DixonメーカーZTR 2300の使用説明書/サービス説明書
ページ先へ移動 of 52
Model Y Model Y Model Y Model Y Model Y ear 200 ear 200 ear 200 ear 200 ear 200 4 4 4 4 4 ZTR® 1950-2300 Series.
IMPORTANT - READ CAREFULLY The Dixon ® ZTR ® Mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is not a toy or a recreational vehicle. Before you start to use the mower, read the operator’s manual carefully and become completely familiar with the controls.
3 INDEX Page Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Warranty Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 RIDING LAWN MOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY OR DEATH. The most common causes of injury to the operator or bystander... ...read and understand this manual to prevent injuries.
5 Safety Alert Symbol When you see this symbol, BE ALERT to the potential for injury. DANGER (highlighted in red) indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
6 Failure to observe the following safety instructions could result in serious injury or death. GENERAL OPERATION: •Read, understand, and follow all instructions in the manual and on the mower before starting. •Only allow responsible adults, who are familiar with the instructions, to operate the mower.
7 GENERAL OPERATION (continued) : •Turn off blades when not mowing. •Stop engine before removing grass catcher or unclogging chute. •Mow only in daylight or good artificial light. •Do not operate the mower while under the influence of alcohol or drugs.
8 SAFETY SLOPE OPERATION: Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it! DO Mow across the slope with your Dixon ZTR - never up or down.
9 SAFETY SLOPE OPERATION (continued): DO (continued): Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly down the slope. If front wheels lift off the ground, pull the levers back to stabilize the mower.
10 SERVICE: •Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. Use only an approved container. Never remove fuel cap or add fuel with engine running. Allow engine to cool before refueling. Do not smoke while refueling.
11 SERVICE (continued): •Never run a mower inside a closed area. The exhaust fumes are toxic. •Keep nuts and bolts tight, especially blade attachment bolts, and keep equipment in good condition. •Never tamper with safety devices. Check their proper operation regularly.
12 SAFETY CHILDREN: Tragic accidents can occur if the operator is not alert to the presence of children. Children are attracted to lawn mowers and the mowing activity. NEVER assume children will stay where they were last seen. Be alert to avoid accidents.
13 DIXON LIMITED W ARRANTY POLICY Pro Models 1950 ~ 2300 ~ 2560 DIXON ZTR MOWERS ARE W ARRANTED AGAINST DEFECTS IN MA TERIALS AND WORKMANSHIP AND PROVIDES FOR REPLACEMENT OR REP AIR OF P ARTS INCLUDING LABOR COSTS. THIS WARRANTY IS SUBJECT TO THE FOLLOWING CONDITIONS AND LIMIT A TIONS.
14 SPECIFICATIONS Model ZTR 1950 and 2300 CHASSIS: 11 GA - rectangular tube SEAT: Designed for operator comfort by use of high-density closed cell foam padded back and arm rests, upholstered with Cordura TM water- repellent fabric. Seat is adjustable fore and aft.
15 SEAT ADJUSTMENT INSTRUCTIONS Models 1950 & 2300 1 . Grasp seat slide adjuster and move it into adjustment position. 2 . Slide seat forward or backward.
16 CONTROLS CONTROL LEVERS Note: For access to the seat, move control levers to neutral position and swing them outward. TO GO FORWARD: • From neutral position, gently push both control levers forward. • To increase speed, move levers further forward.
17 CONTROLS CHOKE CONTROL LEVER: • Located on control panel to operator’s right. • Used to start a cold engine. THROTTLE CONTROL LEVER: • Located on control panel to operator’s right.
18 CONTROLS PARKING BRAKE: The parking brake is designed to hold the mower from moving and is not intended for use in stopping the mower while it is in motion. CAUTION Engage parking brake before starting engine. TO SET PARKING BRAKE: The hand operated brake is located at the left hand side of the mower.
19 CONTROLS MOWER DECK CUT HEIGHT LIFT LEVER: •Located to the right and front of operator. •Controls the cutting height. •Eight positions of adjustment. •Depress trigger and move lever forward to lower deck. •Depress trigger and pull lever back to raise deck.
20 OPERATION INSTRUCTIONS The safe and successful operation of the 1950 or 2300 Series will depend upon the operator having the correct knowledge of all controls used on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone to operate the mower without complete knowledge of all the controls and their functions.
21 BEFORE OPERATING MOWER: 1. Read and observe all safety instructions on your mower and in the manual. 2. Read engine manufacturer’s operating and maintenance instructions. 3. Discuss proper maintenance with your dealer. 4. Check engine oil. 5. Check fuel cap to be sure it is in place.
