Alamoメーカー7191852Cの使用説明書/サービス説明書
ページ先へ移動 of 110
©2009 Alamo Group Inc. $0.00 Published 03/09 P ar t No. 7191852C OPERA T OR’S MANUAL ALAMO INDUSTRIAL ® 1502 E. W alnut Seguin, T exas 78155 830-372-3551 Email: part s@alamo-industrial.
T o the Owner/Operator/Dealer All implements with moving p arts are potentially hazardou s. There is no substitute for a cautious, safe-minded operator who re cognizes the potential hazards and follows reasonable safety practice s.
In order to reduce accidents and enha nce the safe operation of mowers, Alamo Industrial, in cooperation with other industry manufacturers has developed the AEM/FEMA I ndustrial and Agri cultural Mower Safety Practices video and guide book.
Alamo Industrial Division is willing to provide one (1) AEM Mower Safety Practices V ideo Please Send Me: VHS Format – AEM/FEMA Mower Operator Safety V ideo DVD Format – AEM/FEMA Mower Operator Sa.
T ABLE OF CONTENTS SAFETY SECTION ........ ................................................. .......................................... ........... 1- 1 General Safety Instructions and Practic es ................ ....................... ..............
Operator Thrown Object Protection .......... ...................... .................... ...................... ................... ....... ............... 4-5 Tractor Lighting and SMV Emblem ..................... ................... .................
HYDRAULIC PUMPS ........................ ....................... ....................... ................... ...................... ....... .................. 5-4 FLAILHEAD .... ...................... .................... ...................... ......
.
Safety Section 1-1 © 2009 Alamo Group Inc. SAFETY SECTION.
SAFETY PA91 03/09 Safety Section 1-2 © 2009 Alamo Group In c. SAFETY General Safety Instruct ions and Practices A careful operator is the best opera tor .
SAFETY PA91 03/09 Safety Section 1-3 © 2009 Alamo Group In c. SAFETY Operator Safety Instr uctions and Practices Engine Exhaust, some of its constitue nts, a nd certa in vehicle component s contain or emit chemicals known to the st ate of California to cause cancer and birth defects or other reproductive harm.
SAFETY PA91 03/09 Safety Section 1-4 © 2009 Alamo Group In c. SAFETY PROLONGED EXPOSURE TO LOUD NOISE MA Y CAUSE PERMANENT HEARING LOSS! T ractors with or without an Implement attached can often be noisy enoug h to cause permanent hearing loss.
SAFETY PA91 03/09 Safety Section 1-5 © 2009 Alamo Group In c. SAFETY Equipment Operation Safety Instructions and Practices U se ex t reme cau ti on w h en ge tti ng on t o th e I mp l emen t t o per f orm rep a i rs, ma i n t enance an d when removing accu mulated material.
SAFETY PA91 03/09 Safety Section 1-6 © 2009 Alamo Group In c. SAFETY U se ex t reme care w h en l ower i ng or un f o ldi ng th e i mp l emen t’ s w i ngs. M a k e sure no bysta nders are close by or underneath th e wings. Allow amp le clearance around the implement when folding or unfolding the wings .
SAFETY PA91 03/09 Safety Section 1-7 © 2009 Alamo Group In c. SAFETY Never allow children to operate, ri de on, or come close to the T ractor or Implement.
SAFETY PA91 03/09 Safety Section 1-8 © 2009 Alamo Group In c. SAFETY Operate the T ractor and/or Imp lement controls on ly while pr operly seated in the T ractor seat with the seat belt secure ly fastened around y ou. Inadvertent mo vement of the T ractor or Implement may ca use serious injury or death .
SAFETY PA91 03/09 Safety Section 1-9 © 2009 Alamo Group In c. SAFETY E xtreme care s h ou ld b e ta k en w h en operat i ng near l oose o bj ects suc h as gravel, rocks, wire, and other deb ris. Inspect the area be fore mowing. Foreign ob jects should be re moved from the site to prevent machine damage and/or bodily injury or even death.
