Deltaメーカー50-861の使用説明書/サービス説明書
ページ先へ移動 of 16
INSTRUCTION MANUAL 5 H.P . Dust Collector (Model 50-866 Single Phase) (Model 50-861 Thr ee Phase) P ART NO. 902110 - 04-18-02 Copyright © 2002 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the product. Using the machine with r espect and caution will considerably lessen the possibility of personal injury .
3 IMPOR T ANT SAFETY RULES FOR DUST COLLECTORS W ARNING: Basic precautions should always be followed when using your dust collector . T o reduce the risk of injury , electrical shock or fire, comply with the safety rules listed below: 1. DO NOT leave the dust collector plugged into the electrical outlet.
4 UNP ACKING AND CLEANING Carefully unpack the tool and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened wi th ke r osene (do not use acetone, gasoline or lacquer thinner for this purpose).
5 Fig. 3 Fig. 4 1. Motor , Fan and Blower Assembly (Hardwar e for mounting not shown: 5/16" flat washer (4), 5/16" lockwasher (4), 5/16-18 hex nut (4) 2. Drums (2) 3. Gaskets (2) 4. Switch Control Box for Model 50-866 only .( 3 sheet metal screws for mounting) 5.
6 ASSEMBL Y ASSEMBLING CASTERS TO BASE T ur n base over . Align four holes in caster (A) Fig. 5, with four holes at one corner of base (B) and assemble caster to base.
7 Fig. 10 Fig. 11 Fig. 12 Fig. 14 Fig. 13 4. NOTE: FOR MODEL 50-866 MAKE SURE THA T THE FRONT OF THE MOTOR ASSEMBL Y IS A TT ACHED TO THE SUPPORT WITH THREE PREDRILLED HOLES IN IT , (THESE HOLES ARE WHERE THE CONTROL BOX IS TO BE MOUNTED). Carefully place the motor/blower assembly (F) Fig.
8 Fig. 15 Fig. 16 Fig. 17 Fig. 18 9. Fig. 15, illustrates both drums (K) assembled to the fan and blower assembly (F). ASSEMBLING DRUM SUPPOR T POSTS TO BASE AND DRUMS 1. Assemble end of drum support post (A) Fig. 16, to threaded holes in one corner of base (B).
9 Fig. 19 Fig. 20 Fig. 21 Fig. 22 ASSEMBLING INT AKE PORT TO MOTOR AND BLOWER ASSEMBL Y Place the intake port (A) Fig. 19, onto the flange of motor/blower assembly (B). Align the holes in the flange (B) of the motor/blower assembly with the mounting holes in the dust intake port and fasten with four sheet metal screws (C) as shown in Fig.
10 Fig. 23 Fig. 24 Fig. 25 Fig. 26 3. Assemble six-position filter bag hanger assembly (G) Fig. 23, to the top half of the upper bag support (H). Place a 5/16" lockwasher (I) onto a 5/16-18x1¼" hex head screw (J), place a special washer (K) (30mm O.
11 Fig. 27 Fig. 28 Fig. 29 ASSEMBLING DUST COLLECTION BAGS TO DRUMS 1. Insert bag clamp (A) Fig. 27, through the loops of the dust bag (B). 3. Clamp the dust collection bag (B) Fig. 29, around drum (C) with the locking band (F). Assemble the remaining dust collection bag to the drum at the other side of the dust collector .
12 Fig. 32 CONNECTING MACHINE TO POWER SOURCE MODEL 50-866 SINGLE PHASE INST ALLA TION WARNING: Installation by a qualified electrician is recommended to assur e safe and proper wiring and product operation. The motor rating for your single phase dust collector is 230 V olts, 5 H.
13 Fig. 34 Fig. 35 MODEL 50-861 THREE PHASE INST ALLA TION WARNING: Installation by a qualified electrician is recommended to assur e safe and proper wiring and product operation. The motor rating for your three phase dust collector is 200-2 20/440 V olts, 5 H.
14 MAINTENANCE NOTE: Before any maintenance or service is performed, be sur e that unit is disconnected from power sour ce to prevent accidental starting. MOTOR MAINTENANCE Removing dust and dirt: Blow off motor with low pressur e air to remove dust or dirt.
15 ACCESSORIES A complete line of accessories is available from your Delta Supplier , Porter -Cable · Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier .
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG .
デバイスDelta 50-861の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Delta 50-861をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta 50-861の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta 50-861の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta 50-861で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta 50-861を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta 50-861の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta 50-861に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta 50-861デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。