Dixonメーカー5421の使用説明書/サービス説明書
ページ先へ移動 of 43
.
IMPORTANT - READ CAREFULLY The Dixon ZTR Mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is not a toy or a recreational vehicle. Before you start to use the mower, read the operator's manual carefully, and become completely familiar with the controls.
INDEX 1. SAFETY ............................................................... Pages 1 - 3 2. WARRANTY POLICY ........................................... Page 4 3. SPECIFICATIONS ............................................... Page 5 4. SET UP AND SERVICE .
SAFETY RIDING LAWNMOWERS, IF IMPROPERLY O PERATED, CAN CAUSE SERIOUS INJURY The following examples are the most common causes of injury to the operator or bystander... 1. BLADE CONTACT: The operator or bystander inserts a hand or foot into the discharge chute or under the mower deck and into the path of the cutting blade.
SAFETY SAFETY REMINDERS: READ CAREFULLY BEFORE OPERATION 1. Wear appropriate, safe clothing when mowing - close fitting jeans or slacks and heavy leather or safety shoes with rough soles. Never operate this mower with bare feet or open sandals. 2. Do not operate on wet or slippery grass.
SAFETY REMINDERS: (Continued) 14. Never lift lawnmower by the body, lift only by the frame. 15. Never carry passengers. 16. Use care when pulling loads or using heavy equipment. A. Use ONLY approved dra wbar hitch points. B. Limit loads to those you can safely control.
DIXON LIMITED WARRANTY POLICY -- HYDRO - GEAR MODELS This warranty policy applies to all Hydro - Gear mowers or any 50" model, purchased on or after March 1,1990. WARRANTY: Dixon Warranty term is for a period of one (1) year from date of p urchase or 400 hours of use, whichever occurs first.
SPECIFICATIONS CHASSIS: 11 GA - rectangular tube. B ODY: Two piece - made of rotational molded polyethylene. Front body contains access panels for battery service and engine to mower deck belt removal. Rear body tilts up to allow service on the entire drive system.
SET UP AND SERVICE 1. Seat Assembly Instructions 2. Upper Control Lever Installation 3. Mower Deck Installation 4. Deck Leveling 5. Final Preparation Page 6.
SEAT ASSEMBLY INSTRUCTIONS 1 . Assemble one arm rest bracket to arm rest cushion using (2) 5/1 6 standard flat washers (3020) and (2) 5/16 - 18 x 1 hex head nylok bolts (3224).
UPPER CONTROL LEVER INSTALLATION 1 Raise rear body cover to fully open position. 2. Install flat washer on right hand swive l plate weldment. Next install right hand control lever, then second flat washer. 3. Push control lever into the neutral slot and install (2) cup washers, (1) flat washer and jam nut.
MOWER DECK INST AL LATION NOTE: Brake link (P/N 5283) normally used for installation of engine to mower deck drive belt, has been placed in position during assembly of the lift frame at the factory. For shipment purposes, the brake link has been secured with a cotter pin and washer.
MOWER DECK LEVELING PROCEDURE LEVELING PRINCIPALS: A. There are a total of (4) threaded adjusters which will control the attitude or pitch of the mower deck. The adjusters have lock nuts on the bottom which can be turned up or down to raise or lower the front and rear of the mower deck.
MO WER DECK DEFLECTOR: Remove hair pin cotter (P/N 3072) from deflector pin (P/N 6297), remove pin. Position deflector (P/N 8799) on mower deck. Reinstall deflector pin and hair pin cotter. BATTERY: 1 . Remove battery from chassi s. 2. Fill each cell with electrolyte (acid) to ring at bottom of fill cap.
OPERATION INSTRUCTIONS The safe and successful operation of the Model 5421 will depend upon the operator having the correct knowledge of all controls used on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone to operate the mower without complete knowledge of all controls and their functions.