SAFETY PA91 03/09 Safety Section 1- 10 © 2009 Alamo Group In c. SAFETY Follow these guidelines to re duce the risk of equipment and grass fir es while operating, servicing, and rep airing the Mower and T ractor: -Equip the T ractor with a fire exti nguisher in an accesible location.
SAFETY PA91 03/09 Safety Section 1-11 © 2009 Alamo Group In c. SAFETY COnnecting or Disconn ecting Implement Safet y Instructions and Practices Rotary Mowers are capable un der adverse conditions of throwing objects for great distances (30 0 feet or more) and causing serio us injury or death.
SAFETY PA91 03/09 Safety Section 1- 12 © 2009 Alamo Group In c. SAFETY T ransporting Safety Inst ructions and Practices Always shut the T ractor completely down, place th e transmission in park, an d set the parking brake before you or anyone else attemp t s to connect or disco nnect the Implement and T racto r hitches.
SAFETY PA91 03/09 Safety Section 1-13 © 2009 Alamo Group In c. SAFETY Make cert ain that the “Slow Moving V ehicle” (SMV) sign is insta lled in such a wa y as to be c learly visible and legible. When transporting t he Equipment use the Tracto r flashing warning light s and follow all local traf fic regulations.
SAFETY PA91 03/09 Safety Section 1- 14 © 2009 Alamo Group In c. SAFETY Maintenance and Service Saf ety Instructions and Practices Y our dr iving vision may be reduced or impaired by the tractor , cab, or implement.
SAFETY PA91 03/09 Safety Section 1-15 © 2009 Alamo Group In c. SAFETY Periodically inspect all moving part s for wear and replace when necessary with au thorized service part s. Look for loose fastener s, worn or broken p arts, and leaky or loose fittings.
SAFETY PA91 03/09 Safety Section 1- 16 © 2009 Alamo Group In c. SAFETY Concluding Safety In structions and Practices PA R T S I N F O R M A T I O N Alamo Industrial mowers use ba lanced and matc hed system component s for blade carriers, blades, cuttershaft s, knives, knife hangers, rollers, dr ivetrain components, and be arings.
SAFETY PA91 03/09 Safety Section 1-17 © 2009 Alamo Group In c. SAFETY Decal Location NOTE: Alamo Industrial supplies safety decals on this product to promote safe operation.
SAFETY PA91 03/09 Safety Section 1- 18 © 2009 Alamo Group In c. SAFETY ITEM P ART NO. QTY LEVEL DESCRIPTION 1. 002369 1 DANGER Multiple Haza rd Flail 2. 02958241 1 DANGER Multiple Haza rd Boom 3. 02965262 1 DANGER Oil Leak/Pene tration 4. 02965100 1 INSTRUCT Use Genuin e Alamo Industrial Parts 5.
SAFETY PA91 03/09 Safety Section 1-19 © 2009 Alamo Group In c. SAFETY Decal Description Danger! Mult-Hazard W arning. Failing to follow these Safety Messages an d Operating Instructions can cause serious bo dily injury or even death to operator and others in th e area.
SAFETY PA91 03/09 Safety Section 1- 20 © 2009 Alamo Group In c. SAFETY DANGER! - Multi-Hazard Boom. T ake precautions while transporting and oper ating Boom Unit.
SAFETY PA91 03/09 Safety Section 1-21 © 2009 Alamo Group In c. SAFETY DANGER! Crushing and Pinch Point s. Moving machiney p arts can pinch or cru sh or fall- which may cause injury or death. P/N 02962765 INFORMA TION - T o prevent p remature hydraulic component failure, do not over speed the engine.
SAFETY PA91 03/09 Safety Section 1- 22 © 2009 Alamo Group In c. SAFETY W ARNING: Press urized T ank 03200437 DANGER! Keep Away Thrown Object s. Inspect the area before m owing for potential mower hazards. Remove or avoid all foreign objects such as wire, cable, met al objects, and all other foreign material.
