Deltaメーカー(Model 31-300)の使用説明書/サービス説明書
ページ先へ移動 of 24
INSTRUCTION MANUAL P ART NO. 913131 - 04-12-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury .
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage.
5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SPECIFIC SAFETY RULES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions.
6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug.
7 3. 240 VOL T SINGLE PHASE OPERA TION The motor supplied with your saw is a dual voltage, 120/240 volt motor . It is set at the factory at 120 volts. If it is desired to operate your machine at 240 volts, single phase, it is necessary to reconnect the motor leads in the motor junction box by following instructions given on the motor nameplate.
8 FOREWORD Delta Model 31-300 is an industrial/commercial duty 1-1/2 HP belt/disc sander . The induction-type, ball-bearing motor provides long-lasting, smooth performance. The Sanding Center can provide 3000 SFPM with the belt, and the disc will r evolve at 2100 RPM.
9 Fig. 5 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose).
10 A TT ACHING MACHINE TO ST AND DISCONNECT MACHINE FROM POWER SOURCE. 1. Pull the belt (A) Fig. 8 down through the smaller rectangular hole (B) in the top shelf of the stand. 2. Fasten the machine to the top shelf with four 5/16" x 1/2" bolts and lockwashers (C) Fig.
11 A B C Fig. 9 Fig. 10 Fig. 11 DISCONNECT MACHINE FROM POWER SOURCE. 1. Thread the disc table trunnion stud (A) Fig. 12 into the hole (B) on the side of the machine and tighten snug. 2. Place the disc table trunnion clamp (C) on the stud and insert the two pins (D) in the two holes (E).
Fig. 18 A ST AR TING AND STOPPING THE MACHINE The on-off switch (A) Fig. 16 is located on the sander base. T o tur n the sander “ON”, move the switch to the up position. T o tu rn the sander “OFF”, move the switch to the down position. Fig. 16 Fig.
13 ADJUSTING TENSION AND TRACKING OF THE BEL T The machine is shipped without belt tension. Before operating the machine, follow these instructions for adjusting the belt for tension and tracking. 1. Loosen the two lock knobs (A) Fig. 19, and remove the top cover (B).
14 14 After a long period of time, adjustments may be necessary to maintain the tension and tracking of the sanding belt. If the belt will not hold its tension, tighten the set screw (G) Fig. 22. If the belt will not hold its tracking, tighten the set screw (F) Fig.
15 CHANGING POSITION OF SANDING ARM DISCONNECT MACHINE FROM POWER SOURCE. 1. The sanding arm (A) can be used in the vertical position (Fig. 31), the horizontal position (Fig. 30), or any angle in between. Loosen the lock handle (B), position the arm (A) to the desired angle, and tighten the lock handle (B).
16 16 DISCONNECT MACHINE FROM POWER SOURCE Fig. 33 Fig. 32 ADJUSTING SANDING DISC T ABLE 90 DEGREES TO DISC TIL TING THE DISC SANDER T ABLE DISCONNECT MACHINE FROM POWER SOURCE. The table (A) can be tilted 45 degrees down (Fig. 34), by loosening the lock handle (B), tilting the table (A), and tightening lock handle (B).
17 REPLACING SANDING BEL T T o replace the sanding belt: 1. Loosen the two lock knobs (A) Fig. 38, and remove the top cover (B). 2. Loosen the two screws (C) Fig. 39 enough to allow the back panel (D) Fig. 38 to hinge open. NOTE: The scr ew (C) cannot be removed.
18 Fig. 45 Fig. 44 SURF ACING OR EDGE SANDING WITH SANDING BEL T When surfacing (Fig. 44) or edge sanding (Fig. 45), place the sanding arm in the horizontal position and use the table (A) Fig. 44 and Fig. 45 to keep the workpiece in place. Hold the workpiece firmly and keep your fingers away from the sanding belt.
19 Fig. 48 END SANDING WITH THE DISC When sanding the ends of narrow workpieces, use the sanding disc and an accessory miter gauge (A) Fig. 48. Move the work from the center to the left side (downwar d) of the sanding disc. AL WA YS SAND ON THE LEFT SIDE (DOWNWARD ROT A TION SIDE) OF THE SANDING DISC.
20 20 TROUBLESHOOTING For assistance with your machine, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).
21 A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier .
22 NOTES.
23 NOTES.
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
デバイスDelta (Model 31-300)の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Delta (Model 31-300)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta (Model 31-300)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta (Model 31-300)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta (Model 31-300)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta (Model 31-300)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta (Model 31-300)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta (Model 31-300)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta (Model 31-300)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。