Deltaメーカー31の使用説明書/サービス説明書
ページ先へ移動 of 16
INSTRUCTION MANUAL 6" Belt and 12" Disc Abrasive Finishing Machine (Model 31-731) P ART NO. 420-01-651-0013 - 05-28-03 Copyright © 2003 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .
2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
3 1. FOR YOUR OWN SAFETY , READ THE INSTRUC- TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT .
4 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SAFETY RULES FOR ABRASIVE FINISHING MACHINES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions.
5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug.
6 Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
7 FOREWORD Delta Model 31-731 is a abrasive finishing machine. The Delta Model 31-731 includes two tilting tables, 4½" arbor pulley , V -belt, 80-grit aluminum oxide belt and 50-grit aluminum oxide disc. FUNCTIONAL DESCRIPTION UNP ACKING AND CLEANING YOUR MACHINE IS SHIPPED WITHOUT BEL T TENSION APPLIED TO THE SANDING BEL T .
8 ALIGNING PULLEYS, ASSEMBLING BEL T AND ADJUSTING BEL T TENSION DISCONNECT MACHINE FROM POWER SOURCE Using a straight edge (A) Fig. 6, make certain the motor pulley (B) is aligned with the arbor pulley .
9 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPPING THE ABRASIVE FINISHING MACHINE T o start the machine, push “ON” button (A) Fig. 10. T o stop the machine, push “OFF” button (B).
10 3. Loosen tracking lock knob (D) Fig. 14, and while rotating the belt (F) by hand, as shown, tighten or loosen tracking knob (E) until the belt is running true on the pulleys. 4. Then jog the machine on and off to check further if the belt is tracking properly .
11 ADJUSTING POSITION OF SANDING ARM DISCONNECT MACHINE FROM POWER SOURCE. The sanding arm can be positioned in the vertical or horizontal position, or at any desired angle in between as follows: 1. Loosen two bolts (A) Fig. 18, move the sanding arm to the desired position, and tighten the two bolts.
12 ADJUSTING T ABLE SQUARE WITH SANDING DISC DISCONNECT MACHINE FROM POWER SOURCE. 1. Place an accurate square (C) Fig. 23, on the table with one end of the square against the disc. 2. Loosen the table locking knobs (A) Fig. 23, which are located on each end of the table and move the table until it is at 90 degrees to the disc.
13 ADJUSTING THE PLA TEN The platen (A) Fig. 24, is set at the factory 1/32 of an inch higher than the crown of the drums (B). This allows the belt, when properly tensioned, to lay flat on the platen and eliminate stretching and bulging which might occur if the platen is not at the right height.
14 NOTES.
15 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations.
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.
デバイスDelta 31の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Delta 31をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta 31の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta 31の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta 31で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta 31を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta 31の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta 31に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta 31デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。