SAFETY PA91 03/09 Safety Section 1-23 © 2009 Alamo Group In c. SAFETY W ARNING! Keep all safe ty shielding installed, repaire d and replaced when damaged so that machine stays in safe condition. P/N 00756007 DANGER! Keep Away - Rot ating Blades P/N 00756485 DANGER! Make certain that drivelin es are correct length and are se curely attached.
SAFETY PA91 03/09 Safety Section 1- 24 © 2009 Alamo Group In c. SAFETY Information that Grease Fitting is pre sent and must apply grease. P/N 000678 Instructions to properly lubricate and check mower for potential problems pr ior to operation. P/N 000108 INFORMA TION - Attention - Service Hydraulic System with Universal Tr acto r Hydraulic Oil.
SAFETY PA91 03/09 Safety Section 1-25 © 2009 Alamo Group In c. SAFETY W ARNING! A void Bodily Injury , Use 540RPM PTO S peed Only . P/N D103 Slow Moving V ehicle Decal. Keep SMV reflector clean and visible. DO NOT transport or operate without the SM V .
SAFETY PA91 03/09 Safety Section 1- 26 © 2009 Alamo Group In c. SAFETY PELIGRO! S pan ish Tr anslati on for Driveline Safety P/N 00773723 ALAMO INDUSTRIAL LOGO P/N 001651 ALAMO NAME LOGO. P/N 001650 Read Operato r ’s Manual! The operator ’ s manual is located inside this canister .
SAFETY PA91 03/09 Safety Section 1-27 © 2009 Alamo Group In c. SAFETY Federal Laws and Regulations This section is intend ed to explain in broad term s the concept and effect of federal laws an d regulations concerning emplo yer and employee equipment o perat ors.
.
Introduction Section 2-1 © 2009 Alamo Group Inc. INTRODUCTION SECTION.
INTRODUCTION PA91 03/09 Introduction Section 2-2 © 2009 Alamo Group Inc. INTRODUCTION This trimmer is designed with care and built with quality materials by skilled workers. Proper as sembly , maintenance, and operating practices, as described in this manual, will help the owner/ operator get years of satisfactory service from the machine.
INTRODUCTION PA91 03/09 Introduction Section 2-3 © 2009 Alamo Group Inc. INTRODUCTION These hydraulically driven flail trimme rs are design ed for medium-duty wo rk. They can mow pastures an d control grass and we eds on highways or industria l sites.
INTRODUCTION PA91 03/09 Introduction Section 2-4 © 2009 Alamo Group Inc. INTRODUCTION A TTENTION OWNER/ OPERA TOR BEFORE OPERA TING THIS MACHINE: 1. Carefully read the Operator’s Manual, completely underst and the Safety Messages and instructions, an d know how to operate correctly both the Mower an d Power Unit.
Assembly Section 3-1 © 2009 Alamo Group In c. ASSEMBL Y SECTION.
ASSEMBLY PA91 03/09 Assembly Section 3-2 © 2009 Alamo Group In c. ASSEMBL Y TRACTOR SELECTION Horsepower and Weight Requiremen ts The Power Arm 91 requ ires a tractor with a minimum of 30 HP in conjunction with a minimum weight of 1500Kg (1.5 tons imp.
ASSEMBLY PA91 03/09 Asse mbly Section 3-3 © 2009 Alamo Group Inc. ASSEMBL Y TRACTOR PREP ARA TION Fitting Operator Guard A tractor fitted with a cab that has a safety glass windo ws should b e used whenever possible. This is a basic safety precaution applicable to the use of all flail-type hedge trimmer s.
ASSEMBLY PA91 03/09 Assembly Section 3-4 © 2009 Alamo Group In c. ASSEMBL Y Ballast Weig ht T ractor must be st able while operating the hedge cutter s under all conditions. Pay at tention when operating on slopes. Front end ballast a s well as rear wheel weights to counterbala nce the overhang of the flail head should be added as appro priate.
