AirLiveメーカーWN-200HDの使用説明書/サービス説明書
ページ先へ移動 of 103
i W N-200HD 2.0 Mega Pixel Wireless 150Mbps IPCamera User’s Manual.
Copyright & Disclaimer i AirLive WN-200HD User’s Manual Copyright & Disclaimer No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recor ding without the written consent of OvisLink Corp.
Copyright & Disclaimer AirLive WN-200HD User’s Manual ii FCC Statement Federal Communication Commission Interf erence Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Table of Contents iii AirLive WN-200HD User’s Manual Table of Contents 1. Introdu ction..................................................................................................... 1 1.1 Over view ........................................
Table of Contents AirLive WN-200HD User’s Manual iv 4.2.2 Wire less ................................................................................ 29 4.2.3 DDN S .............................................................................
1. Introduction 1 AirLive WN-200HD User’s Manual 1 1. Introduction 1.1 Overview This camera is an inexpensive and fully scalable surveillance device. Because the Network Cameras can be plugged into your existing local area network (LAN), you will potentially save thousands of dollars from unnecessary cabling.
1. Introduction AirLive WN-200HD User’s Manual 2 1.2 Features z Easy installation with setup wizard (IP Wizard II) z UPnP device discovery and NAT router transversal for easy installation z Dynamic IP Service, DIPS®, to search your IP camera from Internet easily z H.
1. Introduction 3 AirLive WN-200HD User’s Manual 1.4 Package Contents User can find the following items in the package: z This camera is the main element of the product. z Camera Stand with screws z Detachable WLAN antenna z Power adapter dedicates 12V DC electric power output to Network Camera.
1. Introduction AirLive WN-200HD User’s Manual 4 1. Lens & Focus Ring User could use this ring to adjust focus manually. 2. Microphone The Camera has built-in an internal microphone. This microphone is hidden in the pinhole located on the front panel.
1. Introduction 5 AirLive WN-200HD User’s Manual 3. Antenna User can attach the included antenna to antenna connector (SMA type) or use another high-gain antenna to get higher performance. 4. Factory Default Reset This button is hidden in the pinhole.
1. Introduction AirLive WN-200HD User’s Manual 6 1.6 Hardware Installation 1. Attach the Camera with the included stand 2. Place the Camera on the table or fix it onto ceiling or wall Use three screws to fix the Network Came ra onto the ceiling or wall.
1. Introduction 7 AirLive WN-200HD User’s Manual 3. Plug an Ethernet cable into the Camera Connect an Ethernet cable to the LAN socket located on the Network Camera’s bottom and attach it to the network. 4. Connect the external power supply to Camera Connect the attached power adapter to the DC power jack of the Network Camera.
2. Getting Started AirLive WN-200HD User’s Manual 8 2 2. Getting Started 2.1 IP Wizard Once you have installed the Network Camera well and powered it on, the network accessing type LED will turn on. It means the system is booting up successfully.
2. Getting Started 9 AirLive WN-200HD User’s Manual When launch the IPWizard II, a searchi ng window will pop up. IPWizard II is starting to search Network Cameras on t he LAN.
2. Getting Started AirLive WN-200HD User’s Manual 10 2.1.1 View If IPWizard II finds network devices, View button will be available. Please select the device you want to view and click the View button. Then you could see the video from camera directly.
2. Getting Started 11 AirLive WN-200HD User’s Manual You could modify the relative setti ngs of the selected device. Click “ << ” button will quit the LAN setting procedure and click “ >> ” button will move to next page as below.
2. Getting Started AirLive WN-200HD User’s Manual 12 In case, you do not want to change user name and/or password, then just click “ Submit ” button to perform your se tting accordingly. Click “ << ” button will go back to previous page.
2. Getting Started 13 AirLive WN-200HD User’s Manual 2.1.3 Wireless In case you want to change the IP rela ted parameters of wir eless interface, please select the device you w ant to configure and click the WIRELESS button. Relative settings will be carried out as above.
