EchoメーカーCS-400の使用説明書/サービス説明書
ページ先へ移動 of 36
X7503251602 X750012512 1 1/09 W ARNING Read rules for safe operation and instructions carefully . ECHO provides an Instruc- tion Manual and a Safety Manual.
2 CS-400 RULES FOR SAFE OPERA TION A. Kickback Safety Precautions for Chain Saw Users 1. With a basic understanding of kickback, you can reduce or eliminate the element of surprise.
3 CS-400 12. Use extreme caution when cutting small size brush and saplings because slender material may catch the saw chain and be whipped toward you or pull you off balance. 13. When cutting a limb that is under tension, be alert for spring-back so that you will not be struck when the tension in the wood bers is released.
4 CS-400 CONTENTS W ARNING The safety alert symbol accompanied by the word “W ARNING” calls attention to an act or condition which CAN lead to serious personal injury or death if not avoided. CIRCLE AND SLASH SYMBOL This symbol means the specic action shown is prohibited.
5 CS-400 TO A VOID KICKBACK 1. Hold the chain saw rmly with both hands. 2. Don’t let the nose of the guide bar contact any obstruction. 3. T ip contact may suddenly move the guide bar upward and backward, which may cause serious injury .
6 CS-400 E M I S S I O N D A T A P ACKING LIST The ECHO product you purchased has been fac - tory pre-assembled for your convenience. Due to packaging restrictions, guide bar and saw chain installation and other assembly may be necessary . After opening the carton, check for damage.
7 CS-400 6 CS-400 NOMENCLA TURE OF P AR TS * If a decal cannot be read, a new one can be ordered from your ECHO dealer. 24 16 17 18 20 19 2 1 X524-001810 890191-30131 X503-007391 21 22 23 TO A VOID KICKBACK 1. Hold the chain sa w firmly with both hands.
8 CS-400 NOMENCLA TURE OF P ARTS 1. Instruction manual - Included with unit. Read be - fore operation and keep for future reference to learn proper , safe operating techniques. 2. Safety manual - Describe operating and safety instructions for this chain saw .
9 CS-400 VIBRA TION AND COLD • It is believed that a condition called Raynaud’s Phe - nomenon, which affects the ngers of certain individu - als, may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning followed by loss of color and numbness in the ngers.
10 CS-400 SP ARK ARRESTOR MUFFLER • The spark arrestor mufer controls the exhaust noise and prevents hot, glowing particles of car - bon from leaving the mufer . Make sure the spark arrestor screen is in good repair and properly seated in the mufer .
11 CS-400 PREP ARA TION FOR USE Bolt (A) Dimple (D) Recess (E) Front hole (C) Rear hole (B) Nut (F) Guide bar Kick Guard ® Brake connector Clutch cover Brake lever (Front hand guard) T wo nuts W ARNING Saw chain is sharp! Always wear gloves when handling assembly , otherwise serious personal injury may result.
12 CS-400 4. Mount guide bar on studs and slide toward clutch to make saw chain installation easier . Install chain with cutters on top of guide bar facing forward.
13 CS-400 Handling Fuel W ARNING Fuel is VERY ammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container . • DO NOT smoke near fuel. • DO NOT allow ames or sparks near fuel.
14 CS-400 Mixing Instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container , and remix.
15 CS-400 WHEN THE ENGINE IS COLD CAUTION Make sure the bar and chain are free from any obstruction when starting the chain saw . • Move chain brake lever fully forward to lock chain brake before starting. • Fill the fuel tank with fuel mixture. It is not permitted to ll fuel above the shoulder level of fuel tank.
16 CS-400 Open choke Choke control knob WHEN THE ENGINE IS W ARM • Move chain brake lever fully forward to lock chain brake before starting. • Conrm there is fuel and chain oil in the tanks. • Move ignition switch to “RUN” position. • Securely hold the chain saw as shown and pull starter handle.
17 CS-400 RUNNING W ARNING The saw chain should not move at idle, otherwise serious personal injury may result. NOTE If saw chain moves adjust carburetor according to “Car - buretor Adjustment” instructions in this manual, or see your dealer . • When engine starts, keep idling for a few minutes.
18 CS-400 CUTTING INSTRUCTION Kickback GENERAL CAUTION • ReadtheECHO“CHAINSA WSAFETYMANUAL” included with your chain saw for additional cutting and safety instructions. • Wearsuitablehearingprotectionsuchas earmuffs or earplugs to protect against objectionable or uncomfortable loud noises.