ASSEMBLY PA91 03/09 Asse mbly Section 3-5 © 2009 Alamo Group Inc. ASSEMBL Y DELIVER Y 1. The machine is delivered in a partially dismantled condition. T o make re ady for att achment to the tractor it will be necessary to select a hard level surface 2.
ASSEMBLY PA91 03/09 Assembly Section 3-6 © 2009 Alamo Group In c. ASSEMBL Y *This measurement which is the fully closed fin al le ngth of the PTO drive shaf t measured button to button should be taken car efully before the PTO drive shaft is shortened to suit by cutting of f both the driving and driven members of the tube by an equal amount.
ASSEMBLY PA91 03/09 Asse mbly Section 3-7 © 2009 Alamo Group Inc. ASSEMBL Y This procedure is for initial atta chment only , for subsequent attachm ent paras marked * do not apply . If it is required to mount the machine on a different tractor , bear in mind that the engagement of the PT O shaft will alter .
ASSEMBLY PA91 03/09 Assembly Section 3-8 © 2009 Alamo Group In c. ASSEMBL Y FITTING CONTROL UNIT IN CAB The 3 lever control unit which is c abl e operated is mounted on an adju stabl e st alk that is attached to a seat bracket which is of univer sal design for mounting in many models of tractor .
ASSEMBLY PA91 03/09 Asse mbly Section 3-9 © 2009 Alamo Group Inc. ASSEMBL Y OIL REQUIREMENTS Ta n k The machine is delivered fro m the factory without o il. Fill the reservoir wit h a light hydr aulic oil as recommended in the chart until the oil level is approximat ely 2” below the top of the tank.
ASSEMBLY PA91 03/09 Assembly Section 3-10 © 2009 Alamo Group In c. ASSEMBL Y RUNNING UP PROCEDURE PA 9 1 T i 1. Ensure th at the rotor contr ol is in “STOP” positi on, start the tractor , engage PTO and allow the oil to circulate for about 5 minu tes without oper ation of the a rmhead control lever .
ASSEMBLY PA91 03/09 Assembly Sectio n 3-11 © 2009 Alamo Group Inc. ASSEMBL Y REMOV AL FROM TRACTOR 1. Select a firm level site for parking the machine.
ASSEMBLY PA91 03/09 Assembly Section 3-12 © 2009 Alamo Group In c. ASSEMBL Y PROPER TORQUE V ALUES FOR F ASTENERS The chart lists the correct tightening torqu e for fastener s.
Operation Sectio n 4-1 © 2009 Alamo Group In c. OPERA TION SECTION.
OPERATION PA91 02/08 Operation Sec tion 4-2 © 2009 Alamo Group Inc. OPERA TION ALAMO INDUSTRIAL POWER ARM 91 OPERATING INSTRUCTIONS Alamo Industrial Inte rstater flail mowers are ma nufactured with quality material by skilled workers. These mowers are designed for cutting grass and small weeds.
OPERATION PA91 02/08 Operation Sec tion 4-3 © 2009 Alamo Group In c. OPERA TION 1. St andard Equipment and Specifications St andard S pecifications Welded T ubular Frame CA T I or CA T II Three Point.
OPERATION PA91 02/08 Operation Sec tion 4-4 © 2009 Alamo Group Inc. OPERA TION 2. OPERA TOR REQUIREMENTS Safe operation of the unit is the responsibility of a qualifi ed operator .
OPERATION PA91 02/08 Operation Sec tion 4-5 © 2009 Alamo Group In c. OPERA TION 3. TRACTOR REQUIREMENTS In addition to tractor ho rsepower and size required to operate the mower unit, the tra ctor mu.