2. Getting Started AirLive WN-200HD User’s Manual 14 Click SSID to select your wireless AP or router and key in WEP or WPA key. Click >> to next step:.
2. Getting Started 15 AirLive WN-200HD User’s Manual Make sure wireless setting and then submit it. Click OK to confirm these param eters, then IPWizard II will start to configure this camera with specified information.
2. Getting Started AirLive WN-200HD User’s Manual 16 Once this step finished, IPWizard II will prompt you to unplug the Ethernet cable to activate wireless access. Then IPWizard II will prompt you to test wireless setting or finish wireless procedure as below.
2. Getting Started 17 AirLive WN-200HD User’s Manual To discover your device, go to your Desktop and click My Network Places . Click the targeted Device. Then Internet Explorer will connect to this Network Camera automatically. 2.3 Install the IP Camera behind NAT router Once installed, the device is accessible on your LAN.
2. Getting Started AirLive WN-200HD User’s Manual 18 (1) Enable UPnP option of your NAT router To use UPnP IGD function (NAT traver sal), you need to make sure the UPnP function is enabled in your router. Most new home routers should support this function.
2. Getting Started 19 AirLive WN-200HD User’s Manual 2. Type in your login name and password under “USERNAME” and “PASSWORD” textbox. For the first ti me use (default value), input the U.
2. Getting Started AirLive WN-200HD User’s Manual 20 2.4.2 Login as Administrator If you log in the Camera as the Administrator, you can perform all the settings provided by the device. Start-up screen will be as follow no matter an ordinary users or an administrator.
3. Configure the Camera 21 AirLive WN-200HD User’s Manual 3 3. Configure the Camera 3.1 Monitor the Image Section The image shot by the device is shown here. The date and time are displayed at the top of the window. 3.2 View Profile The device supports multi-profile function for H.
3. Configure the Camera AirLive WN-200HD User’s Manual 22 3.6 Full Screen Enlarge video to full screen display. : Enlarge video to full screen disp lay. Press “ESC” key to disable this function. 3.7 Active Control The plug-in ActiveX control supports a lo t of functions by clicking the left mouse button.
3. Configure the Camera 23 AirLive WN-200HD User’s Manual 3.7.1 Digital Zoom Click Digital Zoom to active this function as abov e. User can drag or scale the box over the video to adjust zoom ratio and position.
3. Configure the Camera AirLive WN-200HD User’s Manual 24 Click Snap shot to activate this function. Press Snapshot button to take a picture. The image file is saved as J PEG format into your local PC. Select Browser , the pop-up window to select the save path and file name prefix, select OK to continue.
3. Configure the Camera 25 AirLive WN-200HD User’s Manual stop it, press Stop to stop recording. Select Brow ser , the pop-up window to select the save path and file name prefix, select OK to continue. After stop recording, list the files, this file is named as Video_yyyymmddhhmmss.
3. Configure the Camera AirLive WN-200HD User’s Manual 26 Click About to show this ActiveX information..
4. Monitor the Image Section 27 AirLive WN-200HD User’s Manual 4 4. Monitor the Image Section 4.1 Monitor the Image Section This function is only available for user logged into Camera as administrator . Click on each menu name to display its setting page.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 28 MAC address: Displays the Ethernet MAC address of t he device. Note that user can not change it. Obtain IP address automatically (DHCP): DHCP: Stands for Dynamic Host Configuration Protocol.
4. Monitor the Image Section 29 AirLive WN-200HD User’s Manual Primary DNS and Secondary DNS: If you do not select Obtain DNS from DHCP , then you need to enter these parameters manually. HTTP Port: The device supports two HTTP ports. T he first one is default port 80 and this port is fixed.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 30 Setting (Easy Installation): Provides a 2-step procedure to configure wireless setting: Step 1: Select SSID of wireless r outer or access point (AP).
