Directed Electronicsメーカー8004の使用説明書/サービス説明書
ページ先へ移動 of 18
.
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 What’ s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION Thank you for your purchase of Orion's 8004 amplifier . Each Orion amplifier is designed to be the leader in its class offering the most power , advanced features, and ease of use. Orion amplifiers are designed as the best affordable high end car audio amplifier money can buy .
WARRANTY Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years .
SPECIFICA TIONS 1. All channels driven, continuous 4 W load 20Hz to 20kHz, < 0.05% THD, with input voltage at 13.8VDC. 2. All channels driven, continuous 2 W load 20Hz to 20kHz, < 0.
END P ANEL LA YOUT 1. Power LED - when lit indicates that the amplifier is on. 2. Front Low-Pass Cr ossover Switch - activates 2nd order low-pass crossover . 3. Front Low-Pass Fr equency Control - adjusts the frequency of the low-pass crossover . 4. Front Gain Contr ol - continuously adjusts from 200mV to 5V for full power output.
AMPLIFIER SETTINGS Signal Input and Output Configurations The input section of the amplifier consists of a phase switch that sets the output configura- tion, gain controls, and RCA inputs. The input section makes it easy to adapt this amplifier to most system configurations.
Fine T uning the Crossover Fr equency The crossover section is marked at four frequency points for ease of system adjustment. These points are 20Hz, 250Hz, 1kHz, and 3kHz. Specific crossover points can be chosen based on the recommended operational bandwidth of your speakers.
Speaker Connections Four Channel Stereo Configuration ● Front and rear channel lowest recommended impedance is 2 W stereo ● Crossover mode, output, and gain configurations are independently adjustable between the front and rear channels. ● T wo-channel or four-channel input can be used for this configuration.
Three Channel Stereo/Bridged Configuration ● Front channels are configured for two-channel stereo operation. ● Front channel lowest recommended impedance is 2 W stereo. ● Rear channels are configured for a single channel bridged output. ● Rear channel lowest recommended impedance is 4 W.
AMPLIFIER INST ALLA TION Choosing Mounting Locations The location of your amplifier will depend on several important issues. Due to the low pro- file size of the Orion amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance.
Power for systems with a single amplifier can be supplied by most automotive electrical sys- tems. Systems with multiple amplifiers may require a higher capacity battery , alternator or the use of a storage capacitor . We strongly recommend the use of a Directed Audio Essentials power capacitor with an extra battery in larger stereo systems.
amplifier is twisted or bent. Step 6 T urn the vehicle's key switch to the off position. Step 7 Disconnect the vehicle's battery ground terminal. Step 8 Connect power wires to the amplifier (ground first, then 12 V(+) and RGC). Step 9 Connect the RCA and speaker wires to the amplifier .
Adjusting the Sound of the System Once you have checked the system's operation, adjust the sound of the system. Adjusting the sound of the system is accomplished by setting the level controls and adjusting the internal crossovers. Step 1 T urn the signal source volume control all the way down.
T roubleshooting Tips Symptom Probable Cause Action T o T ake No output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed. Fuse blown Check power wire's integrity and check for speaker shorts. Fix as needed and replace fuse.
Symptom Probable Cause Action T o T ake Distorted output Internal crossover not set Readjust crossovers. Refer to the properly for speakers Internal Crossover Configuration section of this guide for detailed instructions. Speakers are blown Check system with known work ing speakers and fix or replace as needed.
NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ___________________________________.
W arranty LIMITED TWO YEAR CONSUMER WARRANTY : Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under .
デバイスDirected Electronics 8004の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Directed Electronics 8004をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDirected Electronics 8004の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Directed Electronics 8004の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Directed Electronics 8004で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Directed Electronics 8004を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDirected Electronics 8004の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Directed Electronics 8004に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDirected Electronics 8004デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。