicates.
T able 8-1. Error Codes (continued) Error Code Description User Action F3 Drive Hardwar e Error The subcode indicates which drive is affected. Example: Subcode 02: drive #2 Contact technical support. F4 Drive Load T imeout Drive has run in a timeout while loading a tape.
T able 8-2. Sub error codes (continued) 0B Error first sled init, move to sensor failed 0C Error during sled movement to r otation position 0D Error during r otation to drive position 0E Error slider .
T able 8-2. Sub error codes (continued) 36 Error during sled movement in FLMoveSled function 37 Error during sled positioning to sensor in FLMoveSled function 38 Error during sled positioning to mail .
T able 8-2. Sub error codes (continued) 94 Sled movement to home sensor position failed. 95 Sled movement to transport position failed. A0 Movement of I/O slot failed. A1 Sled movement to sensor failed. A2 Sled movement to rotation position failed. A3 Elevator movement to home position failed.
8-12 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Chapter 9. Service Procedures Removing Cartridges from Magazine Slots In the event of a severe mechanical pr oblem with the library or if circumstances requir e you to remove tape cartridges, do the following. If the Operator Control Panel or the We b User Interface is still operational: 1.
a77ug025 Figure 9-1. Access holes for the left magazine 9-2 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
3. To manually release the magazines, push the end of a straightened paper clip into the access hole for each magazine at the back of the library . While holding the paper clip, have a second person pull the magazine out of the front of the unit. DO NOT push the paper clip in more than 1/2 inch.
4. If there ar e additional tapes still in the library , or if you were unable to manually remove the magazines and drive, contact technical support for further instructions. a77ug191 Figure 9-3. Left Magazines pulled out of the 2U library a77ug186 Figure 9-4.
Using the ITDT Firmware Update, Dump Retrieval and Drive T est T ool A newly designed tool, ITDT , has multiple functional capability and is a very quick, convenient and efficient method for drive firmwar e updates. As a note, drive dump retrievals can be performed by the tool as well.
9-6 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Chapter 10. Check, Adjust, Remove, and Replace T ools Required To service a library you may need one or more of the following tools: v #2 Phillips screwdriver v Ground strap (r ecommended, if available) Electrostatic Discharge Important: A discharge of static electricity can damage static-sensitive devices or microcir cuitry .
6. Insert the shipping lock ( 1 ) into the slot located on the center of the top of the library and secure with the shipping label ( 2 ). 7. Pack the library in its original packaging materials (or equivalent packaging) for moving or shipping.
Replacing a T ape Drive Sled There ar e two types of drive sleds in a TL2000 library (2U library) and a TL4000 library (4U library). The contents of the ship groups ar e specific to the type of drive sled.
T ape drive sleds are installed at the back of the library . 1. Power OFF the library before r emoving and/or installing a SCSI drive sled. Fibre Channel and SAS drive sleds ar e hot pluggable and may be removed and installed while the library is powered ON.
2 SAS cable 3 SCSI terminator 4 Fibre Channel cable 5 Ethernet cable 6 Power cords 7 Drive sled blue captive thumbscrews 8 Black pull-out tab 9 Drive sled 10 Drive sled handle 4. If present, r emove the conductive tape from the drive sled (refer to Figur e 10-8 on page 10-7).
Important: Push in on the drive sled handle ( 10 in Figure 10-5 on page 10-4) while supporting the bottom of the drive sled until it is properly seated. Damage to the connector pins may occur if this procedur e is not followed. 10. Push the drive sled slowly into the drive slot until the sled seats itself against the back of the library .
Note: The small gray markers show where conductive tape should be placed to provide ESD pr otection. 13. Push the black tab ( 8 in Figure 10-5 on page 10-4) back underneath the library . When inserted properly , only the handle of the tab will be visible.
3. Loosen the three blue captive thumbscr ews on the power supply located on the back panel of the library . 4. Pull on two of the thumbscrews to pull the unit away fr om the rear panel of the library , then grasp the top and bottom edge of the power supply and pull it out of the library .
screen entitled “VPD Selection”, wher e it is asking you to determine which copy of VPD should be written to the new Library Controller Car d. If the message ″ VPD Selection ″ is displayed at .
Note: Use care when selecting the appr opriate VPD to restore fr om/to. An error in selection her e could cause a long downtime. 13. Package the failed Library Controller Car d in the same packaging in which the new control boar d was shipped to you and return to Dell.
4. If the defective library is rack mounted, remove the two scr ews ( 1 in Figure 10-12) fr om the front of the defective library anchoring the mounting brackets on the library to the rack. W ith assistance, remove the defective library from the rack.
