Deltaメーカー31-552の使用説明書/サービス説明書
ページ先へ移動 of 12
INSTRUCTION MANUAL 6" Abrasive Belt Finishing Machine (Model 31-552) P ART NO. 406-03-651-0017 (0110) Copyright © 2001 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
ADDITIONAL SAFETY RULES FOR ABRASIVE BEL T FINISHING MACHINES 3 WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed accor ding to the instructions.
4 POWER CONNECTIONS IMPORT ANT : Make sure the electrical characteristics ar e the same between the motor nameplate and the power source and make sur e the power cir cuit the machine will be used on is properly fused and that wir e size is corr ect. IN ALL CASES, MAKE SURE THE RECEPT ACLE IN QUESTION IS PROPERL Y GROUNDED.
5 Use proper extension cor ds. Make sur e your extension cord is in good condition and is a 3-wir e extension cor d which has a 3-prong gr ounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the curr ent of the machine.
6 ASSEMBL Y ST AND AND ELECTRICALS If you purchased your machine with the optional steel stand and electricals, the stand is shipped as shown in Fig. 2. The switch (A) Fig. 2 and motor (B) Fig. 3 are completely assembled to the stand and the necessary wiring from the motor to the switch has been completed.
7 ALIGNING PULLEYS, ASSEMBLING BEL T AND ADJUSTING BEL T TENSION DISCONNECT MACHINE FROM POWER SOURCE Using a straight edge (A) Fig. 6, make certain the motor pulley (B) is aligned with the arbor pulley .
8 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPPING THE ABRASIVE FINISHING MACHINE T o start the machine, push “ON” button (A) Fig. 10. T o stop the machine, push “OFF” button (B).
9 ADJUSTING T ABLE DISCONNECT MACHINE FROM POWER SOURCE. T o tilt the table, loosen the table tilting handle (A) Fig. 15, move the table to the desired angle, and tighten the table tilting handle. The table tilting handle can be reposition- ed by pulling out the handle and repositioning it on the hex nut located underneath the handle.
10 INST ALLING OR REMOVING ABRASIVE BEL T Y our machine uses a 6"x48" belt. T o install or remove the belt, proceed as follows: DISCONNECT MACHINE FROM POWER SOURCE. 1. Remove the idler drum guard (A) and side guar d (B) Fig. 20. 2. T ur n the belt tension handle counter clockwise to reduce belt tension to a minimum.
11 ABRASIVE BEL TS - THEIR SELECTION AND USE Delta supplies a wide range of belts for use on your Finishing Machine. These belts are r ecommended for a wide range of work on wood, metals, plastics and other materials.
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG .
デバイスDelta 31-552の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Delta 31-552をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta 31-552の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta 31-552の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta 31-552で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta 31-552を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta 31-552の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta 31-552に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta 31-552デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。