OPERATION PA91 02/08 Operation Sec tion 4-6 © 2009 Alamo Group Inc. OPERA TION Never opera te the Tr actor and Mowe r Unit with out an OPS (Operators Protective S tructure) or Cab to prevent injury from object s thrown from ground or from overhead trimmi ng.
OPERATION PA91 02/08 Operation Sec tion 4-7 © 2009 Alamo Group In c. OPERA TION 3.6 T ractor Horsepower The horsepower requir ed to operate the mower depends on many factors including vegetation to be cut, terrain condition, operator experience, an d condition of the mower and tractor .
OPERATION PA91 02/08 Operation Sec tion 4-8 © 2009 Alamo Group Inc. OPERA TION 3.7 3-Point Hitch P A91 boom mowers can att ach to tractors with either a CA T I or II hitc h. Refer to the tractor operator’s manual for the ca tegory of the tractor used.
OPERATION PA91 02/08 Operation Sec tion 4-9 © 2009 Alamo Group In c. OPERA TION 3.10 Power T ake Off (PTO) Depending on the u nit, the mower is designed to oper at e at a PTO speed of 540 or 1000 RPM. Most tracto rs operate at either 540, or a combination of 540 a nd 1000 RPM PTO speeds.
OPERATION PA91 02/08 Operation Section 4- 10 © 2009 Alamo Group Inc. OPERA TION 4.1 Boarding the T ractor Use both hands and equ ipped handrails and steps for supp ort when boarding the tractor . Never use control levers for suppor t when mounting the tractor .
OPERATION PA91 02/08 Operation Section 4- 11 © 2009 Alamo Group In c. OPERA TION 5. ST ARTING THE TRACTOR The operat or must have a com plete understanding of th e placement, func tion, and opera tional use of all tractor cont rols before starting the t ractor .
OPERATION PA91 02/08 Operation Section 4- 12 © 2009 Alamo Group Inc. OPERA TION 5.1 Connecting Att aching Head to the Boom 1. S tar t by using a hoist to lower the boom(1) down to the mower he ad (6). Align the Boom with the Head Hitch Post(7), insert the upper hitch pin(2) throug h the top hole of the Head Hitch Post (7) and up per linkage (1 1).
OPERATION PA91 02/08 Operation Section 4- 13 © 2009 Alamo Group In c. OPERA TION Always shut the T ractor completely down, place th e transmission in park, an d set the parking brake before you or anyone else attemp t s to connect or disco nnect the Implement and T racto r hitches.
OPERATION PA91 02/08 Operation Section 4- 14 © 2009 Alamo Group Inc. OPERA TION 6. PRE-OPERA TION INSPECTION AND SER VICE Before each use, a pre-ope ration inspection and service of the imple ment and tractor must be performed.
OPERATION PA91 02/08 Operation Section 4- 15 © 2009 Alamo Group In c. OPERA TION 6.2 Boom Unit Pre-Operat ion Inspection and Service Inspect and service the boom arm and head prior to operation. Damaged and/or broken part s should be repaired and/or replaced immediately .
OPERATION PA91 02/08 Operation Section 4- 16 © 2009 Alamo Group Inc. OPERA TION FRAME ASSEMBL Y • Inspect condition of mounting frame weldment. • Inspect condition of King Post frame. • Ensure all bolt s and screws are in position and are properly to rqued.
OPERATION PA91 02/08 Operation Section 4- 17 © 2009 Alamo Group In c. OPERA TION Relieve hydraulic pressure prio r to doing any maintenance or re pair work on the Implement. Place the Mower Head on the ground or secure ly supported on blocks or st ands, disengage the PTO, and turn off the engine.
OPERATION PA91 02/08 Operation Section 4- 18 © 2009 Alamo Group Inc. OPERA TION Do not operate this Equ ipment with hy draulic oil or fuel leaking. Oil and fuel are explosive and the ir presence could present a haza rd.