Unpacking and Preparing the Replacement Library Enclosure Before installing the r eplacement library enclosure, it is important to verify that the enclosure is functioning pr operly . 1. Unpack the replacement library enclosur e and place it on a sturdy and clean work surface near the defective library .
3. Carefully r eturn the library to an upright position. 4. Remove the shipping lock from the top of the r eplacement library enclosure (see Figure 10-14 on page 10-14). 1 a77ug085 Figure 10-13. Foot pads installed on the bottom of the library enclosure Chapter 10.
5. Store the lock and label on the back panel of the r eplacement library enclosure (see Figure 10-15). 6. Proceed to “Swapping Library Contr oller Cards” on page 10-15. Note: Do not power on the replacement library enclosur e without first swapping the library controller car ds.
Swapping Library Controller Cards IMPOR T ANT - READ ME BEFORE CONTINUING The Library Enclosure contains a copy of the vital pr oduct data (VPD) for your library . The VPD contains your current library configuration. A primary copy of this VPD is contained within the Library Contr oller Card.
2. Power ON the replacement library enclosur e. a. If power ON is successful: 1) The replacement library enclosur e will power up with the Ready/Activity LED ( 1 in Figure 10-17 on page 10-17) 2.
T able 10-1. 1 Ready/Activity LED (green) 3 Attention LED (amber) 2 Clean Drive LED (amber) 4 Error LED (amber) Installing Y our Drive(s) in the Replacement Library Enclosure N.
a. On the rear of the defective library , loosen the blue captive thumbscrews on the drive. b. If necessary , remove the conductive tape fr om the drive sled.
Note: The gray markers show where conductive tape should be placed. j. Push the black tab back underneath the drive sled. When inserted properly , only the handle of the tab will be visible.
a77ug025 Figure 10-20. Access hole for the left magazine (facing rear of library) 10-20 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
b. Push the end of a straightened paper clip into the access hole for each magazine at the back of the library . DO NOT push the paper clip in more than ½ inch. While holding the paper clip, have a second person pull the magazine out of the front of the unit.
2. Insert the cartridge magazines removed fr om the defective library into the same positions in the replacement library enclosur e. 3. Insert the cartridge magazines removed fr om the replacement library enclosure into the same positions in the defective library to return to Dell.
3) Grasp the top and bottom edges of the power supply and pull it out of the library . b. Install the power supply removed fr om the defective library in the replacement library enclosur e. Install the power supply removed from the replacement library enclosur e in the defective library to return to Dell.
Rack Installation: 1. Remove the mounting brackets ( 1 in Figure 10-24) and anchors ( 2 ) fr om each side of the defective library and install them on the replacement library enclosure. 2. W ith assistance, slide the replacement library enclosur e onto the metal rails that are alr eady in position in the rack (see Figure 10-25).
Completing the Installation of the Replacement Library Enclosure 1. Connect the following cables to the replacement library enclosur e. (See Figure 10-1 1 on page 10-1 1). a. Power cord ( 6 ) b. Host interface cable ( 1 , 2 , and/or 4 ) c.
10-26 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Appendix A. SCSI Element T ypes and Addresses For an overview of library partitioning and element addressing, see “Library Partitioning and Element Addressing” on page A-2. The following tables contain element addresses for the 2U library and the 4U library .
4U Library I/O Slots, Storage Slots, and Drive Slots Element Addresses and Physical Locations For an overview of library partitioning and element addressing, see “Library Partitioning and Element Addressing.
the status of logical library 1 in the main menu due to space limitations. The user must navigate to the logical libraries status in the OCP to get the information on the additional library partitions.
Configuration of a 2 Partition System A two partition system must have at least two drives installed. One drive must be installed in either drive position 1 or drive position 2, and another drive must be installed in either drive position 3 or drive position 4.
SCSI Element Addressing Every logical library starts at the first drive slot with the current assigned element start address (default value 256). It will be incr emented from the bottom to the top slots for every drive slot. There is one exception to this addr essing scheme to accommodate libraries currently in the field.
A-6 Dell PowerV ault TL2000 T ape Library and TL4000 Ta p e Library User's Guide.
Appendix B. T apeAlert Flags This appendix is intended to provide additional information to the r eader about the tape drive. All error code and diagnostic information contained in this chapter can be accessed from the Operator Contr ol Panel of the Library.
13d Library Pick Retry W There is a potential pr oblem with the cartridge loader picking a cartridge from a drive or slot. v No action needs to be taken at this time. v If the problem persists, This flag is cleared when the next move command is r eceived.
T apeAlert Flags Supported by the Drive T able B-1. T apeAlert Flags Supported by the Ultrium T ape Drive Flag Number Flag Description Action Required 3 Hard err or Set for any unrecoverable r ead, write, or positioning error . (This flag is set in conjunction with flags 4, 5, or 6.