19 CS-400 FELLING THE TREE W ARNING A falling tree can seriously damage anything it may hit - a car , a house, a fence, a power line, or another tree. There are ways to make a tree fall where you want it, so rst decide where that is! Before cutting, clear the area around the tree.
20 CS-400 Uphill position Finish cut First cut LIMBING Limbing a fallen tree is much the same as bucking. Never stand on the tree that you are limbing. When limbing, caution is the word. Be careful of the tip touching other limbs. Always use both hands.
21 CS-400 Chain brake function When the lever is pushed forward, chain brake instantly stops the chain. Chain brake unlock When the lever is fully pulled, toward the operator , brake is unlocked. Kickback Kickback motion CHAIN BRAKE OPERA TION • Set the lever in the unlocked position before starting to cut.
22 CS-400 End of the guide bar may be placed at the height of about 35 cm (14 in.). 35 cm (14 in.) AUT OMA TIC CHAIN BRAKE Kickback produced from the tip of the guide bar will trip the automatic chain brake. T o make sure that the automatic chain brake operates properly , follow these steps: 1.
23 CS-400 W ARNING Use of replacement saw chain and/or guide bar other than that specied, or operation without the “tip guard” in place, may cause severe kickback resulting in serious injury . Only use saw chain designated as, “LOW-KICKBACK,” that meets the ANSI B175.
24 CS-400 M A I N T E N A N C E A N D C A R E W ARNING Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a com - plete stop before removing obstructions, clearing debris, or servicing unit.
25 CS-400 CARBURETOR ADJUSTMENT Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjust - ments can be made. During the break-in period your engine performance will increase and exhaust emis - sions will stabilize.
26 CS-400 25 CS-400 Oil filter Fuel filter Oil tank cap Fuel tank cap 0.65 mm (0.026 in.) AIR FIL TER • Check before e very use. • Loosen cleaner cov er knob and remo v e air cleaner cover and filter . • Brush off dust lightly , or clean with compressed air , or replace the air filter .
27 CS-400 GUIDE BAR • Clean before using. • Clean the groove of the guide bar with a small screw - driver . • Clean oil holes with a wire. • Reverse guide bar periodically . • Check sprocket and the clutch and clean the bar mount area before installation of the bar .
28 CS-400 EXHAUST PORT CLEANING Level 2 T ools required: Wood or plastic scraper , Cross Head Screwdriver , 8mm Wrench Parts Required: As needed: Mufer gasket 1. Remove air lter cover and remove spark plug lead. 2. Remove engine cover (3 screws).
29 CS-400 S E T T I N G T h E S A w C h A I N Sharpen lower edge Drive link T ie strap Right hand cutter Preset tie strap Left hand cutter Guard link T op plate Side plate Depth guage Important points for proper maintenance of saw chain: • Keep the cutters sharp at all times.
30 CS-400 NOTE These angles are referred to as 91VG. T o sharpen other chains, follow chain manufac - turer ’s instructions. • Place the depth gauge tool rmly on guide bar so that depth gauge protrudes. Then le top of depth gauge with the at le until at with top of the depth gauge tool.
31 CS-400 TROUBLEShOOTING W ARNING Fuelvaporsareextremelyammableandmaycausereand/orexplosion.Nevertestforignitionspark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result.
32 CS-400 CS-400 Dimension L × W × H mm 393 × 245 × 277 (15.5 in. × 9.6 in. × 10.9 in.) Mass Power head, dry kg 4.6 (10.1 lb.) Without chain and guide bar Engine T ype Air-cooled two-stroke single cylinder Displacement mL (cm ) 40.2 (2.454 cu. in.
33 CS-400 ECHO LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated ’s Limited Warranty , provides to the original purchaser tha t this ECHO product is free from defe cts in materi al and wor kmanship .
34 CS-400 PURCHASED REP AIR P ARTS, SHORT BLOCKS AND ACCESSORIES .
35 CS-400 ECHO INCORPORA TED EMISSION CONTROL W ARRANTY ST A TEMENT FOR ECHO AND SHINDAIW A BRANDS The Environmental Protection Agency (EP A) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small of f-road engine (SORE).
CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T . ECHO, INCORPORA TED 400 O a k w O O d R O a d L a k e Z u R i c h , iL 60047-1564 www .
デバイスEcho CS-400の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Echo CS-400をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEcho CS-400の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Echo CS-400の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Echo CS-400で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Echo CS-400を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEcho CS-400の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Echo CS-400に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEcho CS-400デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
