DesaメーカーSDVBPDの使用説明書/サービス説明書
ページ先へ移動 of 42
NA TURAL GAS BURNER SYSTEM MODEL SDVBND PROP ANE/LP GAS BURNER SYSTEM MODEL SDVBPD REMOTE READY FOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch • Do not use any phone in your building.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 2 TABLE OF CONTENTS SAFETY INFORMATION SAFETY INFORMA TION IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this stove and burner system.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 3 3 P I L O T O F F P I L O T O N HI LO IN OUT PRODUCT IDENTIFICA TION Figure 1 - DESA Direct-Vent .
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 4 LOCATION AND SPACE REQUIREMENTS Determine the safest and most efficient location for your cast iron stove. Make sure that rafters and wall studs are not in the way of the venting system.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 5 5 6 " (15.24 cm) 4 " (10.16 c m Front 4" (10.16 cm) from Front Ceiling Floor from Back Wall 29" (73.66 cm) 42" (106.68 cm) 36" (91.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 6 6. Remove all contents from inside stove cavity .
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 7 7 12. Check general catch bolt alignment with door claw . Make fi- nal adjustment and door leveling after stove is in normal stand- ing position. 13.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 8 NOTICE: If installing blower in an existing stove burner system with gas connections, shut off gas supply and disconnect heater from gas supply. Con- tact a qualified service person to do this.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 9 9 CAST IRON STOVE AND DIRECT -VENT BURNER SYSTEM ASSEMBL Y Continued Green Ground Wire Wiring Dia.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 10 GENERAL VENTING Your stove with burner system is approved to be vented either through the side w.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 11 11 Fixed Closed Openable Fixed Closed Openable V V V V V V V V X X V X G G J F B B K N H I A N E.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 12 WARNING: Read all instructions completely and thoroughly before attempting installation. Failure to do so could result in serious injury, property damage or loss of life.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 13 13 INSTALLATION FOR HORIZONTAL TERMINATION Snorkel terminations are available for terminations requiring a vertical rise on the exterior of the building (see Figures 21 and 22).
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 14 3. Attach vent pipe assembly to the burner system. Set stove in front of it’ s permanent location to insure minimum clearances. Mark the wall for a 10"(25.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 15 15 Horizontal Termination Configurations Figures 28 through 30 show different configurations for venting with horizontal termination. Each figure includes a chart with vertical minimum/maximum and horizontal maximum dimensions which must be met.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 16 1. Determine the route your vertical venting will take. If ceiling joists, roof rafters, or other framing will obstruct the venting system, consider an offset (see Figure 31) to avoid cutting load bearing members.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 17 17 Vertical Termination Configurations Figure 35 through 38 show four different configurations for vertical termination.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 18 V enting with T wo 90 ° Elbows V er tical (V 1 ) Horizontal (H) 5' min. 6' max. 6' min. 12' max. 7' min. 18' max. 8' min.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 19 19 VENTING INST ALLA TION Continued HIGH ALTITUDE INSTALLATION Your cast iron stove and direct-vent burner system has been CSA tested and approved for operation at altitudes in the USA from 0- 2000 ft.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 20 CAUTION: Use only new, black iron or steel pipe. Internally-tinned copper tubing may be used in cer- tain areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to burner system.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 21 21 ON POSITION OFF POSITION WARNING: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas. We recommend that you install a sediment trap/drip leg in supply line as shown in Figure 40, page 20.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 22 3. Check all joints from propane/LP supply tank or gas meter to equipment shutoff valve (see Figure 43 for propane/LP or Figure 44 for natural). Apply noncorrosive leak test solution to all gas joints.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 23 23 W R STOVE AND DIRECT -VENT BURNER SYSTEM INST ALLA TION Continued INSTALLING OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1 WARNING: Installation must be done by a qualified installer familiar with low voltage wiring procedures.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 24 4. Place receiver into valve bracket and align holes (see Figure 49). 5. Use push-in fasteners included with receiver to secure to bracket. 6. Connect the wires from the receiver to the valve at TH and THTP (see Figure 45, page 22).
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 25 25 1 2 3 4 It is very important to install these logs exactly as instructed in Figures 54 through 57. Do not modify logs. Only use logs supplied with freestanding burner system.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 26 P I L O T O F F P I L O T O N TPTH TP TH HI LO IN OUT TO TURN OFF GAS TO APPLIANCE 1. T urn ON/OFF switch, located on side of rear cover , to “OFF”.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 27 27 HI LO IN OUT OPTIONAL HAND-HELD REMOTE OPERATION OPERA TING STOVE WITH BURNER SYSTEM Continued Selector Switch in Remote Position (Optional Remote Control) Variable Control Knob Gas Control Knob in On Position MANUAL LIGHTING procedure 1.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 28 Safety Features When away from home for an extended period of time or as a child safety feature to prevent accidental ignition of the fireplace, the receiver ON/OFF/REMOTE switch should be in the OFF position.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 29 29 CLEANING AND MAINTENANCE WARNING: Turn off burner system and let cool before cleaning. CAUTION: You must keep control areas, burners, and circulating air passageways of burner system and stove clean.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 30 TROUBLESHOOTING Note: All troubleshooting items are listed in order of operation. WARNING: Turn off burner system and let cool before servicing. Only a qualified service person should ser- vice and repair burner system or stove.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 31 31 OBSERVED PROBLEM Burner does not light after pilot is lit Delayed ignition burner Burner back.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 32 TROUBLESHOOTING Continued WARNING: If you smell gas • Shut off gas supply. • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 33 33 Figure 65 - Blower Wiring Diagram for Thermostat-Controlled Models WIRING DIAGRAM CAUTION: Label all wires prior to disconnection when servicing controls.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 34 TPTH TP TH TPTH TP TH 4 19 20 21 23 26-1 26-4 26-2 26-3 6 24 4 25 4 1 28 28 4 7 8 9 18 10 11 13 .
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 35 35 P ARTS LIST MODELS SDVBND, SDVBPD This list contains replaceable parts used in your burner system. When ordering parts, follow the instructions listed under Replace- ment Parts on page 33 of this manual.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 36 ILLUSTRA TED P AR TS BREAKDOWN AMITY™ SCIVF(*) AND PSCIVF(*) SERIES VICTOR HEARTH™ VH(*) SER.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 37 37 P ARTS LIST AMITY™ SCIVF(*) SERIES, PSCIVF(*) SERIES VICTOR HEARTH™ VH(*) SERIES OXFORD™ VCIS(*) SERIES, PVCIS(*) SERIES (* Indicates Color Suffix Designation) This list contains replaceable parts used in your stove.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 38 ACCESSORIES Purchase these stove and burner system accessories from your local dealer. If they can not supply these accessories, call DESA’s Sales Department at 1-866-672-6040 for information.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 39 39 1. Where will the product be used? ❍ Living/F amily Room ❍ Office/Warehouse ❍ Utility Shed/Outbuilding ❍ Gar age ❍ Bedroom ❍ Bathroom ❍ Other 2.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 40 2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004 Postage Required T APE T APE.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 41 41 NOTES _______________________________________________________________________________________.
112126-01B For more information, visit www.desatech.com For more information, visit www.desatech.com 42 W ARRANTY INFORMA TION DESA LIMITED WARRANTY DIRECT-VENT BURNER SYSTEM PLUS AMITY ™ AND VICTOR.
デバイスDesa SDVBPDの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Desa SDVBPDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDesa SDVBPDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Desa SDVBPDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Desa SDVBPDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Desa SDVBPDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDesa SDVBPDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Desa SDVBPDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDesa SDVBPDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。