Deltaメーカー31-390の使用説明書/サービス説明書
ページ先へ移動 of 16
INSTRUCTION MANUAL 6" Edge Sander (Model 31-390, 391, 392) P ART NO. 406-11-651-0006 - 03-12-02 Copyright © 2002 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
ADDITIONAL SAFETY RULES FOR ABRASIVE FINISHING MACHINES 1 . DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instructions. 2. OBT AIN ADVICE from your supervisor, instructor , or another qualified person if you are not familiar with the operation of this machine.
4 POWER CONNECTIONS A separate electrical circuit should be used for your tools. This cir cuit should not be less than #12 wir e and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wir e extension cords which have 3- prong gr ounding type plugs and matching r eceptacle which will accept the tool’ s plug.
Fig. A FUNCTIONAL DESCRIPTION FOREWORD Delta Model 31-390 is a lar ge capacity Edge Sander for fast, efficient, straight and bevel edge sanding with the added ability to handle contour sanding jobs.
6 ASSEMBLING LEGS TO EDGE SANDER Carefully assemble the two support legs to the base of the edge sander as follows: 1. Fasten each support leg (C) Fig. 3, to the base of the machine (A) with five 3/8-16 x 1" hex head screws, ten flat flatwashers, five lockwashers and hex nuts, (D) Fig.
ASSEMBLING BEL T TENSION LEVER Assemble the belt tension lever (A) Fig. 7, to the tensioning mechanism by threading the end of lever (B) into the tapped hole (C) and tighten lock nut. ASSEMBLING TOP GUARD AND DUST CHUTE ASSEMBL Y T wo dust chutes (A) Fig.
ASSEMBLING AUXILIAR Y ABRASIVE DRUM AND SPINDLE ASSEMBL Y TO DRIVE PULLEY The auxiliary abrasive drum and spindle assembly is furnished as standard equipment with the edge sander and is used for finish sanding of small contour workpieces.
ASSEMBLING AUXILIAR Y END T ABLE ASSEMBL Y The auxiliary end table is furnished as standard equip- ment with the edge sander . The table is used when performing contour sanding operations around the drive pulley and auxiliary abrasive drum and spindle assembly .
ST AR TING AND STOPPING EDGE SANDER T o start the tool, push the start button (A) Fig. 25; to stop the tool, push stop button (B). ADJUSTING T ABLE POSITION T o raise or lower the straight table, loosen lock knobs (A) Fig. 26, adjust table height and tighten knobs (A).
ADJUSTING LONG PLA TEN T o adjust the long platen when sanding on the straight table: 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Remove the top guard and dust chute assembly . 3. Loosen two hex nuts (A) Fig.29 holding brackets (B) at each end of the machine, and move platen (C) in or out as needed.
ADJUSTING BEL T TRACKING T o check and adjust the tracking of the sanding belt on the pulleys, proceed as follows: 1. Raise the dust chutes (A) Fig. 34, at both ends of the top guard and dust chute assembly . 2. Make certain the top guard and dust chute assembly is not interfering with the rotation of the sanding belt.
EDGE SANDING When edge sanding, it is advisable to raise one end of the table as shown in Fig. 36. This allows cooler belt running, prevents spot wear , reduces material burning and promotes longer belt life. The table should be positioned so it is close to, but not contacting the sanding belt.
CHANGING SANDING BEL TS T o remove and install sanding belts, proceed as follows: 1. DISCONNECT TOOL FROM POWER SOURCE. 2. The sanding belt can be changed with or without the top guard and dust chute r emoved fr om the machine. 3. Push in on belt tension lever (A) Fig.
15 T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in.
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG .
デバイスDelta 31-390の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Delta 31-390をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta 31-390の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta 31-390の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta 31-390で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta 31-390を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta 31-390の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta 31-390に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta 31-390デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。