OPERATION PA91 02/08 Operation Section 4- 19 © 2009 Alamo Group In c. OPERA TION Boom Mower PRE-OP ERA TION Inspection Mower ID#________________ Make ____________________ Date: ________________ Shift.
OPERATION PA91 02/08 Operation Section 4- 20 © 2009 Alamo Group Inc. OPERA TION T ractor PRE-OPERA TION Inspection Mower ID# ________________ Make ____________________ Date: ________________ Shift __.
OPERATION PA91 02/08 Operation Section 4- 21 © 2009 Alamo Group In c. OPERA TION 7. OPERA TING THE BOOM MOWER 7.1 Machine Controls Moving the Arm control le vers away from the cables will result in “LIft Down”, “Angle Down” and “Reach Out”.
OPERATION PA91 02/08 Operation Section 4- 22 © 2009 Alamo Group Inc. OPERA TION 7.3 Forward Speed T ractor ground speed is d etermined by common sense and experience. It should be slow enough to allow sufficient time for the flails to cut the work without over loading.
OPERATION PA91 02/08 Operation Section 4- 23 © 2009 Alamo Group In c. OPERA TION 7.9 Hedge Cutting Procedure Upward Cutting The flail head is assembled at th e factory for the flails to cut with an upward motion. Upward cutting produc es a cleaner finis h minimizes split stems and is ideal for a light hedge that has been regularly maint ained.
OPERATION PA91 02/08 Operation Section 4- 24 © 2009 Alamo Group Inc. OPERA TION Reversing Rot ation (Si Only) Fully extend th e armhead and lower flail to the ground to minimize oil loss. Release the rotor hoses from either the flail motor o r the rotor control valve and interchang e the connections.
OPERATION PA91 02/08 Operation Section 4- 25 © 2009 Alamo Group In c. OPERA TION 7.10 Lif t Float Kit (Optional) Ground scrub flailing can be a slow tedious task requ iring a high degree of operator concentration especially when working on a rough or rising ground.
OPERATION PA91 02/08 Operation Section 4- 26 © 2009 Alamo Group Inc. OPERA TION 7.1 1 Flail T ypes T wo types of flail are available : The F91 H is a cast flail suitable fo r continuous hedge and scru b cutting. It will also cut grass, but the finish will be inferior to that produ ced by the F91 G and the power requirement s greater .
OPERATION PA91 02/08 Operation Section 4- 27 © 2009 Alamo Group In c. OPERA TION 8 . DRIVING THE TRACT OR AND IMPLEMENT Safe tractor transport r equires the operator to po ssess a thorou gh knowledge of the model being operated and precaution s to take while driving with an attached implem ent.
OPERATION PA91 02/08 Operation Section 4- 28 © 2009 Alamo Group Inc. OPERA TION T ransport only at speeds where you can maint ain control of the equipment. Seriou s accidents and injuries can result from operating this equipment at high speeds. Understand the Tra ctor and Implement and how it hand les before transporting on street s and highways.
OPERATION PA91 02/08 Operation Section 4- 29 © 2009 Alamo Group In c. OPERA TION 8.2 Brake and Differential Lock Setting Make sure the tracto r brakes are in good operating conditio n. Tractor br akes can be set to operate independ ently allowing single rear wheel braking action or locked to gether to provide simultaneo us rear wheel braking.
OPERATION PA91 02/08 Operation Section 4- 30 © 2009 Alamo Group Inc. OPERA TION 8.3 T ransport Position • For tran sport on public highway , the boom must be folded within the overall width of the tractor .Position the arm until the boom head is approximately 4 ft.
OPERATION PA91 02/08 Operation Section 4- 31 © 2009 Alamo Group In c. OPERA TION 8.4 Driving the T ractor and Boo m S tart of f driving at a slow speed and gradu ally increase your speed while maintainin g complete control of the tractor .
