DMP ElectronicsメーカーLT-0229 (5 97)の使用説明書/サービス説明書
ページ先へ移動 of 18
LT-0229 (5/97) XR10/XR20 Command Processor Panels Installation Guide 10/26 Zone Burglary/Fire/Access Control Panels with Built-in Communicator 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 : http://www.
MODEL XR10/XR20 COMMAND PROCESSOR INST ALLA TION GUIDE FCC NOTICE This equipment generates and uses radio frequency energy and, if not installed and used properly in strict accordance with the manufacturer's instructions, may cause interference with radio and television reception.
TABLE OF CONTENTS Panel Specifications Power supply ........................................................................................ 1.1 Communication .................................................................................... 1.2 Panel zones .
TABLE OF CONTENTS Section Reset Jumpers J16 Description ......................................................................................... 14.1 Universal UL Burglary Specifications Introduction ..................................................
Page 1 Introduction 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide Panel Specifications 1.1 Power supply Transformer Input: 16.
Page 2 Introduction 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide 2.3 Before you begin Before installing the XR10/XR20, we recommend you read through the entire contents of this guide. Familiarize yourself with the features of the panel and the key points to remember during the installation.
Page 3 Introduction 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide System Components 3.1 Description The DMP XR10/XR20 system is made up of an alarm panel with built in communicator, an enclosure, a 16.5 VAC transformer, and a 12 VDC 6.
Page 4 Installation 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide Installation 4.1 Mounting the enclosure The metal enclosure for the XR10/XR20 must be mounted in a secure, dry place to protect the panel from damage due to tampering or the elements.
Page 5 Installation 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide 4.2 Mounting keypads Security Command keypads have removable covers that allow you to easily mount the base with keypad circuit board to a wall or other flat surface using the screw holes provided on each corner.
Page 6 Installation 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide 6.4 Discharge/recharge The XR10/XR20 battery charging circuit float charges at 13.9 VDC at a maximum current of 1.2 Amps using a 40VA transformer.
Page 7 Installation 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide Bell Output 7.1 Terminals 5 and 6 Nominal 12 VDC is supplied by terminal 5 on the panel to power alarm bells or horns. The output is rated for a maximum output of 1.
Page 8 Installation 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide 10.2 Operational parameters Each burglary protection zone detects three conditions: open, normal, and short. The parameters for each are listed below: Condition Resistance on zone Voltage on right terminal Open over 1300 ohms over 2.
Page 9 Installation 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide Annunciator Outputs 12.1 Description The four annunciator outputs can be programmed to indicate the activity of the panel's zones or conditions occurring on the system.
Page 10 Installation 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide 13.4 Ground start To configure the XR10/XR20 for ground start operation, you must install the appropriate ground start module and program one of the panel's available annunciator outputs for Ground Start operation.
Page 11 Installation 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide UNIVERSAL UL BURGLARY SPECIFICATIONS 15.1 Introduction The programming and installation specifications contained in this section must be completed when installing the XR10/XR20 panel in accordance with any of the UL burglary standards.
Page 12 Installation 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide UL 1610 and 1076 SPECIFICATIONS Central-Station and Proprietary Burglar-Alarm Units 17.1 Opening/Closing reports The Opening/Closing Reports option must be programmed as YES.
Page 13 Installation 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10/XR20 Installation Guide 19.6 Mercantile Safe and Vault When the DMP Model 349A housing is used, the XR10/XR20 provides operation as a mercantile safe and vault alarm.
Page 14 Troubleshooting 2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 XR10 Installation Guide Problem Possible Cause Solution Security Command keypads display " SERVICE REQUIRED" J16 reset jumper is installed. Open or short on the green data wire to the keypad.
デバイスDMP Electronics LT-0229 (5 97)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
DMP Electronics LT-0229 (5 97)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDMP Electronics LT-0229 (5 97)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。DMP Electronics LT-0229 (5 97)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。DMP Electronics LT-0229 (5 97)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
DMP Electronics LT-0229 (5 97)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDMP Electronics LT-0229 (5 97)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、DMP Electronics LT-0229 (5 97)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDMP Electronics LT-0229 (5 97)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
