Directed Electronicsメーカーs680の使用説明書/サービス説明書
ページ先へ移動 of 12
model s680.
2 © 2003 Directed Electronics, Inc T ABLE OF CONTENTS CONGRA TULA TIONS Congratulations for choosing a Directed Studio neodymium component speaker system from Directed Electronics.
3 © 2003 Directed Electronics, Inc LIMITED TWO-YEAR CONSUMER W ARRANTY Directed Electronics, Inc. (DEI) promises to the original purchaser , to replace this product should it prove to be defective in.
4 © 2003 Directed Electronics, Inc Obtaining the highest quality sound reproduction in the mobile environment requires installation techniques and knowledge of vehicle interiors that go far beyond simple replacement of stock speakers.
5 © 2003 Directed Electronics, Inc INST ALLA TION PRECAUTIONS The Directed s680 neodymium separates are designed for installation into factory speaker locations, custom mounting enclosures or any flat mounting surface inside the vehicle with sufficient rear clearance.
6 © 2003 Directed Electronics, Inc FIGURE 1—WOOFER INST ALLA TION OPTIONAL 6x9 DRW-397 cut it to the proper size. If the hole is oversize, it is recommended that a spacer be built to compensate. 4. Pre-drill the holes for the mounting screws using a 1/8" drill bit.
7 © 2003 Directed Electronics, Inc TWEETER INST ALLA TION Review the Installation Precautions section of this guide before proceeding. Flush Mounting into Removed Panels 1. Disassemble the underside of the woofer mounting flange by removing the four screws from the bottom side of the tweeter bridge.
8 © 2003 Directed Electronics, Inc against the panel and mark the two holes at the rear of the housing. 3. Drill the smaller center hole using a 1/8" drill bit. This is the mounting screw hole. 4. Drill the larger off-center hole using a 3/8" drill bit, insert a grommet and route the speaker wire from the crossover through the grommet.
9 © 2003 Directed Electronics, Inc DRW-68 WIRING HARNESS FLUSH MOUNT TRIM RING TWEETER HEX HEAD BOL T FLUSH MOUNT HOUSING PANEL X-BRACKET TWEETER WIRE FIGURE 3—FLUSH MOUNTING MOUNTED P ANELS TWEETE.
10 © 2003 Directed Electronics, Inc FIGURE 6—CONNECTION/ADJUSTMENT SINGLE AMPLIFIER.
11 © 2003 Directed Electronics, Inc SPECIFICA TIONS Directed model 680 Frequency response 40 Hz - 21 kHz Power handling RMS 60 watts Power handling peak 120 watts Impedance 4 ohms Magnet weight 52.
12 © 2003 Directed Electronics, Inc The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide customers with the finest vehicle security , car stereo products, rear seat entertainment, and accessories available.
デバイスDirected Electronics s680の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Directed Electronics s680をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDirected Electronics s680の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Directed Electronics s680の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Directed Electronics s680で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Directed Electronics s680を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDirected Electronics s680の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Directed Electronics s680に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDirected Electronics s680デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。