4. Monitor the Image Section 31 AirLive WN-200HD User’s Manual Step 2: Key in security key of WEP or WPA. Then click “ Submit ” button to activate wireless setting. In case, user wants to c onfigure wireless settings ma nually, please follow the steps as below: MAC address: Displays the Ethernet MAC addr ess of the WLAN card.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 32 Type: To select one of WLAN modes from Infrastructure or Ad -Hoc mode. Security mode: Shows which type of security the netwo rk uses.
4. Monitor the Image Section 33 AirLive WN-200HD User’s Manual WPA settings: - WPA Key: Key value of WPA. The device uses a pre-shared key (PSK) for key management. The pre-shared key can be en tered either as Manual hex, as 64 hexadecimal characters, or as a Passphr ase, using 8 to 63 ASCII characters.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 34 One such service you can use is www. DynDNS.org. You’ll need to register with the service and set up the domain name of your choice to begin using it . Please refer to the home page of the servic e for detailed instruct ions or refer to Appendix G for more information.
4. Monitor the Image Section 35 AirLive WN-200HD User’s Manual DDNSHost: The domain name is applied of this device. User name: The user name is used to log into DDNS.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 36 PPPoE: To enable or disable the PPPoE service here. User name: Type the user name for the PPPoE servic e which is provided by the ISP. Password: Type the password for the PPPoE service which is provided by the ISP.
4. Monitor the Image Section 37 AirLive WN-200HD User’s Manual 4.2.5 Steaming RTSP is a streaming cont rol protocol, and a starting point for negotiating transports such as RTP, multicas t and Unicast, and for negotiating codecs. RTSP can be considered a "remote contro l" for controlling the media stream delivered by a media server.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 38 4.2.6 UPnP UPnP is short for Universal Plug and Play , which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. This device is an UPnP ena bled Network Camera.
4. Monitor the Image Section 39 AirLive WN-200HD User’s Manual Friendly Name: Shows the friendly name of this device here. UPnP NAT Traversal When enabled, the device will attempt to configure port mapping in a NAT router on your network, using UPnP™.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 40 4.2.8 IP Filter You can enter different user’s IP address which are allowing enter or denying by the device. IP Filter: To enable or disable the IP filter function here. IP Filter Policy : Choose the filter policy wher e is denying or allowing.
4. Monitor the Image Section 41 AirLive WN-200HD User’s Manual 4.2.9 IP Notification In case the IP address is changed, system is able to send out an email to alert someone if the function is enabled. SMTP Notification (e-mail): If enable this function, then the “ Send to ” and “ Subject ” fields need to be filled.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 42 TCP Port: Set port number of TCP server. Message: The message will be sent to FTP server. HTTP Notification: If enable this function, then the fields below need to be filled. URL: Type the server name or the IP address of the HTTP server.
4. Monitor the Image Section 43 AirLive WN-200HD User’s Manual Proxy Address: Type the server name or the IP address of the HTTP Proxy. Proxy Port: Set port number of Proxy. Proxy Login name: Type the user name for the HTTP Proxy. Proxy Login Password: Type the password for the HTTP Proxy.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 44 Rotation: Turn the “Mirror” and “Vertical Flip” On or OFF. The im age will be overturned as below. White Balance: Auto: will adjust the white balance automatically. Hold: will hold the white balance.
4. Monitor the Image Section 45 AirLive WN-200HD User’s Manual De-Noise: De-Noise can remove or lower unwanted noise and preserve fine details and edges. Default Settings: Restore to factory image settings. 4.3.2 Privacy Mask Use this page to specify privacy mask window 1 to window 7 and set the name and gray level for selected window.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 46 4.4 System – Configure and Maintain Use this menu to perform the prin cipal settings of the device. 4.4.1 System DIPS (Dynamic IP Service): To enable or disable the DIPS® (Dynamic IP Service) function.
