DometicメーカーNDR1062の使用説明書/サービス説明書
ページ先へ移動 of 20
INST ALLA TION AND OPERATING INSTRUCTIONS REFRIGERA TOR FOR LP-GAS AND ELECTRIC OPERA TION NDR1062 USA Corporate Office CANADA Service Office 2320 Industrial Parkway Elkhart, IN 46515 Dometic Distribution Inc. Dometic Corporation 866 Langs Drive 2320 Industrial Pkwy .
.
3 FIG. 2 Refrigerator control p anel ON OFF AC GAS AU TO CHECK COLD 1 2 3 4 5 COLDEST B AD C 2 1 E 3 F G LEGEND 2-W A Y AMES Model 1. Main Power Button ON/OFF 2. AUTO/GAS Mode Selector Button 3. T emperature Selector Button A. AUTO Mode Indicator Lamp B.
4 INST ALLA TION GENERAL INSTRUCTION This appliance is designed for storage of foods and storage of frozen foods and making ice. This appliance is certified under the latest edition of ANSI Z21.
5 12 V olt s DC Connection This refrigerator model require a continuous 12 volt DC supply to maintain the automatic energy system. The connection is made to the positive (+) and negative (-) terminals located at the rear of the refrigerator . (See FIG .
6 2. Once the lower front strip is slipped under the hinge, the part is possible to swing into place as shown in FIG . 6. 3. Secure the refrigerator and the lower front strip with two screws: One screw through the hinge, and on the opposite side one screw through the lower front strip.
7 CERTIFIED INST ALLA TION Certified installations require one roof vent and one lower side vent. For “Certified V ent System Kit s” see p age 16 .
8 OPERA TING INSTRUCTIONS IMPORT ANCE OF LEVELING A REFRIGERATOR In an absorption refrigerator system, ammonia is lique- fied in the finned condenser coil at the top rear of the refrigerator.
9 THERMOST A T The thermostat on the refrigerator controls both the gas and electric operation, thereby eliminating the necessity of resetting each time a different energy source is em- ployed. After the initial start-up, the thermost at should be moved from “COLDEST” to the desired temperature setting, usually at mid setting.
10 DESCRIPTION OF OPERA TING MODES AUTO MODE When operating in the AUTO mode, the AUT O mode indicator lamp (A) will illuminate. The control system will automatically select between AC and GAS operation with AC having priority over GAS.
11 ! WARNING When all the frost has melted, dry the interior of the re- frigerator with a clean cloth. Replace all food and set the thermostat to the COLDEST temperature setting for a few hours. Then reset the thermostat to the desired set- ting, usually at mid setting.
12 ELECTRIC EQUIPMENT HEA TER The heat necessary for the operation of an absorption cooling unit is supplied by an electric heater mounted in a pocket of the boiler system. This model is equipped with one electric heater for 120 volt AC. To replace the heater proceed as follows: 1.
13 B . Check all connections in the LP gas system (at the back of the refrigerator) for gas leaks. The LP gas supply must be turned on. Apply a non-corrosive bubble solution to all LP gas connections.
14 TROUBLESHOOTING The Refrigerator Does Not Cool Properly A. Burner jet clogged. Clean. (See Section Maintenance & Service, item 2. Periodic maintenance, Paragraph E item 1-13. B. Check level of refrigerator. C. Venting problem. Restriction in air flow across cooling unit.
15 1 1 1 2 1 1 1 3 3 4 5 P ANEL DIMENSIONS MAX. THICKNESS 5/32" (4 mm) REFR. MODEL HEIGHT WIDTH TYPE MAX. MIN. MAX. MIN. NDR1062 upper m m 403 401 527 524 inch 15-27/32 15-25/32 20-3/4 20-5/8 low.
16 CERTIFIED VENT SYSTEM KITS REFRIGERATOR KIT MODEL NO. COMPONENTS PART NO. NDR1062 4A Roof Base 3103633.XXX* Roof Cover 3103634.XXX* Lower Side V ent 3109350.XXX* * Fill in “XXX” with color code numbers. For color codes, contact your supplier. For further information contact your dealer or distributor.
17 Put a screwdriver into the slot of the shelf lock. Turn the screwdriver counterclockwise. Remove the shelf locks from the wire shelf. Insert the ends of the wire shelf on the left-hand side at the desired position. Slide the wire shelf to the left.
18 NDR1062.
19.
20 MO-FO 0445.
デバイスDometic NDR1062の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Dometic NDR1062をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDometic NDR1062の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dometic NDR1062の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dometic NDR1062で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dometic NDR1062を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDometic NDR1062の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dometic NDR1062に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDometic NDR1062デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。