22 OPERATION INSTRUCTIONS TO FREE WHEEL MACHINE (UNLOCK TRANSMISSION): Always turn off engine before engaging or disengaging the hydro release (free wheel) valves. Never attempt to move the valves with the engine running. The hydro release valves are located beneath the seat, on the front side of the hydro pumps.
23 OPERATION INSTRUCTIONS TESTING OF SAFETY INTERLOCK SYSTEMS: Do not operate mower if safety switches are not operating properly. PARKING BRAKE SWITCH TEST: a) Place parking brake in OFF position. b) Turn ignition switch to START. ENGINE SHOULD NOT TURN OVER OR ATTEMPT TO START! BLADE DRIVE SWITCH TEST: a) Place parking brake in ON position.
24 OPERATION INSTRUCTIONS SIDE DISCHARGE OF THE CLIPPINGS: In order to achieve optimum performance when side discharging the grass clippings, please read and follow the tips listed below. Additional information can be found in the troubleshooting guide.
25 OPERATION INSTRUCTIONS GRASS HEIGHT AND CUTTING SUGGESTIONS: Do not attempt to cut grass when it is wet. If the grass is tall, place the mower deck cut height lever in the top or second notch. “Initially” overlap cutting swaths instead of a full swath with each pass.
26 OPERATION INSTRUCTIONS CAUTION Do not operate the engine in an enclosed area due to the harmful exhaust gas produced. STARTING INSTRUCTIONS (cold engine): 1. Position choke control in “on” position. 2. Position throttle control at 1/2 speed setting.
27 STARTING INSTRUCTIONS (engine has been operated): 1. Move throttle control to 1/4 to 1/2 setting. 2. Insert ignition key and turn to “start” position. When engine starts, release ignition key. Key will return to “run” position. 3. Move throttle control to “fast” position.
28 OPERATION INSTRUCTIONS MOWING WITH A MULCHING ATTACHMENT: Mulching or recycling the grass clippings requires a totally different mowing approach than would be normal when side discharging or bagging the grass. There may be instances or conditions where it is not possible to hide all of the recycled or mulched clippings.
29 OPERATION INSTRUCTIONS MOWING WITH A MULCHING ATTACHMENT (continued): 6. Keep the Underside Of The Mower Deck Clean. Remove all grass and dirt build-up from the underside of the pan, the baffles and deflectors after each use. 7. Alternate mower direction.
30 OPERATION INSTRUCTIONS MOWING WITH A GRASS CATCHER ATTACHMENT: In order to achieve optimum performance when mowing with a grass catching attachment, please read and follow the tips listed below. 1. Set engine speed control to the wide open or full setting.
31 OPERATION INSTRUCTIONS MOWING WITH A GRASS CATCHER ATTACHMENT (continued): 7. Operate the mower at a slower ground speed than when mowing without a grass catching attachment. 8. Some mowing applications/use of grass catchers may require that an optional weight box be fitted to the mower to counter the weight of grass in the bags.
32 OPERATION INSTRUCTIONS DECK ROLLERS (60” deck): Purpose: The spring loaded deck rollers located at the front corners of the 60” mower deck are designed as an aid to limit turf scalping when mowing on uneven ground. Height: Normal height settings as installed at the factory allows each roller to ride slightly above the turf.
33 CARE AND MAINTENANCE CAUTION Before performing any maintenance, turn off engine, allow to cool & remove key. Use extreme care when working on machinery. Do not wear watch or jewelry. Do not wear loose fitting clothes, and observe all common safety practices with tools.
34 CARE AND MAINTENANCE ENGINE: For complete maintenance and operating information of the engine, please refer to the maintenance instructions furnished by the engine manufacturer and included in your Zero Turn Radius mower information packet. BATTERY: • This is a maintenance-free battery and the fluid level cannot be checked.
35 CARE AND MAINTENANCE CUTTER BLADE MAINTENANCE: CAUTION Stop engine and remove ignition key for safety. Wear heavy, thick gloves when holding onto cutter blade, avoid the sharp edge of the blade. Check sharpness of mower blades after every 10 hours of operation.
36 CARE AND MAINTENANCE BELTS: Check belts every 50 hours. Replace any belts found to be in poor condition. BELT TENSION: Engine to Mower Deck Belt: P/N 6111 (50”) P/N 6938 (60”) The engine to mow.
37 LUBRICATION: CHASSIS: (7) grease zerks used LOCATIONS: (1) each brake band shaft (1) each front wheel caster tube (1) each mower deck hub SERVICE INTERVALS: Every 50 hours of operation RECOMMENDED GREASE: Name brand wheel bearing or multi-purpose grease.
