ECSメーカーA780LM-M (V7.0)の使用説明書/サービス説明書
ページ先へ移動 of 70
Preface Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author .
ii Preface Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interfer- ence that may cause undesired operation.
iii T T T T T ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS Preface i Chapter 1 1 Introducing the Motherboard 1 Introduction........................................................................................
iv Integrated Peripherals..................................................................31 Power Management Setup.............................................................32 PCI/PnP Configurations.................................................
1 Introducing the Motherboard Chapter 1 Introducing the Motherboard Introduction Thank you for choosing the A780LM-M motherboard. This motherboard is a high performance, enhanced function motherboard that supports socket AM3 for AMD Phenom TM II processor/Athlon II/Sempron processors for high-end business or per- sonal desktop markets.
2 Introducing the Motherboard Feature Processor HyperT ransport TM T echnology is a point-to-point link between two devices, it enables integrated circuits to exchange information at much higher speeds than currently available interconnect technologies.
3 Introducing the Motherboard Onboard LAN (Optional) The onboard LAN provides the following features: This motherboard supports Ultra DMA bus mastering with transfer rates of 133/100/66/33 MB/s.
4 Introducing the Motherboard • AMD 760G & AMD SB700 • Socket AM3 for AMD Phenom TM II processor/Athlon II/Sempron processors • Supports “Hyper-Threading” technology CPU • Dual-channel.
5 Introducing the Motherboard Motherboard Components.
6 Introducing the Motherboard T able of Motherboard Components L ABEL C OMPONE NTS Socket AM3 for AM D Phenom TM II/ A th l o n I I / S empr on pr ocessor s 2. CPU_F AN CPU cooling f an conn ector 3. DDR3_1 ~2 240-pin DDR 3 SDR AM slots 4. ATX_ POWE R St anda rd 24-pin ATX power connector 5.
7 Installing the Motherboard Chapter 2 Installing the Motherboard Safety Precautions • Follow these safety precautions when installing the motherboard • Wear a grounding strap attached to a ground.
8 Installing the Motherboard Do not over-tighten the screws as this can stress the motherboard. Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard. Setting Jumpers Use the motherboard jumpers to set system configuration options.
9 Installing the Motherboard Checking Jumper Settings The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled. Jumper Settings 1. T o avoid the system unstability after clearing CMOS, we recommend users to enter the main BIOS setting page to “Load Optimal Defaults” and then “Save Changes and Exit”.
10 Installing the Motherboard Installing Hardware Installing the Processor Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface- mount resistors with the clip of the cooling fan.
11 Installing the Motherboard 1 Install your CPU. Pull up the lever away from the socket and lift up to 90-degree angle. 2 Locate the CPU cut edge (the corner with the pin hold noticeably missing). Align and insert the CPU correctly . 3 Press the lever down and apply thermal grease on top of the CPU.
12 Installing the Motherboard Installing Memory Modules This motherboard accommodates two memory modules. It can support two 240-pin DDR3 1333/1066. The total memory capacity is 8 GB.
13 Installing the Motherboard The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities.
14 Installing the Motherboard Follow these instructions to install an add-on card: 1 Remove a blanking plate from the system case corresponding to the slot you are going to use. 2 Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot.
15 Installing the Motherboard Connecting Optional Devices Refer to the following for information on connecting the motherboard’s optional devices: F_USB1~2: Front Panel USB headers The motherboard has four USB ports installed on the rear edge I/O port array .
16 Installing the Motherboard LPT : Onboard parallel port header This is a header that can ba used to connect to the printer, scanner or other devices.
17 Installing the Motherboard SPDIFO: SPDIF out header This is an optional header that provides an S/PDIF (Sony/Philips Digital Interface) output to digital multimedia device through optical fiber or coaxial connector .
18 Installing the Motherboard Installing a Hard Disk Drive/CD-ROM/SA T A Hard Drive This section describes how to install IDE devices such as a hard disk drive and a CD- ROM drive. About IDE Devices Y our motherboard has one IDE interface . IDE1: IDE Connector This motherboard supports four high data transfer SA T A ports with each runs up to 3.
19 Installing the Motherboard Refer to the illustration below for proper installation: This motherboard does not support the “Hot-Plug” function. 1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SA T A hard drive.
20 Installing the Motherboard Connecting I/O Devices The backplane of the motherboard has the following I/O ports: PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device. PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard. VGA Port Connect your monitor to the VGA port.
21 Installing the Motherboard Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: 1 Connect the CPU cooling fan cable to CPU_F AN . 2 Connect the standard power supply connector to A TX_POWER .
22 Installing the Motherboard CPU_F AN: Cooling FAN Power Connector Users please note that the fan connector supports the CPU cooling fan of 1.1A~2.2A (26.