OPERATION INSTRUCTIONS: (Continued) BRAKING: To brake mower, move both levers in direction opposite of travel, release levers to neutral, set parking brake. Park only on level surfaces. GROUND SPEED: Ground speed (controlled by moveme nt of hand levers) must be carefully controlled for safety and best mowing results.
CARE AND MAINTENANCE - MODEL 5421 This portion of the Model 5421 owners manual deals with normal service items which can be performed by the owner. Please remember that if you are in doubt as to the c.
PROCEDURE FOR ELECTRIC CLUTCH ADJUSTMENT Dixon has used two types of electric clutches. One type is the Borg Warner and the second one is the Ogura. Even though these clutches come from different manufacturers, the test procedures are the same for both.
CARE AND MAINTENANCE - MODEL 5421 MOWER DECK SERVICE CUTTER BLADE REMOVAL - BELT TENSION: "CAUTION" The removal of the cutter blades for either sharpening or replacement is best accomplished by removing the deck assembly from the mower.
CARE AND MAINTENANCE - MODEL 5421 DRIVE SYSTEM ADJUSTMENTS: Adjustment of the drive system is limited to the actual function of the hydrostatic transmissions as outlined below . 1 . The idler pulley travel required to engage the belt drive should be held to approximately 1 3/4".
Page 18.
FORWARD LEVER STOP ADJUSTMENT Page 19.
CARE AND MAINTENANCE - MODEL 5421 LUBRICATION CHASSIS AND MOWER DECK: Number of grease zerks used: (7) LOCATIONS: (1) each front wheel caster, front wheel, and deck hub for front wheels SERVICE INTERV.
CARE AND MAINTENANCE - MODEL 5421 CLEANING THE MOWER: A clean machine is a source of pride to the owner. However, cleaning by use of high pressure commercial washes is not recommended.
TROUBLESHOOTING MOW ER CUT QUALITY: There are many variables that can effect the cut quality of any multi - blade mower. Type and conditions of grass, cut height setting, engine RPM and ground speed are some of the variables that interact creating differences in cut quality.
DRIVE SYSTEM: TROUBLESHOOTING Page 23 SITUATION CAUSES REMEDY Mower pulls to one side or the other Drive adjustment Adjust per operators manual Consult your dealer for repai r Loss of drive power on o.
TROUBLE SHOOTING ELECTRICAL SYSTEM: SITUATION CAUSES REMEDY Starter will not turn engine over Circuit breaker engaged Push button to reset Consult your dealer for repair Starter will not turn engine o.
Page 25.
Page 26.
Page 25.
Page 26.
Page 27.
Page 28.
Page 29.
Page 30.
Page 31.
ZTR 5421 PARTS LIST 1108 Front Tire 3093 5/1 6" - 1 8 UNC X 1 " HH Bolt GR5 1109 Inner Tube - Front Wheel 3100 7/1 6" HD Flat Washer 1384 Tank Mount Bracket (Short) 3106 1/4"X1&quo.
ZTR 5421 PARTS LIST 4584 Start Cable 5643 Input Gear - GB 4585 Battery Ground Cable 5644 Bearing - Gearbox 4587 W ire Cover 61 " 5645 Bearing Spacer - GB 4589 Covered Key 5648 CW Fan - Machined 4.
ZTR 5421 PARTS LIST 8576 Rear Rim 9624 Lift Cam Drilled RH 8688 Mower Blade Hi - Lift 9634 Lift Frame Weldment 8772 Belt Set (1859) 9646 Lift Plate 8852 Fuel Line 26.
Page 36 NOTES.
NOTES Page 37.
Page 38 NOTES.
DIXON INDUSTRIES, INC A BLOUNT COMPANY AIRPORT INDUSTRIAL PARK PO BOX 1569 COFFEYVILLE KS 67337 O945 316 251 2OOO FAX 316 251 4117.
デバイスDixon 5421の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Dixon 5421をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDixon 5421の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dixon 5421の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dixon 5421で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dixon 5421を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDixon 5421の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dixon 5421に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDixon 5421デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。