EarthStoneメーカーBV400C-2の使用説明書/サービス説明書
ページ先へ移動 of 28
PAGE 1 INSTALLATION AND OPERATION MANUAL MODEL BV400C-2 RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE EPA CERTIFIED CATALYTIC WOOD BURNING FIREPLACE INSERT THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. READ ENTIRE MANUAL THOROUGH LY BEFORE INSTALLATION.
IMPORTANT WARNINGS CAUTION: PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR NEW ROOM HEATER. FOR YOUR SAFETY, FOLLOW THE INST ALLATION, OPERATION AND MAINTENANCE INSTRUC- TIONS EXACTLY, WITHOUT DEVIATION. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH.
PAGE 3 TABLE OF CONTENTS Important Warn ings ................................................ 2 Testing/Listing, EPA, Using this Manual .................. 3 Planning Your Inst allation ..................................... 4-6 Installati on ..........
PLANNING YOUR INSTALLATION PAGE 4 QUESTIONS TO ASK LOCAL BUILDING OFFICIAL A correct installation is critical and imperative for reduc- ing fire hazards and perilous conditions that can arise when wood burning appliances are improperly installed. The installer must follow all of the manufacturers’ instruc- tions.
PLANNING YOUR INSTALLATION PAGE 5 CLEARANCES WARNING: IT IS VERY IMPORTANT THAT YOU OB- SERVE THE MINIMUM CLEARANCES. DO NOT STORE FIREWOOD WITHIN THIS CLEARANCE SPACE.
PLANNING YOUR INSTALLATION PAGE 6 FACTORY BUILT FIREPLACES This appliance is approved for installation into a listed factory built solid fuel burning fireplace.
INSTALLATION PAGE 7 FIREPLACE INSTALLATION BV400C-2 MINIMUM FIREPLACE DIMENSIONS Approximate minimum dimensions into fireplace: Height: 20” Width: (front-29 ¾”), (rear-21 ½”) Depth: 15 ¾ CATALYTIC TEMPERATURE PROBE Install temperature probe prior to installing insert .
INSTALLATION PAGE 8 INSTALLATION STEPS 1. Remove all ashes from the fireplace. 2. Remove all materials inside the insert and set them aside. 3. Remove the surround panel (face shield) and at- tach insulation material provided using a nonflam- mable adhesive (i.
INSTALLATION PAGE 9 14. Push the insert to its desired position in the fire- place. The depth may vary as long as the starter pipe or other connecting pipe system can be effec- tively installed.
INSTALLATION PAGE 10 POSITIVE FLUE CONNECTION FOR MASONRY FIRE- PLACE A Professional should inspect chimney prior to installation to determine if any repairs are nece ssary or if a chimney reline is necessary. The fireplace damper must be secured in the open position.
PROCUCT FEATURES AND CONTROLS PAGE 11 BLOWER SYSTEM The 500-CFM room air circulat ion blower system comes equipped with a variable speed control (rheostat). The blower system can be operated manually or set to oper- ate automatically (so the blowers will turn on when the insert is hot and turn off when the insert is cool).
CARE AND OPERATION PAGE 12 FUEL DOOR CAUTION: When opening the door, do not extend it beyond its normal travel. Ov erextending the door to a further open position can put excessive stress on hinge area of door and hinge pins and may result in breakage.
CARE AND OPERATION PAGE 13 BREAK-IN PERIOD Your fireplace insert finish is a high temperature paint that requires time and temperature to completely cure. We recommend that you vent ilate the house during the initial burns. The paint emits non-toxic odors during this process.
CARE AND OPERATION PAGE 14 BLOWER SYSTEM The Blower System consists of a ON/OFF rocker switch, a variable speed blower speed control switch (rheostat), a thermally activated switch (fan disc) and 4 axial blow- ers. When starting a fire, leave the blower system off until the insert is thoroughly heated (approx.
MAINTENANCE PAGE 15 BURN RECOMMENDED FUEL This appliance is approved for use with natural dry wood only. Burning materials other than natural wood will shorten the life of the catalytic com bustor. Do not burn particleboard or pressed logs using bonding agents as they can produce conditions which will deteriorate metal or damage the cata- lyst.
MAINTENANCE PAGE 16 DOOR / GLASS GASKET AND ASH DUMP GASKET A 3/4" spun fiberglass gasket provides the seal around the fuel door and a flat spun fiberglass rope gasket (1/8” x 1”) provides the seal ar ound the glass.
MAINTENANCE PAGE 17 CLEANING BLOWERS The blowers require inspection and cleaning annually to remove lint, dust, etc. If there are pets in the dwelling, the blowers should be cleaned at least twice a y.
TROUBLESHOOTING PAGE 18 * SMOKES OUT FUEL DOOR WHEN OPEN 1. The primary air control is closed. 2. The chimney is too cool. Set the primary air con- trol on "HIGH" with the bypass damper control "OPEN" for a few minutes before opening the fuel door.
TROUBLESHOOTING PAGE 19 OVERFIRING If any part of the appliance glows, it is overfiring. Other symptoms may include: Cracking, warping or burning out of components, catalytic combustor may deteriorate, gold doors may turn color, stove glass may develop a haze which will not come off with cleaning, firebox baffle plate (tunnel baffle) may warp, etc.
SPECIFICATIONS - Model BV400C-2 PAGE 20 Maximum log length 24" Flue size 8" Width w /standard surround 48" Width at fireplace opening 29 1/2" Width at rear of firebox 21 1/2" .
COMPONENT DIAGRAMS – Model BV400C-2 PAGE 21 ITEM NO DESCRIPTION Door and Glass Parts 27M67 Clip Set, Glass H0537 Door Assembly, Gold (handle included) 86-128 Gasket Kit, 3/4" Door Rope (include.
COMPONENT DIAGRAMS – Model BV400C-2 PAGE 22 Firebox Parts 11711 Cover, Ash Dump (w/ Gasket 4 1/4 x 8 3/8" x 1/2") 26M70 Damper Kit, Bypass (damper, linkage and rod) LB-102215 Damper Stop (.
COMPONENT DIAGRAMS – Model BV400C-2 PAGE 23 REPLACEMENT DAMPER KIT (Cat. No. 26M70) DOOR ASSEMBLY - Cat. No. H0537 (Gold) and Cat No. H0538 (Black) (Includes Handle Assembly, Not Shown) HANDLE ASSEMBLY (P/N LB-102214) DRAFT MODULE ASSEMBLY (Cat. No.
OPTIONAL ACCESSORIES - Model BV400C-2 PAGE 24 Accessories Part/ Cat. No. Model Description 14M69 AD-BV400C Ash Drawer – Includes taller sur- round side trim-35 ½” because ash drawer adds 3 ½” to height of insert. 14M77 OA400-8 8” to 8” Offset Adapter for flue outlet.
SAFETY / LISTING LABEL PAGE 25.
EPA LABEL PAGE 26.
OWNERSHIP RECORDS PAGE 27 Dealer’s Name: Dealer’s Address: City: State: Zip Code: Serial Number: Date of Purchase: Date Installed: Notes: SERVICE AND MAINTENANCE LOG Service Service Servic e Date .
1110 West Taft Avenue Orange, CA 92865.
デバイスEarthStone BV400C-2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
EarthStone BV400C-2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEarthStone BV400C-2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。EarthStone BV400C-2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。EarthStone BV400C-2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
EarthStone BV400C-2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEarthStone BV400C-2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、EarthStone BV400C-2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEarthStone BV400C-2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。