T able B-1. T apeAlert Flags Supported by the Ultrium T ape Drive (continued) Flag Number Flag Description Action Required 18 T ape directory corrupted in the cartridge memory Set when the drive detects that the tape directory in the cartridge memory has been corrupted.
T able B-1. T apeAlert Flags Supported by the Ultrium T ape Drive (continued) Flag Number Flag Description Action Required 53 T ape system area r ead failure Set when the tape system area could not be read successfully at load time. Copy the data to another tape cartridge, then discard the old cartridge.
B-6 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Appendix C. Sense Data When a drive encounters an error , it makes sense data available. Yo u can use device drivers to examine the sense data and determine errors. . The device drivers may conflict with some commercial softwar e applications unless properly configured.
T able C-1. Library Sense Keys, ASC and ASCQ (continued) Sense Key ASC ASCQ Description Medium Error (03) 30h 00h Incompatible media installed 30h 03h Cleaning tape installed 30h 07h Cleaning failure .
T able C-1. Library Sense Keys, ASC and ASCQ (continued) Sense Key ASC ASCQ Description Hardwar e Error (04) 81h 80h Cannot initialize bar code r eader 81h 81h No response fr om bar code reader 81h 82.
T able C-1. Library Sense Keys, ASC and ASCQ (continued) Sense Key ASC ASCQ Description Hardwar e Error (04) (continued) 81h B0h Slave robotic contr oller response timeout 81h B1h NACK received fr om .
T able C-1. Library Sense Keys, ASC and ASCQ (continued) Sense Key ASC ASCQ Description Illegal Request (05h) 1Ah 00h Parameter length error 20h 00h Invalid command operation code 21h 01h Invalid elem.
T able C-1. Library Sense Keys, ASC and ASCQ (continued) Sense Key ASC ASCQ Description Command Aborted (0Bh) 3Fh 0Fh ECHO buffer overwritten 43h 00h SCSI message error 47h 00h SCSI parity error 49h 0.
T able C-2. LT O T ape Drive Sense Data (continued) Byte Bit Address or Name 7 6 5 4 3 2 1 0 12-13 Additional Sense Code (ASC) Additional Sense Code Qualifier (ASCQ) Byte 12 Byte 13 ASC ASCQ 00 00 - N.
T able C-2. LT O T ape Drive Sense Data (continued) Byte Bit Address or Name 7 6 5 4 3 2 1 0 12-13 Additional Sense Code (ASC) - Additional Sense Code Qualifier (ASCQ) (Continued) Byte 12 Byte 13 ASC .
T able C-2. LT O T ape Drive Sense Data (continued) Byte Bit Address or Name 7 6 5 4 3 2 1 0 12-13 Additional Sense Code (ASC) - Additional Sense Code Qualifier (ASCQ) (Continued) Byte 12 Byte 13 ASC .
T able C-2. LT O T ape Drive Sense Data (continued) Byte Bit Address or Name 7 6 5 4 3 2 1 0 12-13 Additional Sense Code (ASC) - Additional Sense Code Qualifier (ASCQ) (Continued) Byte 12 Byte 13 ASC .
T able C-2. LT O T ape Drive Sense Data (continued) Byte Bit Address or Name 7 6 5 4 3 2 1 0 12-13 Sense Key 6 (Unit Attention) EE 12 - Encryption - Key Change Detected EE 18 - Encryption - Changed (R.
T able C-2. LT O T ape Drive Sense Data (continued) Byte Bit Address or Name 7 6 5 4 3 2 1 0 36-39 Port Identifier (Relative T arget Port Addr ess) Reporting Sense (This is the port address of the drive port through which sense is being r eported.
T able C-2. LT O T ape Drive Sense Data (continued) Byte Bit Address or Name 7 6 5 4 3 2 1 0 65 Last Error FSC 66 67 Last Error Flag Data 68 69 LPOS Region 70-85 ERP Summary Information 86-89 Product .
means that the current dir ection is away from the physical beginning of the tape. A 1 means that the current dir ection is towards the physical beginning of the tape. 12. Relative LPOS fields (Bytes 30-33) reports the curr ent physical position on the tape.
Appendix D. Enabling LUN Support in Linux To verify the detection of a tape drive, administrators should check for its entry in /proc/scsi/scsi . Current versions of Linux may not scan the logical storage unit (LUN) ID of every device. This can result in some PowerV ault devices not being identified or listed in the /proc/scsi/scsi output.