OPERATION PA91 02/08 Operation Section 4- 32 © 2009 Alamo Group Inc. OPERA TION 9.1 OPERA TING INSTRUCTIONS 1. Engage the PT O shaft at low en gine RPM and speed the engine u p after blades ar e fully engaged. Never engage the PT O shaft at a high engine RPM.
OPERATION PA91 02/08 Operation Section 4- 33 © 2009 Alamo Group In c. OPERA TION When cutting folia ge and fine shredding is desired, run the mower level or slightly lower in the rear so as to keep the material in the mower until it is shredded. This will require more power but will shred better .
OPERATION PA91 02/08 Operation Section 4- 34 © 2009 Alamo Group Inc. OPERA TION 9.2 Foreign Debris Hazards Before mowing, in spect the area to make sure there are no foreign obje cts that the mower blades could hit or b ecome entangled with. Remove all foreign objects and debris.
OPERATION PA91 02/08 Operation Section 4- 35 © 2009 Alamo Group In c. OPERA TION Rotary Mowers are capable un der adverse conditions of throwing objects for great distances (30 0 feet or more) and causing serio us injury or death. Follow safety messages carefu lly .
OPERATION PA91 02/08 Operation Section 4- 36 © 2009 Alamo Group Inc. OPERA TION 9.5 Operating Speed and Ground S peed Ground speed for mowing will depend upon the height, type, and density of veget ation to be cut. Do Not exceed 2 MPH while op erating.
OPERATION PA91 02/08 Operation Section 4- 37 © 2009 Alamo Group In c. OPERA TION There are obvio us and hidden potential hazards in the operation of this Mower . REMEMBER! This machine is of ten operated in heavy br ush and in heavy weeds. The Bla des of this Mower ca n throw objects if shields are not pro perly installed and maint ained.
OPERATION PA91 02/08 Operation Section 4- 38 © 2009 Alamo Group Inc. OPERA TION 9.7 Shutting Down the Attached Head T o shut down attached mower head , first bring the tractor to a complete stop. Decrease engine RPM to idle then disengage cutterhea d.
OPERATION PA91 02/08 Operation Section 4- 39 © 2009 Alamo Group In c. OPERA TION 9.8 TRACTOR, BOOM , AND A TT ACHED HEAD STORAGE Properly prep aring and storing the unit at the end of the season is critical to maintainin g its appearance a nd to help ensure years of dep endable service.
OPERATION PA91 02/08 Operation Section 4- 40 © 2009 Alamo Group Inc. OPERA TION NOTE: Ensure that the mo wer sections are fully raised and that the transp ort locks are engaged for e ach section.
OPERATION PA91 02/08 Operation Section 4- 41 © 2009 Alamo Group In c. OPERA TION O n l y t ow th e I mp l emen t b e hi n d a proper l y s i ze d an d equ i ppe d T rac t or which exceeds the weight of the Impl ement by at least 20%. DO NOT tow the Imp lement behind a tr uck or other type of vehicle.
OPERATION PA91 02/08 Operation Section 4- 42 © 2009 Alamo Group Inc. OPERA TION When operating on public roads, have consideration for other road u sers. Pull to the side of the road occasionally to allow all following traffic to pass. Do not exceed the lega l speed limit set in your country for agricultural tra ctors.
OPERATION PA91 02/08 Operation Section 4- 43 © 2009 Alamo Group In c. OPERA TION 10.2 Hauling the T racto r and Implement Before transporting a loade d tractor and implement, measure the height and width dimensions and gro ss weight of the complete loaded unit.
OPERATION PA91 02/08 Operation Section 4- 44 © 2009 Alamo Group Inc. OPERA TION 1 1. TROUBLESHOOTING GUIDE TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY Hydraulic Cylinder Hydraulic level low . Check hydraulic fluid level. Not Working (See sight gauge on tan k) Pump not functioning Attempt to use another cylinde r or properly .
OPERATION PA91 02/08 Operation Section 4- 45 © 2009 Alamo Group In c. OPERA TION TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY S tructural Membe rs Rough treatment. Use only on elements it is designe d Failure to cut such as grass, weeds, brush, trees. Excessive Vibrations Check Gear box bolts.