4. Monitor the Image Section 47 AirLive WN-200HD User’s Manual To use this service, just follow four steps below: (1) Enable DIPS function of the device (2) Check your Device ID from this page. This is a unique number for each device. (3) If your device is behind a NAT router , please configure your device properly.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 48 Log: User can check the system log informa tion of the device, including the Main Info , Appended Info , Operator IP , and so on … Reload: Click this button; user can refresh the log information of the device.
4. Monitor the Image Section 49 AirLive WN-200HD User’s Manual Daylight Saving: Disable or enable the dayli ght saving adjustment. 4.4.3 Maintenance Hard Factory Default (Include the network setting): Recall the device hard factory default settings.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 50 Restore Setting: Click the “ Brow se” button to locate the saved backup file and then click the “ Restore Setting” button. The settings will be restored to the previous configuration.
4. Monitor the Image Section 51 AirLive WN-200HD User’s Manual 5. Once the firmware file was selected, click “ Firmware Upgrade ” button. 6. The upgrade progress information will be disp layed. Once the uploading process completed, the device will reboot the system automatically.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 52 4.5.1 Common Text Overlay Setting: There are some important informati on can be embedded into image, including date, time, and/or text. Video Profile: User can only choose either 720P or 2 Mega modes.
4. Monitor the Image Section 53 AirLive WN-200HD User’s Manual 4.5.2 Video Profile Name: Assign a name to the selected profile. Video Type: Video codec of the se lected video profile. Resolution: Resolution of the selected video profile. ROI: Assign the selected profile as a ROI stream or not.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 54 For VBR, user should choose the quality level to set the video quality rather than bit rate. The quality level is bet ween 1 and 100. The higher value can reach the better quality but of course will consume higher bandwidth.
4. Monitor the Image Section 55 AirLive WN-200HD User’s Manual 4.6 Audio – Audio Parameters 4.6.1 Setting Audio: To enable or disable audio function.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 56 Mute While PT: Mute the audio while pan and/or tilt motion Audio Mode: To select Simplex or Fu ll duplex (2-way audio) mode Input Gain: To adjust gain of input audio Output Gain: To adjust gain of output audio 4.
4. Monitor the Image Section 57 AirLive WN-200HD User’s Manual PTZ Control: Authorize this user to control PTZ function or not. Add, update, and remove of Users account: Manage the user’s account of viewer user. 4.6.3 E-Mail You may setup SMTP mail parameters for further operation of Event Schedule.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 58 SMTP Server: Type the SMTP server name or the IP address of the SMTP server. Test: Send a test mail to mail server to che ck this account is available or not. SMTP Port: Set port number of SMTP service.
4. Monitor the Image Section 59 AirLive WN-200HD User’s Manual Add and Del: To add or delete the moti on windows. User can specify up to 10 Included and/or Excluded windows to monitor the video captured by this device. By dragging mouse on the image, you can change the position and size of the selected motion window accordingly.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 60 Sensitivity Defines the sensitivity value of motion detection. The higher value will be more sensitivity. 4.6.5 Storage – Status and Configuration of SD card This page shows the status of atta ched SD card.
4. Monitor the Image Section 61 AirLive WN-200HD User’s Manual 4.6.6 Recording List- Files List inside SD Card This page shows the files list information. User may play or delete the selected file. 4.6.7 Event Sever z FTP Server You may setup FTP parameters for further operation of Event Schedule.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 62 Name: User can specify multiple FTP paths as wish. Therefore, user needs to specify a name for each FTP setting. FTP Server: Type the server name or the IP address of the FTP server.
4. Monitor the Image Section 63 AirLive WN-200HD User’s Manual FTP Path: Set working directory path of FTP server. FTP Passive Mode: Select passive or active mode connecting to FTP server. z TCP Server In addition to send video file to FTP se rver, the device also can send event message to specified TCP server.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 64 z HTTP Server The device also can send event message to specified HTTP server. Name: User can specify multiple HTTP server s as wish. Therefor e, user needs to specify a name for each HTTP server setting.
