Deltaメーカー22-540の使用説明書/サービス説明書
ページ先へ移動 of 17
INSTRUCTION MANUAL 12 Portable Planer (Model 22-540) P ART NO. 901606 (013) Copyright © 2001 Delta Machinery ESP AÑOL: PÁGINA 17 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
3 ADDITIONAL SAFETY RULES FOR PLANERS 1. DO NOT operate the tool until it is completely assembled and installed according to the instructions. 2. IF YOU ARE NOT thoroughly familiar with the operation of planers, obtain advice from your supervisor , instructor or other qualified person.
4 CONNECTING TOOL TO POWER SOURCE POWER CONNECTIONS A separate electrical circuit should be used for your tools. This cir cuit should not be less than #12 wir e and should be protected with a 20 Amp time lag fuse.
Use proper extension cor ds. Make sur e your extension cord is in good condition and is a 3-wir e extension cor d which has a 3-prong gr ounding type plug and a 3-hole r eceptacle which will accept the tool’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the curr ent of the saw .
6 UNP ACKING AND CLEANING Carefully unpack the tool and all loose items fr om the shipping container(s). Peel pr otective film from the table surface. Remove and clean the protective coating fr om the cutterhead. Remove the pr otective coating from all unpainted surfaces.
7 ASSEMBL Y INSTRUCTIONS Fig. 4 Fig. 5 Fig. 6 ASSEMBLING RAISING AND LOWERING HANDLE 1. Assemble raising and lowering handle (A) Fig. 4, to shaft (B) and fasten in place with screw (C). NOTE: Make certain the flats of the handle and flat on shaft are aligned with each other .
8 Fig. 7 Fig. 8 Fig. 9 ASSEMBLING CHIP DEFLECTOR 1. Assemble chip deflector (A) Fig. 7, to the planer by inserting end of chip deflector over the top of the cutterhead. Make certain the two screws, one of which is shown at (B) are inserted upwar d thr ough the two slots (C) in the chip deflector .
9 OPERA TING CONTROLS AND ADJUSTMENTS Fig. 13 Fig. 14 Fig. 15 Fig. 16 ST AR TING AND STOPPING PLANER The “ON/OFF” switch (A) Fig. 13, is located on the front of the planer motor . T o turn the machine “ON”, move the switch toggle (B) to the up position.
Fig. 17 Fig. 18 Fig. 19 Fig. 20 LEVELING EXTENSION T ABLES For optimum performance, the extension tables, one of which is shown at (A) Fig. 17, must be level with the planer table. T o check the extension tables and adjust if necessary , pr oceed as follows: 1.
11 5. If an adjustment to one or both knives is necessary , slightly loosen the seven locking screws, six of which ar e shown at (C) Fig. 21, by turning the screws CLOCKWISE into the knife locking bar just enough to r elieve stress in the cutterhead and not disturb the knife setting.
Fig. 23 LIFTING STRAPS Y our planer is provided with two lifting straps (A) Fig. 23, located on the top of the planer , for ease in transporting the planer . OPERA TIONS When using your machine, you may want to follow these few simple steps for achieving the best results possible.
13 MAINTENANCE Fig. 26 Fig. 27 Fig. 28 Fig. 30 Fig. 29 BRUSH INSPECTION AND REPLACEMENT CAUTION: BEFORE INSPECTING THE BRUSHES, DIS- CONNECT THE TOOL FROM THE POWER SOURCE. Brush life varies. It depends on the load on the motor . Check the brushes after the first 50 hours of use for a new machine or after a new set of brushes has been installed.
Delta Building T rades and Home Shop Machinery T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which.
15 NOTES.
16 NOTES.
The following are trademarks of POR TER-CABLE DEL T A Corporation (Las siguientes son marcas registradas de POR TER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC ® , .
デバイスDelta 22-540の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Delta 22-540をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta 22-540の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta 22-540の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta 22-540で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta 22-540を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta 22-540の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta 22-540に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta 22-540デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