OPERATION PA91 02/08 Operation Section 4- 46 © 2009 Alamo Group Inc. OPERA TION TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY Gearbox Leaking Damaged oil seal Replace seal. Bent shaft. Replace oil seal and shaf t. Shaft roug h in oil seal area. Replace or repair shaft.
Maintenanc e Section 5-1 © 2009 Alamo Group Inc. MAINTENANCE SECTION.
MAINTENANCE PA91 03/0 9 Maintenance Section 5-2 © 2009 Alamo Group Inc. MAINTENANCE LUBRICA TION General Refer to the lubrication diagram an d grease daily all the points show n. 1. Power ta ke-off shaf t - The PTO shaf t should be regularl y examined to ensure that it is in good condition together with the g uards.
MAINTENANCE PA91 03/0 9 Maintenance Section 5-3 © 2009 Alamo Group Inc. MAINTENANCE HYDRAULIC SYSTEM Oil Supply Check the oil level in the reservoir da ily . The first oil change should take p l ace th e first 250 hour s of operation and every 500 hours or every 12 months thereafter .
MAINTENANCE PA91 03/0 9 Maintenance Section 5-4 © 2009 Alamo Group Inc. MAINTENANCE HYDRAULIC PUMPS 1. All pumps ar e rotate clockwise. No routine maint enance is necessar y other than a periodical ch eck for tightness of the mounting bolt s and a visual check fo r oil leakage especially around the pump supply and pressure unions.
MAINTENANCE PA91 03/0 9 Maintenance Section 5-5 © 2009 Alamo Group Inc. MAINTENANCE CABLE OPERA TED ARMHEAD CONTROL V AL V E Replacing Damaged or Worn S pool “O” Rings 1.
MAINTENANCE PA91 03/0 9 Maintenance Section 5-6 © 2009 Alamo Group Inc. MAINTENANCE Main Relief V alve The main relief valve is pressure set at the factory to 1 800 PSI (125 Bar) and is non-adjust able. A sticking relief valve will probably cause overhea ting and/or loss of power .
MAINTENANCE PA91 03/0 9 Maintenance Section 5-7 © 2009 Alamo Group Inc. MAINTENANCE HYDRAULIC RAMS Ram Seal Replacement - General Information 1 1. Whenever possible the ram should be removed from the machin e and cleaned off before dismantling on a clean work bench.
MAINTENANCE PA91 03/0 9 Maintenance Section 5-8 © 2009 Alamo Group Inc. MAINTENANCE ROT OR CONTROL V AL VE/RELIEF V AL V E Relief V alve The relief valve within the block is pre- calibrated to gi ve setting of 3000 PSI (210 Bar). No servicing should be required other than cleaning and examining for damage should a malfunction occur .
MAINTENANCE PA91 03/0 9 Maintenance Section 5-9 © 2009 Alamo Group Inc. MAINTENANCE Replacing Shaf t Seals 1. The doub le shaft seal assembly m ust be assembled wit h the 7 MM. wide sing le lip seal fitted first with the 1 MM. thick lip support washer on top.
ALAMO-INDUSTRIAL LIMITED W ARRANTY 1. LIMITED W ARRANTIES 1.01. Alamo Industrial warrants for one year from the purchase dat e to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser 1.
T o keep your implement running efficien tly and safely , read your manual thoroughly and follow these dire ctions and the Safety Messages in this Ma nual. The T able of Cont ents clear ly identifies each section where you can easily find the information you need.
P A91-SOM-02/08 P/N 7191852 C Printed U.S.A.
デバイスAlamo 7191852Cの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Alamo 7191852Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAlamo 7191852Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Alamo 7191852Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Alamo 7191852Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Alamo 7191852Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAlamo 7191852Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Alamo 7191852Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAlamo 7191852Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。