Red Hat Enterprise Linux RHEL doesn’t automatically probe all LUNs on SCSI devices. The symptom shows LUN 0, which would be the drive, but not the loader . 1. T ype #cat /proc/scsi/scsi . Attached devices: Host: scsi0 Channel: 00 Id: 06 Lun: 00 Vendor: CERTANCE Model: ULTRIUM 2 Rev: 1826 Type: Sequential-Access ANSI SCSI revision: 03 2.
5. Add the /LUNS switch to the load line of the appropriate SCSI driver . If a dual channel card is installed and the user is unsur e which channel the LUN device is attached to, simply edit both lines. LOAD ADPT160M.HAM SLOT=201 /LUNS LOAD ADPT160M.HAM SLOT=202 /LUNS 6.
D-4 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Appendix E. Notes on IPv6 Compatibility with Windows 2003/XP and 2008/V ista IPv6 addressing is dif ferent from traditional IPv4 addr essing. IPv4 addressing is listed in the format 255.
v After upgrading the W inInet API (by upgrading to IE 7), the library RMU can be accessed from the br owser by using the following format. – Replace all : with - .
Appendix F. Library Configuration Form Use this form when planning your library configuration. Keep this document in a secure location and update it when changes ar e made to the library configuration.
SAS Drive settings Logical Library: Position: ID: Logical Library: Position: ID: Logical Library: Position: ID: Logical Library: Position: ID: SCSI Drive settings Logical Library: Position: ID: Logica.
Notices T rademarks T rademarks used in this text: Dell, the Dell logo, and PowerV ault are trademarks of Dell Inc. Microsoft and W indows are register ed trademarks of Microsoft Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
G-2 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Glossary This glossary defines the special terms, abbreviations, and acr onyms that are used in this publication. Numbers 2:1 compression. The relationship between the quantity of data that can be stored with compr ession as compared to the quantity of data that can be stor ed without compression.
beginning of tape. It means that policy is determined on writes at LB (logical block) zero (the first block in the partition). Appending to a tape [or overwriting at a non-zero LB] does not change the policy alr eady in use for that tape. Border Gateway Protocol (BGP).
affects host r eporting of density and is included to support legacy needs for transparency . The default of not masking encrypted densities means that the host can see a differ ent density code for encrypted vs non-encrypted tapes (x72 [enc] as opposed to x52 [non-enc]).
ESD. Electrostatic dischar ge. ESP . The Encapsulating Security Payload (ESP) protocol pr ovides origin authenticity , integrity , and confidentiality protection of a packet. ESP also supports encryption-only and authentication-only configurations, but using encryption without authentication is strongly discouraged because it is insecure.
IML. Initial micropr ogram load. Incomp. Mag.. Incompatible Magazine: This message appears on the Operator Control Panel during library initializing. It occurs during factory restor e or VPD. This is not a real issue since it takes the library a while to configure.
loadable. Having the ability to be loaded. LME. Library Managed Encryption LT O cartridge memory (L TO-CM). W ithin each LT O Ultrium data cartridge, an embedded electronics and interface module that can store and r etrieve a cartridge’s historical usage and other information.
wound solenoid that is excited with a linear current density in its winding of one abampere per 4 π centimeters of axial length. offline. Pertaining to the operation of a functional unit without the continual control of a computer . Contrast with online .
SE. Single-ended. Secure Sockets Layer . See SSL . segment. A part. sel. Select. Serial Attached SCSI (SAS). A drive sled with a SAS interface can be linked directly to contr ollers.
T elnet. See T elnet Service Port . T elnet Service Port. A network protocol used by service personnel, under direction by support personnel, to access the library . TELNET clients are used, often when diagnosing problems, to manually ″ talk ″ to other services without specialized client software.
H-10 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
Index A Access PIN, Operator Control Panel 4-29 accessor 1-6 Accessor 1-5 accessory package 4-2 active slots 5-20, 5-38 Active Slots 4-18 air quality 4-1 air vents, front panel 1-1 Application Managed.
L Labels bar code 6-4 guidelines for using 6-5 LED, amber 7-12 LEDs 2-2, 7-8 LEDs, front panel 1-1 library configuration form F-1 Library Controller Boar d 1-5 library firmware, curr ent level 5-30 li.
We b User Interface (continued) Configure Library: Restor e Defaults 5-49 configuring library 4-15 date and time 4-26 drive information 4-23 event notification 4-27 general library information 4-18 lo.
X-4 Dell PowerV ault TL2000 Ta p e Library and TL4000 Ta p e Library User's Guide.
.
Printed in USA.
デバイスDell TL2000の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Dell TL2000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDell TL2000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dell TL2000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dell TL2000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dell TL2000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDell TL2000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dell TL2000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDell TL2000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