38 Hex Head Valve Stem Hot oil may cause burns. Allow engine to cool before draining oil. CAUTION CARE AND MAINTENANCE CHANGING THE ENGINE OIL: 1. The “Dapco” oil drain valve is located on the right side of the engine crankcase on the 1950 and on the left side of the engine crankcase on the 2300.
39 CARE AND MAINTENANCE OIL FILL: 1. Drain oil. 2. Clean any spilled oil from engine and chassis. 3. Refill engine with type, and quantity of oil recommended by the engine manufacturer in engine literature. OIL FILTERS: 1. Replace filter each time the oil is changed.
40 CARE AND MAINTENANCE HYDROSTATIC TRANSMISSION OIL & FILTER SERVICE: Dirt or water in oil can ruin the hydrostatic transmissions. SERVICE INTERVALS: 1. Initial filter service - 50 hours 2. Every 250 hours or once a year thereafter. OIL REQUIREMENTS: Any high quality engine oil with an API classification of SG/CD is recommended.
41 CARE AND MAINTENANCE HYDROSTAT OIL MAINTENANCE PROCEDURE: Check the oil level in hydrostatic transmisison oil reservoir after every 25 hours of usage. Clean the oil reservoir cap and the area around it prior to removal. Check the oil level. Oil should be approximately 1-3/8” below top of oil tank.
42 CARE AND MAINTENANCE ELECTRICAL SYSTEMS: Keep all connections clean and tight. CLEANING THE MOWER: Wash mower periodically. Clean above and below deck. High pressure washing and alkaline based soaps can cause damage to bearings and other parts of the mower.
43 CARE AND MAINTENANCE 5283 Link Front of lift frame Insert end of link here MOWER DECK REMOVAL: 1. Remove mower deck drive belt. To relieve belt tension, insert 5283 link (at front of lift frame) into tab illustrated below. Move lift handle into the lowest cut position.
44 CARE AND MAINTENANCE MOWER DECK LEVELING PROCEDURE: There are a total of (4) threaded adjusters which will control the attitude or pitch of the mower deck. The adjusters have locknuts on the bottom which can be turned up or down to raise or lower the front and rear of the mower deck.
45 Left Rear Adjuster Front Adjusters CARE AND MAINTENANCE MOWER DECK LEVELING PROCEDURE (continued): D . Turn both outer blades to align with the deck in front- to-rear manner. Turn left rear adjuster nut up or down until rear of mower deck is positioned level to 1/8” higher in the rear than the side-to-side measurement.
46 CARE AND MAINTENANCE STEERING CONTROL ADJUSTMENTS: To adjust neutral: 1. Lift seat. 2. Block up the unit so that the drive wheels are off the ground. 3. Loosen ball joint jam nuts on control rod. Note: The front jam nuts are left hand threads. 4. With steering control arms in the “out” neutral position, start the engine and run at fast idle.
47 CARE AND MAINTENANCE STEERING CONTROL ADJUSTMENTS (continued): To adjust neutral springs: 1. Loosen set screws on center spring stop collar located on the control rods. (Requires a 1/8” Allen wrench). 2. Swing control lever out. Tighten set screw on lock collar.
48 1. ENGINE WON’T TURN OVER Mower blades engaged- - - - - - - - - - - - - - - - - -disengage blades Drive not in neutral - - - - - - move control levers to neutral “OUT” Circuit breaker trips- .
49 TROUBLESHOOTING 6. ENGINE RUNS BUT MOWER WON’T MOVE FORWARD Drive belt broken or slipping- - - - - - - - - - - - - - - - - - -replace drive belt Transmission oil low- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -add oil Transmission locks in free-wheel position- - - - lock position( see pg.
50 STANDARD SERVICE PARTS LIST 50” Deck Blades Hi-Lift - P/N 9444 (Standard) Lo-Lift - P/N 9443 Belts Engine to Mower Deck - P/N 6111 Serpentine - P/N 1300 Engine to Hydros - P/N 2469 60” Deck Bla.
51 OWNER INFORMATION Date Purchased _ ______________________________ Mower Model Number__________________________ Mower Serial Number ____________________________ Purchased From ___ __________________.
ZTR®Mowers ZTR®Mowers ZTR®Mowers ZTR®Mowers ZTR®Mowers Dixon® and ZTR® are registered trademarks of Dixon Industries, Inc. DIXON INDUSTRIES, INC. a BLOUNT International Inc. Co. P.O. Box 1569 Coffeyville, Ks 67337-0945 620-251-2000 1950/2300 Part No.
デバイスDixon ZTR 2300の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Dixon ZTR 2300をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDixon ZTR 2300の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dixon ZTR 2300の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dixon ZTR 2300で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dixon ZTR 2300を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDixon ZTR 2300の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dixon ZTR 2300に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDixon ZTR 2300デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