4. Monitor the Image Section 65 AirLive WN-200HD User’s Manual Proxy Login name: Type the user name for the HTTP Proxy. Proxy Login Password: Type the password for the HTTP Proxy. Proxy Port: Set port number of Proxy. z SAMBA Server The device also can send video str eam to specified SAMBA server.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 66 SAMBA Login name: Type the user name for the SAMBA server. SAMBA Login Password: Type the password for the SAMBA server. SAMBA Path: Set working directory path of SAMBA server. 4.
4. Monitor the Image Section 67 AirLive WN-200HD User’s Manual Type: Event trigger or Schedule trigger. Enable Time: Define the feasible time slot. Trigger by: Select the triggered sources. Action: Define the actions once event triggered. Example 1: Send file to FTP server by motion triggered always: 1.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 68 Example 2: Send file to E-Mail server by motion tr iggered from Friday 18:00 to Saturday 06:00 1. Select event trigger. 2. Enable time: start from Friday 18: 00 and keep work in 12 hous, so it will stop on Saturday 06:00.
4. Monitor the Image Section 69 AirLive WN-200HD User’s Manual Example 3: Enable Voice Alert every 10-minute during 18:00 to 24:00 from Monday to Friday. 1. Type: Select schedule trigger and interval is 10-minute. 2. Enable time: Select Monday to Fr iday, and set start time from 18:00 and keep work in 6 hours.
4. Monitor the Image Section AirLive WN-200HD User’s Manual 70 z Record User can choose the type of record f ile for event or schedule application. Record File Type: Choose JPEG, AVI-JPEG, or AVI-H.264 file format. Record File Prefix: Define the prefix of recorded filename.
4. Monitor the Image Section 71 AirLive WN-200HD User’s Manual Post-Trigger Duration: Define the maximum duration of post-alarm. Max File Size: Define the maximum buffer size of record file.
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 72 5 5. Troubleshooting & FAQ 5.1 Monitor the Image Section Question Answer or Resolution Features The video and audio codec is adopted in the device. The device utilizes H.264, MPEG4 and JPEG triple compression to providing high quality images.
5. Troubleshooting & FAQ 73 AirLive WN-200HD User’s Manual installed and work if a firewall exists on the network. ordinary data communication. The HTTP port and RTSP port need to be opened on the fi rewall or NAT router. The username and password for the first time or after fac tory default reset Username = admin and password = airlive .
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 74 to the IP camera. Please contact your dealer to get the approval routers list. Some IP cameras are working but others are failed • Maybe too many IP cameras have been installed on the LAN, and then NAT router is out of resource to support more cameras.
5. Troubleshooting & FAQ 75 AirLive WN-200HD User’s Manual an external network. Refer to your router's manual for details. • Access the Network Camera from the Internet with the global IP address of the r outer and port number of Network Camera.
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 76 downloading ActiveX controls”. The device work locally but not externally. • Might be caused from the fi rewall protection. Check the Internet firewall with your system or network administrator.
5. Troubleshooting & FAQ 77 AirLive WN-200HD User’s Manual (including Click to Center and Preset Positioning) communication stops with t he device. The image will refresh. • Other clients may be operating Pan/Tilt. • Pan/Tilt operation has r eached the end of corner.
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 78 5.2 PING The PING (stands for Packet Internet Gr oper) command is used to detect whether a specific IP address is accessible by sendi ng a packet to the specific address and waiting for a reply.
5. Troubleshooting & FAQ 79 AirLive WN-200HD User’s Manual 5.3 Bandwidth Estimation The frame rate of video transmitted from the device depends on connection bandwidth between client and server, video reso lution, codec type, and quality setting of server.