23 Installing the Motherboard Front Panel Header The front panel header (F_P ANEL) provides a standard set of switch and LED headers commonly found on A TX or Micro A TX cases. Refer to the table below for information: Reset Switch Supporting the reset function requires connecting pin 5 and 7 to a momentary- contact switch that is normally open.
24 Installing the Motherboard Memo.
25 Using BIOS Chapter 3 Using BIOS Ab up Utility The computer uses the latest “American Megatrends Inc. ” BIOS with support for W indows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.
26 Using BIOS Press the delete key to access the BIOS Setup Utility . CMOS Setup Utility -- Copyright (C) 1985-2005, American Megatrends, Inc. f f f f v02.
27 Using BIOS Enter Select BIOS Navigation Keys The BIOS navigation keys are listed below: K E Y FUNCTION Scrolls through the items on a menu +/ - Modifies the selected field’s values F10 Saves the .
28 Using BIOS Advanced Setup This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer . Standard CMOS Setup This option displays basic information about your system.
29 Using BIOS Boot Up Numlock Status (On) This item defines if the keyboard Num Lock key is active when your system is started. Quick Power on Self T est (Enabled) Enable this item to shorten the power on testing (POST) and have your system start up faster .
30 Using BIOS Press <Esc> to return to the main menu setting page. Boot Other Device (Y es) When enabled, the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the First, Second and Third boot devices.
31 Using BIOS Integrated Peripherals This page sets up some parameters for peripheral devices connected to the system. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
32 Using BIOS Press <Esc> to return to the main menu setting page. Legacy USB Support (Enabled) Use this item to enable or disable support for legacy USB devices. Setting to Auto allows the system to detect the presence of USB device at startup.
33 Using BIOS Press <Esc> to return to the main menu setting page. PWRON After PWR-Fail (Power Off) This item enables your computer to automatically restart or return to its operating status. Resume By RING (Disabled) The system can be turned off with a software command.
34 Using BIOS Init Display First (PCI) Use this item to select which graphics controller to use as the primary boot devices. Allocate IRQ to PCI VGA (Y es) If this item is enabled, an IRQ will be assigned to the PCI VGA graphics system. Y o u set this value to No to free up an IRQ.
35 Using BIOS CPU SMAR T F AN Control (Enabled) This item allows you to enable or disable the control of the CPU fan speed by changing the fan voltage. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Smart Fan Function Help Item SMART FAN Control Enabled SMART Fan Mode Normal High Limit T emperature.
36 Using BIOS Press <Esc> to return to the main menu setting page. Frequency/V oltage Control This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have in- stalled in your system.
37 Using BIOS Supervisor Password (Not Installed) This item indicates whether a supervisor password has been set. If the password has been installed, Installed displays. If not, Not Installed displays. Change Supervisor Password (Press Enter) Y ou can select this option and press <Enter> to access the sub menu.
38 Using BIOS Save & Exit Setup Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the Setup Utility . When the Save and Exit dialog box appears, select [OK] to save and exit, or select [Cancel] to return to the main menu.
39 Using BIOS Updating the BIOS Y ou can download and install updated BIOS for this motherboard from the manufacturer’s W eb site. New BIOS provides support for new peripherals, improve- ments in performance, or fixes for known bugs.
40 Using BIOS Memo.
41 Using the Motherboard Software Chapter 4 Using the Motherboard Software Auto-installing under Windows V ista/7 The support software DVD-ROM/CD-ROM disk loads automatically under Windows V ista/7. When you insert the DVD-ROM/CD-ROM disk in the DVD-ROM/CD-ROM drive, the autorun feature will automatically bring up the install screen.
42 Using the Motherboard Software Drivers T ab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install. Browse CD The Browse CD button is the standard Windows command that al- lows you to open Windows Explorer and show the contents of the support disk.
43 Using the Motherboard Software 2. Click Next. The following screen appears: 3. Check the box next to the items you want to install. The default options are recom- mended. 4. Click Next run the Installation Wizard. An item installation screen appears: 5.
44 Using the Motherboard Software Manual Installation Insert the disk in the DVD-ROM/CD-ROM drive and locate the P A TH.DOC file in the root directory .
45 AMD RAID Configuration Setting Up a bootable RAID Array This section explains how to configure a bootable AMD RAID array . Setting Up the BIOS Use the arrow keys to select Integrated Peripherals (see Figure 1.1), then press Enter . The Integrated Peripherals screen (or a screen similar to it) appears.
46 AMD RAID Configuration 5 Enter the RAID BIOS Setup by pressing Ctrl-F when prompted, and proceed to set up the AMD RAID BIOS as described in the next section.
