Deltaメーカー4000の使用説明書/サービス説明書
ページ先へ移動 of 20
METAL DETECTOR O WNER’S MANUAL If you do not have prior experience with a metal detector , we strongly recommend that you: 1) Adjust the Sensitivity to a low setting in the event of false signals. Always begin use at a reduced sensitivity level; this device is designed to work “into-the-noise”, so expect chatter at high sensitivity .
2 T ABLE OF CONTENT S T erminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5 Batteries . . . . . . . . .
TERMINOLOG Y The following terms are used throughout the manual, and are standard terminology among detectorists. ELIMINA TION Reference to a metal being "eliminated" means that the detector will not emit a tone, nor light up an indicator , when a specified object passes through the coil’s detection field.
4 ASSEMBL Y Assembly is easy and requires no tools. ● 1 Loosen both Locking Collars by rotating 100% counterclockwise ● 2 Insert the Upper Stem into the S-Rod and click Silver Button into hole ● 3 Position the lower stem with the silver button toward the back.
5 ASSEMBL Y Adjusting the Arm Rest The arm rest may be moved forward or backwards by removing the single screw and nut, and then repositioning the 2-piece arm rest. Users with shorter arms may find the arm rest more comfortable in the forward position.
6 The detector requires a single 9-volt ALKALINE battery (battery not included). Do not use ordinary zinc carbon batteries. Rechargeable batteries can also be used. If you wish to use rechargeable batteries, we recommend using a Nickel Metal Hydride rechargeable battery .
7 QUICK-S T ART DEM ONSTRA TION I. Supplies Needed • a Nail • a Zinc Penny (dated after 1982) • a Nickel • a Quarter II. Position the Detector a. Place the detector on a table, with the searchcoil hanging over the edge. Or better , have a friend hold the detector , with the searchcoil of f the ground.
8 THE BASICS OF MET AL DETEC TING A hobby metal detector is intended for locating buried metal objects. When searching for metals, underground or on the surface, you have the following challenges and objectives: 1. Ignoring signals caused by ground minerals.
4. Size and Depth of Buried Objects When using the detector in the motion DISCRIMINA TION mode, the relative depth of an object is displayed on the right of the display in a 5-segment format. A more accurate depth reading is available in a no-motion mode, using PINPOINT mode.
10 OPERA TION and CONTROLS HOW TO WORK THE CONTROLS Press MENU button to select the menu item you want to adjust. Press MODE button to TOGGLE between the Discrimination and All-Metals modes. POWER ON/OFF Press and hold the Pinpoint button to actuate PINPOINT at any time.
11 OPERA TION and CONTROLS cont. MENU SELECTIONS 1. SENSITIVITY Use and to increase or decrease sensitivity while the SENSITIVITY line is highlighted. Maximum sensitivity setting is 12. Minimum sensitivity setting is 4. If the detector beeps erratically or beeps when there are no metal objects being detected, reduce the sensitivity .
OPERA TION and CONTROLS cont. MENU SELECTIONS continued 2. DISC. LEVEL Use and to increase or decrease DISCRIMINA TION level. Each time you press , a target category is eliminated from detection.
13 At any time, the display screen indicates the current category notches or discrim- ination settings. Any category whose description is not visible will not be detected. For example, the following settings tell us that: • The nickel, dime, quarter and 50¢ categories will be detected.
14 OPERA TION and CONTROLS cont. MODE SELECTIONS There are three selections under the MODE section of the display . • Press to toggle between DISCRIMINA TION and ALL MET ALS.
15 3. PINPOINT Enter PINPOINT from either Disc or All Metals mode. Press and hold to activate pinpoint. Pinpoint detection is only active for as long as you keep depressed. Pinpoint is used to find the exact location of a target which was previously located and identified using the discrimination mode.
16 T ARGET IDENTIFICA TION In DISCRIMINA TION mode, targets are identified both audibly and visually as follows: 1. Different pitch tones for dif ferent types of metals 2.
17 2-Digit T arget Identification The 2-digit value in the middle of the screen provides a specific target value to help identify buried targets more accurately . With practice in the field, you will learn to associate target values with specific objects.
18 READING THE DISPLA Y The Liquid Crystal Display (LCD) shows the PROBABLE identification of the targeted metal, as well as the PROBABLE depth of the target. The detector will register a consistent target identification, upon each sweep of the coil, when a buried target has been located and identified.
TROUBLE SHOOTING GUIDE SYMPT OM CA USE SOLUTION Detector chatters • Using detector • Use detector or beeps erratically indoors outdoors only • Using detector near • Move away power lines from .
O WNER’S MANUAL If you do not have prior experience with a metal detector , we strongly recommend that you: 1) Adjust the Sensitivity to a low setting in the event of false signals. Always begin use at a reduced sensitivity level; this device is designed to work “into-the-noise”, so expect chatter at high sensitivity .
デバイスDelta 4000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Delta 4000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta 4000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta 4000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta 4000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta 4000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta 4000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta 4000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta 4000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。