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 80 5.4 Specification Table Camera WN-200HD Image Device 2 Mega-pixel image sensor Effective Pixels 1600 x 1200 pixels Sensitivity 1.0V/lux-sec Signal to Noise 42.3dB Lens 4.3mm IP Module Video Video Encoder H.
5. Troubleshooting & FAQ 81 AirLive WN-200HD User’s Manual RTP, RTCP, IGMP, PPPoE, 3GPP, Samba, ICMP Security Password protection, IP address filtering, HTTPS encrypted data transmission , u.
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 82 Browser IE 6.0 or later, Firefox 2.0 or later, Safari Cell Phone With 3GPP player Video Player VLC, Quick Time, Real Player, Core Player Software Search & Installation IPWizard II Bundled NVR Program SecuGuard 64CH 5.
5. Troubleshooting & FAQ 83 AirLive WN-200HD User’s Manual If you have cable or DSL service, you will most likely have a dynamically assigned WAN IP Address. ‘Dynamic’ me ans that your router’s WAN IP address can change from time to time depending on your ISP.
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 84 (3) Open/set Virtual Server Ports to enable remote image viewing The firewall security features built into t he router and most router s prevent users from accessing the video from the device over t he Internet.
5. Troubleshooting & FAQ 85 AirLive WN-200HD User’s Manual Enter valid ports in the Virtual Server section of your router. Please make sure to check the box on this line to enable setti ngs. Then the device can be access from WAN by the router’s WAN IP Address.
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 86 Host your own Networked Device and much more no matter what your computer's IP address may be and even if you have dialup,.
5. Troubleshooting & FAQ 87 AirLive WN-200HD User’s Manual (3). After the columns show up at the left side, click “ Create Account”..
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 88 (4). Fill the application agreem ent and necessary information. a. Username b.
5. Troubleshooting & FAQ 89 AirLive WN-200HD User’s Manual (5). Check your e-mail mailbox. There will be an e-mail with a title “Your DynDNS Account Information“. Click the hyperlink addr ess to confirm the DDNS service that you just applied.
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 90 (6). Enter the web page http://www.dyndns.org/ again. Input your username and password that you just applied to login adm inistration interface of DDNS server. Input your account (7).
5. Troubleshooting & FAQ 91 AirLive WN-200HD User’s Manual (9). Click the “ Dynamic DNS ”. (10). Click the “ Get Started ”. (11). We could create a domai n name without any c harge at this step. First, we input the host name. (Pink No.
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 92 4. Setup the DDNS and PPPoE of Netw orked Device At last, users have to enter the web page of Networked Device and setup the necessary information of DDNS and PPPoE a fter the application of DDNS service.
5. Troubleshooting & FAQ 93 AirLive WN-200HD User’s Manual 230V, 240V is within tolerances and commonly found. Austria 230V 50 Hz Brazil 110/220V* 60 Hz *127V f ound in states of Bahia, Paran?(including Curitiba), Rio de Janeiro, S 緌 Paulo and Minas Gerais (though 220V may be found in some hotels).
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 94 controlled by adjacent switch. Though nominal voltage has been officially changed to 230V, 240V is within tolerances and commonly found.
5. Troubleshooting & FAQ 95 AirLive WN-200HD User’s Manual 5.9 UPnP Use the following steps to enabl e UPnP settings only if your operating system of PC is running Windows XP.
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 96 Click Add/Remove Windows Components The following screen will appear: Select Networking Services.
5. Troubleshooting & FAQ 97 AirLive WN-200HD User’s Manual Select Universal Plug and Play Click Details Click Next.
5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 98 Please wait while Setup configures the components. Click Finish.
デバイスAirLive WN-200HDの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
AirLive WN-200HDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAirLive WN-200HDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。AirLive WN-200HDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。AirLive WN-200HDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
AirLive WN-200HDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAirLive WN-200HDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、AirLive WN-200HDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAirLive WN-200HDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。