47 AMD RAID Configuration Select [2], then select LD 1 in the following page. 3 The Define LD Menu screen appears (Figure 1.4). Figure 1.4 Define LD Menu Using the Define a New Array Screen If necessary , press the tab key to move from field to field until the appropriate field is highlighted.
48 AMD RAID Configuration Figure 1.5 illustrates the Define a New Array screen after two disks have been assigned as RAID 0 array disks. Figure 1.5 FastBuild Utility—Array Disks Assigned Assigning the Disks 1. Select the Assignment to Y to designate a free disk to be used as a RAID array disk.
49 AMD RAID Configuration Figure 1.7 Main Menu Press ESC to exit. 4 Press Y to reboot. 3. The Main Menu screen appears (Figure 1.7). Figure 1.8 The following screen appears (Figure 1.
50 AMD RAID Configuration 1 Copy all files in " ...RAIDA TISB700FloppyWin3264" to a floppy disk. After you complete the RAID BIOS setup, boot from the Windows CD. Figure 1.10 Windows Setup—Specify Devices Installing the RAID Drivers Y our system may come with a W indows install CD that already includes AMD RAID drivers.
51 AMD RAID Configuration b Select “A TI AHCI Compatible RAID Controller -x86 platform” and press Enter for 32-bit OS or Select “A TI AHCI Compatible RAID Controller-x64 platform” and press Enter for 64-bit OS. The following Windows Setup screen appears listing both drivers:.
52 AMD RAID Configuration Memo.
Setting Up eJIFFY 53 Introduction eJIFFY is a fast boot program under Linux. Instead of waiting Windows O.S to start execution, eJIFFY is ready to provide users the instant enjoyment on web browsing, photo review and online chat just within several seconds after boot up.
Setting Up eJIFFY 54 Installation and BIOS Setup DVD Activation Finish the DVD utility setup, and then set the BIOS to complete eJIFFY activation. 1. Insert ECS software utility DVD and enter below “Utilities” screen. Click eJIFFY feature item to install.
Setting Up eJIFFY 55 3. After setting up eJIFFY under W indows, you can switch eJIFFY display/keyboard language from English to your local language. The changes will be applied after rebooting. Note: The keyboard language selection list offers several more regional keyboard setups to switch with the default English typing.
Setting Up eJIFFY 56 4. Restart your computer after eJIFFY installation. Press <DEL> or click the BIOS Setup button on the post screen to enter the BIOS setup page after boot up. 5. And then enter the Advanced Setup page to enable the item ECS eJIFFY Func- tion .
Setting Up eJIFFY 57 Entering eJIFFY The post screen appears within several seconds after boot up and it has three buttons on it, Operating system, eJIFFY and BIOS Setup. If you click eJIFFY , the following screen will appear . And If you make no choice it will enter the normal OS automatically after ten seconds.
Setting Up eJIFFY 58 Feature Icons The following illustration shows the main feature icons that eJIFFY provides on the menu. ePix: Photo viewing. eW eb: Firefo x for web br owsing/webmail and watching flash video . Shows eP al on-line connection status.
Setting Up eJIFFY 59 to open the language control panel. Keyboard Language Setup Usage F AQ Language Contr ol P anel: Besides setting English as the default interface , eJIFFY offers multi-language displays and keyboard settings for language- switch. Open the language control panel to select a preferable language setting.
Setting Up eJIFFY 60 Click the language bar here. Move your mouse pointer on the text box and press Ctrl+Space. The language bar will then appear as fol- lows.
Setting Up eJIFFY 61 How to change display language? Open the Language Control Panel and click to show the display language list. Check your desired display language. Y our selected display language will be applied after rebooting. Note: Details about eJIFFY please refer to eJIFFY in disk.
Setting Up eJIFFY 62 Memo.
63 Trouble Shooting Chapter 7 Trouble Shooting Start up problems during assembly After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty , this chapter may help to address some of the common questions using some basic troubleshooting tips.
64 Trouble Shooting c) The PC suddenly shuts down while booting up. 1. The CPU may experience overheating so it will shutdown to protect itself. Ensure the CPU fan is working properly . 2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed.
Power Bu on is pre ssed but PC fails to s tart. Y es Check if Power Supply Unit (PSU) is working No No Any Beep sound ？ No CLR CMOS and check if CPU 12V power is connecte d art the PC st Re Problem .
66 Trouble Shooting Memo.
デバイスECS A780LM-M (V7.0)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
ECS A780LM-M (V7.0)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはECS A780LM-M (V7.0)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ECS A780LM-M (V7.0)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ECS A780LM-M (V7.0)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ECS A780LM-M (V7.0)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はECS A780LM-M (V7.0)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ECS A780LM-M (V7.0)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちECS A780LM-M (V7.0)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
