Edimax TechnologyメーカーEW-7205APSの使用説明書/サービス説明書
ページ先へ移動 of 31
Wireless LAN Access Point with 5-Port Switch EW-7205APS User’s Manual.
Table of Contents Chapter 1 Introduction ............................................................................. 1 1.1 Package C ontents .......................................................................................... 1 1.2 Features ..
Introduction 1 Chapter 1 Introduction This product is a Wireless LAN Access Poin t with 5-port 10/100Mbps Fast Ethernet Switch, which allows you to build your wireless network without buying an additional hub or switch.
Introduction 2 1.2 Features Complies with the IEEE 802.11b (DSSS) 2.4GHz specification. High data rate 11, 5.5, 2 and 1Mbps network speed. Seamlessly integrate wireless and wired Ethernet LAN networks. Provides an internal 5-port switc h for wired Ethernet connection.
Introduction 3 Temp erature: Operating: 32~131°F (0~55°C) Storage: -4~158°F(-20~70°C) Humidity: 0-90% (Noncondensing) Certification: FCC, CE 1.4 Physical Description Front Panel On the Access Point’s front panel there ar e LED lights that inform you of the Access Point’s current status.
Introduction 4 Antenna Connector This round connection is standard Rev erse SMA connector where any antennas with Reverse SMA connector can connect to the Access Point. DC Adapter Port Insert the power jack of the power adapter into this port.
Wireless LAN Access Point Connection 5 Chapter 2 Wireless LAN Access Point Connection 1. Locate an optimum location fo r the Wirel ess LAN Access Point. The best location for your Access Point is usually at the center of your wireless network, with line of sight to all of your mobile stations.
Wireless LAN Access Point Configuration 6 Chapter 3 Wireless LAN Access Point Configuration 3.1 Getting Started This Access Point provides web-based conf iguration tool allowing you to configure from wired or wireless stations. Follow the instructions below to get started configuration.
Wireless LAN Access Point Configuration 7 • IP Address : Select Specify an IP Address. Specify the IP Address and Subnet Mask as following example. IP Address: 192.168.2.3 (a ny IP address within 192.168.2.2~192.168.2.254 is available, do not setup 192.
Wireless LAN Access Point Configuration 8 • IP Address: Select Specify an IP address. Specify the IP Address and Subnet Mask as following example. IP Address: 192.168.2.3 (a ny IP address within 192.168.2.2~192.168.2.254 is available, do not setup 192.
Wireless LAN Access Point Configuration 9 From Wireless Station 1. Make sure your wireless station is in the same subnet with the Access Point. Please refer to the step 1 above for configuring the IP Address and Sub Mask of the wireless station. 2. Connect to the Access Point.
Wireless LAN Access Point Configuration 10 3.2.2 Channel and ESSID You can set parameters that are used for the wireless stations to connect to this Access Point.
Wireless LAN Access Point Configuration 11 Parameter Description Basic Rate The lowest data transmission speed supports by the Access Point. If All is selected, the Access Point will aut omatically select the optimum rate allowed in the environment. The default value is “ 1~2Mbps ”.
Wireless LAN Access Point Configuration 12 Parameter Description WEP Mode You can select the 64-bit or 128-bit to encrypt transm itted data. Larger WEP key length will provide higher level of secu rity, but the throughput will be lower. You also can select Disable to transmit data without encryption.
Wireless LAN Access Point Configuration 13.
Wireless LAN Access Point Configuration 14 Parameter Description Passphrase Enter a maximum of 32 alphanumeric characters in t he text box and press Gener ate button, the Access Point will generate a WEP key automatically (refer to the 128-bit sc reen, the key is displayed after the Access Point generate the key for the wording “test”).
Wireless LAN Access Point Configuration 15 Parameter Description Filtering Enable or disable the MAC Address Filtering function. Setting You can select to permit or prohibi t the MAC addre ssed listed in the MAC Address Filtering Table to access you r wireless LAN.
Wireless LAN Access Point Configuration 16 to connect to the Access Point should be authenticated by an Authentication Server. The Authentication Server identifies the wi reless station by a set of user name and password, only wireless stations provide co rrect user name and password can connect to the Access Point and access to the network.
Wireless LAN Access Point Configuration 17 Parameter Description Enable IEEE 802.1X Enable or disable the IEEE 802.1X function. Session Idle Timeout If the wireless station doesn’t transmit or recei.
Wireless LAN Access Point Configuration 18 Parameter Description Server Type There are two kinds of servers sup ported by the Access Point including Remote RADIUS Server and TINY Server. You have to build a Remote RADIUS Server if RADIUS Serv er is selected.
Wireless LAN Access Point Configuration 19 Parameter Description New/Edit From TINY Server Users Profile table, you can enter Username, Password, Re-Type Password and press Ne w button to create a new user. The format of user name is up to 23-digit alphanumeric string; password is up to 7-digit alphanumeric string, both are case-sensitive.
Wireless LAN Access Point Configuration 20 Parameter Description Server IP Enter the RADIUS Server’s IP Address. Server Port Designate the Server Port used by the RADIUS Server an d Access Point to exchange the authentication packe t s mutually. The default port is 1812.
Wireless LAN Access Point Configuration 21 Parameter Description Current Password Enter the current password (up to 39-digit alphanu meric string) of the Access Point. The default password fo r the Access Point is blank. Note that the password is case-sensitive.
Wireless LAN Access Point Configuration 22 Parameter Description IP Address Designate the Access Point’s IP Addre ss. This IP Address should be unique in your network. The default IP Address is 192.168.2.1 . Subnet Mask Specify a Subnet Mask for your LAN segment.
Wireless LAN Access Point Configuration 23 Parameter Description Default Gateway IP Specify the gateway IP in your network. This IP address should be different from the Management IP. Domain Name Server IP This is the ISP’s DNS server IP address that they gave you; or you can specify your own preferred DNS server IP address.
Wireless LAN Access Point Configuration 24 Parameter Description DHCP Client Log This page shows all DHCP clients (LAN PCs) currently connected to your network. Number of DHCP Clients displays the number of LAN clients that are currently linked to the Access Point’s DHCP Server.
Wireless LAN Access Point Configuration 25 Parameter Description Configuration Tools Use the " Backup " tool to save the Access Point’s current configuration to a file named "backup_config.exe" on you r PC. You can then use the " Restore " tool to restore the saved configuration to the Access Poi nt.
Wireless LAN Access Point Configuration 26 Parameter Description Firmware Upgrade This tool allows you to upgrade the Acce ss Point’s system firmware. To upgrade the firmware of your Access Point, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page.
Wireless LAN Access Point Configuration 27 Parameter Description Reset In the event that the system stops responding correctly or in some way stops functioning, you can perform a reset. Your settings will not be changed . To perform the reset, click on the Apply button.
Troubleshooting 28 Chapter 4 Troubleshooting This chapter provides solutions to proble ms usually encountered during the installation and operation of the Access Point.
Troubleshooting 29 7. What is WEP? WEP stands for Wired Equivalent Privacy , a data privacy mechanis m based on a 64(40)-bit shared key algorithm. 8. What is a MAC Address? The Media Access Control (M.
デバイスEdimax Technology EW-7205APSの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Edimax Technology EW-7205APSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEdimax Technology EW-7205APSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Edimax Technology EW-7205APSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Edimax Technology EW-7205APSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Edimax Technology EW-7205APSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEdimax Technology EW-7205APSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Edimax Technology EW-7205APSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEdimax Technology EW-7205APSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。